7.49.1 For the RC circuit shown in the image below, the current waveform is applied. If v (0) = 0, R1 = 9 N and R2 = 10 2, determine the voltage across the capacitor, v V when t= 0.3 s. Please pay attention: the numbers may change since they are randomized. Your answer must include 3 places after the decimal point, and the proper SI unit. is (A) A 1 t (s) (a) R2 + is R1 0.5 F (b) Your Answer: Answer units

7.49.1 For the RC circuit shown in the image below, the current waveform is applied. If v (0) = 0, R1 = 9 N and R2 = 10 2, determine the voltage across the capacitor, v V when t= 0.3 s. Please pay attention: the numbers may change since they are randomized. Your answer must include 3 places after the decimal point, and the proper SI unit. is (A) A 1 t (s) (a) R2 + is R1 0.5 F (b) Your Answer: Answer units

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter19: Capacitors

Section: Chapter Questions

Problem 14RQ: A postage stamp mica capacitor has the following color marks starting at the upper left dot: yellow,...

See similar textbooks

Similar questions

A postage stamp mica capacitor has the following color marks starting at the upper left dot: yellow, violet, brown, green, no color, and blue. What are the capacitance value, tolerance, and voltage rating of this capacitor?
In the circuit below, Find the voltage across the inductor at time t = 0.000909 s. The values are V1 = 146V, R = 4.4 ohms, L =0.02 henries
A voltage of 6 cos(100rt) V is fed as y-input to a CRO. The waveform seen on the screen of the CRO is shown in the figure. The Y and X axes settings for the CRO are respectively
Determine the total capacitance, total charge, individual voltage drop and charges across each capacitor. Use two decimal places for your answer. Put your answer for the individual voltage and charge for each capacitor in a table for faster checking. Thank you! Here are the values for the capacitors: C1 = 55 C6 = 50 C2 = 25 C7 = 17 C3 = 49 C8 = 44 C4 = 22 C9 = 53 C5 = 45 C10 = 44
A capacitor in series with a 200 ohms resistor draws a current of 0.3 ampere from 120 volts, 60 hz source. What is the value of the capacitor in microfarad? a. 8.7 b. 9.7 c. 6.7 d. 7.7
The figure below shows a simple RC circuit with a 3.30-μF capacitor, a 4.40-M resistor, a 9.00-V emf, and a switch. What are the following exactly 9.00 s after the switch is closed? (a) the charge on the capacitor 13.7204 UC (b) the current in the resistor 0.0110522 x Your response is off by a multiple of ten. HA (c) the rate at which the capacitor is storing energy μW (d) the rate at which the battery is delivering energy μW
7- For the circuit below a) Find tbe time constant b) Sketch the waveforms for in, a when you close the switch AK 31m H
1. A purely resistive circuit the current is leading by 90° with respect to voltage. 2. A purely inductive circuit the current is lag behind the voltage by 90°. 3. A purely capacitive circuit the current is lead by 90° with respect to the voltage. 4. A capacitor element stored magnetic energy. 5. An inductor element stored electrical energy. 6. Resistor elements consume power. 7. Angle between current and voltage is called power. 8. The power factor angle for a purely resistive is zero. 9. The power factor angle for a purely inductive load is -90°. 10. The power factor of a purely capacitive is leading.
Using the series circuit in Figure 3 consisting of a voltage source V, the resistor R and the fully uncharged capacitor C, how to find the value of the capacitance C considering as known data the time constant of the circuit T and the value of the resistor R? V ww R
A series R–L–C circuit comprises a 5µF capacitor, a 4ohm resistor and a variable inductance L. The supply voltage is 10∠0◦ V at a frequency of 159.1 Hz. The inductance is adjusted until the p.d. across the 4 ohm resistanceis a maximum. Determine for this condition (a) the value of inductance, (b) the p.d. across each component and (c) the Q-factor of the circuit.
please help with this circuits problem
The givens are I1 = 0.219A, R1 = 66 ohms, R2 = 38 ohms, C = 0.1 farads. What is Vc across the capacitor at time t = 4.58 seconds?