7000 6000 5000 Z4000 3000 2000 Line of maxima F=7000 N + F=6000 N F₂ =5000 N F.=4000 N 1000 0 0 2 4 6 8 10 12 a[deg] FIGURE 1.74. Lateral force behavior of a sample tire for different normal loads as a function of slip angle

: | %85 || 2 100 Q1/ Two Forces Shown in Fig. (1) acts on the bracket, determine the effect of these two forces (using Parallelogram method). 150N F₁-200 N ||| Mech. eng. 1st atte - - ٩:٣٤ 71 ينة تكرير النفط والغاز | الدراسات الصباحية ندسة العمليات النفطية

Fluid Statics Please provide a complete and readable solution for the problem if necessary and an explanation. Thank you!

Kindly Show the details of your solutions with Schematic and TS Diagrams with correct dimension analysis Plsss use metric system unit. Thanksss! ❤️?

5) Which statement is true about the friction factor in the Moody diagram (shown below). Moody Diagram 0.1 0.09 Transition Region 0.08 0.07 0.05 0.04 0,06 0.03 0.05 0.02 0.04 0.015 0.01 0.03 0.005 0.002 0.001 5x10-4 2x10-49 10-4 5x10-5 10-5 5x10-6 10-6 Friction Factor 12---- Laminar Flow 64 Material Concrete, coarse 0.25 0.025 Concrete, new smooth Drawn tubing 0.0025 Glass, Plastic Perspex 0.0025 Iron, cast 0.15 Sevens, old 3.0 0.1 Steel, mortar lined Steel, rusted 0.5 Stoel, structural or forgod 0.025 Water mains, old Friction Factor=AP. 1.0 Smooth Pipe 3000 10³ 10¹ 105 106 107 108 Reynolds Number, Re - Vd P a) The lines for different relative roughness in the turbulent regime correspond to Darcy-Weisbach model b) The lines for different relative roughness in the turbulent regime correspond to Nikuradse model c) The lines for different relative roughness in the turbulent regime correspond to Hazen-Williams model d) The lines for different relative roughness in the turbulent regime…

3. Shell T46 industrial lube oil has a viscosity of about 46.5cSt. What is its viscosity in terms absolute viscosity? Density if the oil is 804kg/m3. TNO L-Warning Oil Condition Viscosity 40 C Viscosity @ 100 t D-445 46.5 45.5 45.0 44.3 <39.87 D-445 CSt 7.0 6.9 6.9 6.8 <6.12 Oxidation E-2412 Abs 3.8 4.1 3.8 3.7 Nitration E-2412 Abs 2.6 2.6 0.04 2.6 0.04 2.6 0.11 TAN ng KONg 0.06 D-974 D-4739 ngKOH TBN

For my assigment, I was asked to design a electric motorbike that has a peformance equal to Honda CBR1000 Fireblade which has a petrol engine. A part of the the assignment is to calculate " An estimate of maximum Power your new motor will need to generate to match the Honda’s performance." I can make the assumption, apart from changing the motor, everything else is going to stay the same so the fairing,the rider and etc they're gonna be the same for the two bikes. So can you please tell me how I can calculate that which information would I need ?

Determine the critical speed for a vehicle with the following parameters; Parameter Value Units Mass 1,451 kg Wheelbase 2.57 Forward weight bias 45 Front axle cornering 67 kN/rad stiffness Rear axle cornering stiffness 67 kN/rad Provide your answer in units of (m/s) to 1 decimal place.

C Dynamic Analysis and Aeroelasticity SECTION B Answer TWO questions from this section ENG2012-N The moment of inertia of a helicopter's rotor is 320kg. m². The rotor starts from rest and at t = 0, the pilot begins by advancing the throttle so that the torque exerted on the rotor by the engine (in N.m) is modelled by as a function of time (in seconds) by T = 250t. a) How long does it take the rotor to turn ten revolutions? b) What is the rotor's angular velocity (in RPM) when it has turned ten revolutions?

Draw the three views, dimension using datum dimensioning