6) Study the data transfer program of the figure below and answer the following questions: a. When S1 is open, what decimal number will be stored in integer word address N7:13 of the MOV instruction? b. When S1 is on, what decimal number will be stored in integer word address N7:112 of the MOV instruction? c. When S1 is on, what decimal number will appear in the LED display? d. What is required for the decimal number 216 to appear in the LED display? Inputs Ladder logic program Output L1 L2 S1 - MOV- MOVE O-S1 Source N7:112 Destination N7:13 N7:13 LED display -N7:112 Thumbwheel switch

6) Study the data transfer program of the figure below and answer the following questions: a. When S1 is open, what decimal number will be stored in integer word address N7:13 of the MOV instruction? b. When S1 is on, what decimal number will be stored in integer word address N7:112 of the MOV instruction? c. When S1 is on, what decimal number will appear in the LED display? d. What is required for the decimal number 216 to appear in the LED display? Inputs Ladder logic program Output L1 L2 S1 - MOV- MOVE O-S1 Source N7:112 Destination N7:13 N7:13 LED display -N7:112 Thumbwheel switch

Systems Architecture

7th Edition

ISBN:9781305080195

Author:Stephen D. Burd

Publisher:Stephen D. Burd

Chapter4: Processor Technology And Architecture

Section: Chapter Questions

Problem 15VE: A(n) ________________ instruction always alters the instruction execution sequence. A(n)...

See similar textbooks

Similar questions

The time it takes to perform the fetch instruction and decode instruction steps is called the execution time. True or false?
A(n) ________________ instruction always alters the instruction execution sequence. A(n) ______________ instruction alters the instruction execution sequence only if a specified Condition is true.
Using the mov.w instruction we copy the 16-bit word 0xB612 to the address 0x1C20. You do notneed to know any details of the instruction here, all you care is that the word (i.e., 16 bits) isstored at the given address.(a) What is the byte that is stored in location 0x1C1F?(b) What is the byte that is stored in location 0x1C20?
Instruction : SUB Rd, Rs, Rt a. What are the values of control signals generated by the control in Figure I for the above instruction? b. Which resources (blocks) perform a useful function for this instruction? c. Which resources (blocks) produce outputs, but their outputs are not used for this instruction? d. Which resources produce no outputs for this instruction Branch Add Add ALU operation Data MemWrite Register PC Address Instruction Address Zero Registers ALU Register Data Instruction memory Register Regwrite memory Data MemRead Contrel Figl
12. The MOD R/M Byte: If the mod R/M byte has the following data in it: mod 11 reg 011 a. What addressing mode is being use in the instruction? b. What is the source register (use 16 bit register)? c. What is the destination register(use 16 bit register)? d. What does the assembly instruction look like? r/m 000
Assume AL=35h; CL=05. Write the content of AL after RCR AL, CL - showing the calculation steps. Assume a CLC instruction before this RCR instruction. (Note : Solve the question in paper, scan and upload along with the other Part B and C answers) A- BI E E I E
1. Study this program , then answer the questions that follow : MOV AL, 64H ADD AL,27H DAA a) What does the accumulator contain immediately after the ADD instruction is executed ? What do the CY and AC flags contain? b) What does the accumulator contain after the DAA instruction is executed? What do the CY and AC flags contain? 2. Write a subroutine that will perform the function of the DAA instruction.
For the RISC-V assembly instructions below, what is the corresponding C statement? Assume that the variables f, g, h, i, and 3 are assigned to registers x5, x6, x7, x28, and x29, respectively. Assume that the base address of the arrays A and B are in registers x10 and 11, respectively. sub x30, x28, x29 slli x30, x30, 2 add x3, x30, x10 add x4, x30, x11 Iw x30, 0(x3) 1w x31, 0(x4) add x30, x30, x31 sw x30, 16 (x11)
The instruction, Add #45,R1 does A. Adds 45 to the value of Rl and stores it in R1 Adds the value of 45 to the address of R1 and stores 45 in that address C. None of the mentioned D. Finds the memory location 45 and adds that content to that of R1 B.
Q3/ Initially assume all flags are set, find the values of status flags and AL after each instruction MOV AX,73 SBB AL,80 INC AX CMP AL, AH
I have been searching in my textbook and could not find anything to help me solve this problem. Could anyone help me please? Registers in RISC-V are 64-bit. For the sake of simplicity, consider the following instructions operating on 32-bit registers. Assume that registers x5 and x6 hold the values 0xBBBBBBBB and 0x00000000, respectively. What is the value in x6 for the followingslli x6, x5, 6 Using the result from the part above, what is the value in x6 for the following instruction.srli x6, x6, 6
Datapath for the LDI Instruction 7 Recently we have been discussing the importance of the datapath and its relationship to the Register Transfer Notation and control signals need to execute instructions in the datapath. Answer the following questions about this specific What is the ML (or binary instruction) of this single instruction? Give your answer in hexadecimal. instruction: type your answer... LDI R4, data Where the label data is at address x3005, and the LDR instruction is at address x3000. What is the Register Transfer notation for this instruction? Remember to change the destination and source registers to the actual registers of the instruction. type your answer... List in order all the controls signals required to execute this instruction. You do not need to list the signals for fetching and decoding the instruction.