6.. A cantilever beam is 2.5 m long, and carries a concentrated load of 380 N at its midpoint, and a uniformly distributed load of 400 N/m over a span from its free end to a point 0.5 m from the free end. Neglecting the mass of the beam itself, draw the shear force and bending moment diagrams for the beam. Show all calculations as well

6.. A cantilever beam is 2.5 m long, and carries a concentrated load of 380 N at its midpoint, and a uniformly distributed load of 400 N/m over a span from its free end to a point 0.5 m from the free end. Neglecting the mass of the beam itself, draw the shear force and bending moment diagrams for the beam. Show all calculations as well

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter6: Beams And Cables

Section: Chapter Questions

Problem 6.42P: For the beam AB shown in Cases 1 and 2, derive and plot expressions for the shear force and bending...

See similar textbooks

Similar questions

A simply supported beam, 50mm wide by 100mm high and 300 mm long is subjected to a concentrated load of 3000 N at a point 100 mm from one of the supports. Draw the shear force and bending moment diagrams for the beam.
A simply supported beam of 7 m span with overhangs rests on supports which are 4 m apart. The left end overhanging is 2 m. The beam carries loads of 30 kN and 20 kN on the left and the right ends respectively apart from a uniformly distributed load of 25 kN/m between the supporting points. Draw the shear force and bending moment diagrams.
For the simply supported beam subjected to the loading shown, derive equations for the shear force V and the bending moment M for any location in the beam. (Place the origin at point A.) Let w = 19.5 kips/ft, a=6.0 ft, and b=21.5 ft. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise.Calculate the reaction forces By and Cy acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since Bx = 0, it has been omitted from the free-body diagram.) Use your shear-force and bending-moment diagrams to determine the maximum positive bending moment, Mmax, pos, the maximum negative bending moment, Mmax, neg, and their respective locations, xmax, pos and xmax, neg. Use the bending-moment sign convention detailed in Section 7.2. The maximum negative bending moment is the negative moment with the largest…
For the simply supported beam subjected to the loading shown, derive equations for the shear force V and the bending moment M for any location in the beam. (Place the origin at point A.) Let w = 19.5 kips/ft, a=6.0 ft, and b=21.5 ft. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise.Calculate the reaction forces By and Cy acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since Bx = 0, it has been omitted from the free-body diagram.) Determine the shear force acting at each of the following locations:(a) x = 6.0- ft (i.e., just to the left of support B)(b) x = 6.0+ ft (i.e., just to the right of support B)(c) x = 26.5 ft(d) x = 27.5- ft (i.e., just to the left of support C)Note that x = 0 at point A. When entering your answers, use the shear-force sign convention detailed in Section…
For the simply supported beam subjected to the loading shown, derive equations for the shear force V and the bending moment M for any location in the beam. (Place the origin at point A.) Let w = 19.5 kips/ft, a=6.0 ft, and b=21.5 ft. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise.Calculate the reaction forces By and Cy acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since Bx = 0, it has been omitted from the free-body diagram.) Determine the bending moment acting at each of the following locations:(a) x = 6.0 ft (i.e., at support B)(b) x = 26.5 ftNote that x = 0 at point A. When entering your answers, use the bending-moment sign convention detailed in Section 7.2.Answers: (a) M = kips-ft (b) M = kips-ft
For the simply supported beam subjected to the loading shown, derive equations for the shear force V and the bending moment M for any location in the beam. (Place the origin at point A.) Let a=12.0 ft, b=6.5 ft, c= 7.0 ft, w = 7 kips/ft and M = 230 kip-ft. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise.Calculate the reaction forces Ay and Cy acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since Ax = 0, it has been omitted from the free-body diagram.) Determine the shear force acting at each of the following locations:(a) x = 0+ ft (i.e., just to the right of support A)(b) x = 12.0 ft (i,e., at point B)(c) x = 18.5- ft (i.e., just to the left of the support C)(d) x = 18.5+ ft (i.e., just to the right of the support (C)(e) x = 24.5 ftNote that x = 0 at support A. Determine the bending…
For the simply supported beam subjected to the loading shown, derive equations for the shear force V and the bending moment M for any location in the beam. (Place the origin at point A.) Let a=14.0 ft, b=3.0 ft, c= 7.0 ft, w = 9 kips/ft and M = 300 kip-ft. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise. " " Answers: Ay= Cy= b Calculate the reaction forces Ay and Cy acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since Ax = 0, it has been omitted from the free-body diagram.) i W i a W M a B M B ес b kips kips с Cy с X с -X
The shape of the bending moment diagram for a uniform cantilever beam a. carrying a uniformly distributed load over its length is
For the simply supported beam subjected to the loading shown, derive equations for the shear force V and the bending moment M for any location in the beam. (Place the origin at point A.) Let a=11.0 ft, b-4.5 ft, c= 7.5 ft, w = 4 kips/ft and M = 250 kip-ft. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise. 27 W Ay a b Calculate the reaction forces Ay and Cy acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since Ax = 0, it has been omitted from the free-body diagram.) W M a B M C b C C₂ C -X
Draw the Shear Force and Bending Moment Diagram for the loaded simply supported beam shown below. Ignore the self-weight of the beam
SITUATION 4: The given continuous beam supports a uniform load with magnitude w. It has an internal hinge at C. (a) Calculate the maximum uniform load w that the beam can carry if it has a moment capacity of 65 kN-m for negative bending; (b) Calculate the maximum uniform load w that the beam can carry if it has a moment capacity of 85 kN-m for positive bending; (c) Calculate the maximum uniform load w that the beam can carry if it has a shear capacity of 40 kN. A B C D 5 m 2 m 3 m
For the simply supported beam subjected to the loading shown, derive equations for the shear force V and the bending moment M for any location in the beam. (Place the origin at point A.) Let a=4.00 m, b=5.25 m, c= 2.75 m, P = 36kN and M = 195kN-m. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise. A Answers: Ay= Cy= b Calculate the reaction forces Ay and Cy acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since Ax = 0, it has been omitted from the free-body diagram.) i i a M a B M B b kN 2 C KN C Cy C P с X P