7. Bromophenol Blue, a reagent or standard that is usually used to determine the void volume of a gel filtration chromatography column, has an approximate molecular weight of 2,000,000 Da. 8. The recommended range of sample volume to be loaded onto the gel filtration chromatography column is within 5-10 percent of the column's total volume. 9. A calculated partition coefficient (Kav) that is less than 1 indicates that no solute or protein entered the pores of the gel filtration chromatography column resin/beads.

7. Bromophenol Blue, a reagent or standard that is usually used to determine the void volume of a gel filtration chromatography column, has an approximate molecular weight of 2,000,000 Da. 8. The recommended range of sample volume to be loaded onto the gel filtration chromatography column is within 5-10 percent of the column's total volume. 9. A calculated partition coefficient (Kav) that is less than 1 indicates that no solute or protein entered the pores of the gel filtration chromatography column resin/beads.

Curren'S Math For Meds: Dosages & Sol

11th Edition

ISBN:9781305143531

Author:CURREN

Publisher:CURREN

Chapter10: Reconstitution Of Powdered Drugs

Section: Chapter Questions

Problem 7.2P

See similar textbooks

Similar questions

1. Why is necessary to remove fat and tendons from the heart sample? 2. Why is necessary to completely grind the beef? 3. Why is necessary to balance the homogenate tubes for centrifugation? 4. How do you prepare a 100mL of 0.1 M phosphate buffer? 5. From the anterior buffer, how do you make 100mL of 0.05 M? 6. Calculate the amount of ammonium sulfate necessary to get a 20% solution? 7. Which is the importance of dialysis?
DILUTION COLONY COUNT CFU/mL 1:106 155000 1:107 15500 1:108 1550 1:109 155 Given these values how would I fill in the rest of this serial dilution table? Also, what would be a 1:1 CFU/mL value based on this table?
6) 1 mL of supernatant is required for a procedure. The final colored solution proves to be too high to read accurately on the spectrophotometer. 100 μL of supernatant and 900 μL of distilled water are substituted for the original supernatant and the procedure, run as before. The reading from the standard curve is 46 mg/dL. What is the actual amount of substance in the patient serum?
3) With our 12.5 ug/mL solution, we will make serial dilutions with a dilution factor of 2. We want to make 1 mL of 1/2, 1/4, 1/8, 1/16, 1/32, and 1/64 dilutions. Draw a diagram describing how you will conduct the serial dilutions and insert it below. The 1/2 dilution (tube 2) will be made from the 12.5 ug/mL solution (tube 1). The 1/4 dilution (tube 3) will be made from the 1/2 dilution (tube 2L
How much of 10,000x SYBR safe would you add to 50 ml to make a final concentration of 1x? V1= 0.005mL B.How will you set up the serial dilution? How many tubes do you need? What is the concentration in each? How much LB will you add to each tube? What volume of cells will you add?
4 mL of 10% TCA solution was added to 1 mL of serum and after mixing, it was waited for two minutes and filtered through non-phosphorus filter paper. 1 mL of the filtrate was taken and 13 mL of distilled water, 4 mL of sulfomolybdic acid and 2 mL of dilute SnCl2 solution were added and mixed, and after waiting for 15 minutes, the absorbances of the obtained solutions against pure water at 520 nm were read. If the function of the calibration graph obtained with 0.5-2.5 mg/mL standard phosphorus solutions is y= 0.245x + 0.107 and the absorbance value of the serum sample is 0.109, what is the amount of phosphorus in the sample?
6. You were asked by your laboratory instructor to prepare the following: 12 plates (use maximum volume) and 6 big slants of Malt Yeast Extract Glucose Agar. Calculate for the total volume of the media you need to prepare, and the amount (in grams) needed to be weighed for each component. Refer to the table below. Note: Show all computations. Use 3 significant figures for your final answer. Amount (per 200 ml) 0.6 g 0.6 g 4.0 g 3.4 g Malt Yeast Extract Glucose Agar Malt extract Yeast extract Glucose Peptone Agar 1.7 % Table 1. Glassware used in media preparation and their approximate volume capacity. Glassware Approximate volume* Petri dish 15-20 ml Big test tubes (18 mm diameter) as stabs/broth 10 ml as slants 6-8 ml Small tubes (13 mm diameter) as stabs/broth 5 ml as slants 3 ml It is prescribed not to exceed 60% of the total capacity of the container. Erlenmeyer flasks, media bottles, etc. *Volumes may vary depending on the laboratory practices.
A 15kg doe diagnosed with pregnancy toxaemia requires a dextrose fluidsupplementation. Given a dosage of 0.2ml/kg of body weight, prepare a 5%dextrose solution from a stock solution of 50%.
1- Are the following changes in conditions likely to increase or decrease retention time? a. faster flow rate b. longer column c. longer connector between column and detector d. higher analyte concentration e. higher temperature f. larger sample size g. using a less polar column while doing a reverse-phase separation h. using a less polar mobile phase while doing a reverse-phase separation 2- In what order will the following substances elute? • In reverse-phase liquid chromatography: a. butylamine, 2-butylene, ethylamine, ethylene b. benzene, chlorophenol, phenol, trichlorophenol • In gas chromatography with a polar column: c. butanol, methanol, water • In gas chromatography with a nonpolar column: d. butanol, methanol, water • In ion chromatography: e. bromide, fluoride, sulfide
3. 4. Draw a picture of a ten-fold serial dilution. Please use 10ul (1ml) of initial sample into 9ml of solution. Show a picture of what a serial dilution would look like up through ten- thousand-fold. You can draw this and take a picture.
You have a sample at 50 ng/ul and you would like to load 400ng of this sample on a lane of an agarose gel. You also have TE buffer as diluent and 6x loading dye. Your total sample should be 12ul. Calculate the amounts of each reagent necessary to prepare this sample for gel loading.
1mL Stock #1 1mL 2000060 9mL #2 9mL wwwww #3 4. 1mL 0000000 A 9mL wooooo #4 0.1m/L O 1mL 5000000 B 9mL #5 1mL 1mL 9mL wwwwww #6 0.1mL 1mk O. D Using the picture serial dilution scheme and the following information (plate A has 276 colonies, plate B has 298, plate C has 2, and plate D has 30), calculate the average number of colony forming units per mL in the stock tube. Make sure to only use countable plates. Round your answer to the nearest one. Write only the number with any needed commas or decimals. Do not include units.