6 (2) Deniz(a) Design an Aryton (universal) shunt circuit to convert a basic PMMC meter with aninternal resistance of 10002 and a full-scale meter current of 50µA into a multi-range2amammeter with current ranges of 0-1mA, 0-10mA, 0-50mA, and 0-100mA respectively.(b) The Lissajous pattern observed on a CRO screen is shown in Figure 1. The frequencyratio isXXXXFigure. 1

Answered: Image /qna-images/answer/d0a679b5-f6a3-4a16-beda-e0aced313182.jpg

76612 (a) Design an Aryton (universal) shunt circuit to convert a basic PMMC meter with an internal resistance of 1000 and a full-scale meter current of 50µA into a multi-range 2 ammeter with current ranges of 0-1mA, 0-10mA, 0-50mA, and 0-100mA respectively. (b) The Lissajous pattern observed on a CRO screen is shown in Figure 1. The frequency ratio is XXXXX Figure. 1

76612 (a) Design an Aryton (universal) shunt circuit to convert a basic PMMC meter with an internal resistance of 1000 and a full-scale meter current of 50µA into a multi-range 2 ammeter with current ranges of 0-1mA, 0-10mA, 0-50mA, and 0-100mA respectively. (b) The Lissajous pattern observed on a CRO screen is shown in Figure 1. The frequency ratio is XXXXX Figure. 1

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter30: Dc Motors

Section: Chapter Questions

Problem 6RQ: What is CEMF?

See similar textbooks

Similar questions

A half-wave rectifier is needed to supply 15-V dc to a load that draws an average current of 250 mA. The peak-to-peak ripple is required to be 0.2 V or less. What is the minimum value allowed for the smoothing capacitance?
For the circuit in the figure, let V input = 8V, Ri = 12ohms, RL = 10ohms, and VZ = 3.3V. Determine the voltages and currents of the resistors and the current of the zener diode.
After replacing R5 with diode IN4007 (switch K3 to diode side) .What conclusion can you draw from analysis of this step ?
A clamper circuit has 20 Vp-p. 100Hz square wave input voltage. The circuit consists of silicon diode IN4001 and 3V battery as shown in Figure 1 C. 0.1 µF D R Vi(t) 50 k2 Vo(t) 3 V Figure 1 a) Find the output voltage for all input voltages values. b) Sketch the output waveform, Vo(t).
A half-wave rectifier is needed to supply 15-V dc to a load that draws an average current of 250 mA. The peak-to-peak ripple is required to be 0.2 V or less. What is the minimum value allowed for the smoothing capacitance? If a full-wave rectifier is needed?
The single-phase wave rectifier is used to charge a 200 V battery with an internal resistance of 0.2 as shown in the figure. SCRs are triggered by a steady dc signal. If SCR2 is made open circuit, what will be the average charge current?
In the circuit of the following figure, the input voltage Vs is 15 volts rms with a frequency of 60 Hz, R equals 150 Ohms and C equals 100,000 Pico Farads. The diodes are Germanium (Vd = 0.2 volts) and the Zener diode is 12 volts. a) The magnitude of the ripple voltage at Cb) The Magnitude of the Peak Inverse Voltage (PIV) for D1 and D2.
Power supply circuit is delivering 0.5 A and an average voltage 20 V to the load as shown in the circuit below. The ripple voltage of the half wave rectifier is 0.5 V and the diode is represented using constant voltage model. The smoothing capacitor value is equal to 220V ams 5OHZ İL-DC =05A RL VL-DC =20V
Power supply circuit is delivering 0.5 A and an average voltage 20 V to the load as shown in the circuit below. The ripple voltage of the half wave rectifier is 0.5 V and the diode is represented using constant voltage model. The smoothing capacitor value is equal to 220V rmsh soHz} VL-DC =20V 0.01 F 0.02 F 0.0167 F None of the above
a full-wave rectifier with a capacitor-input filter provides a dc output voltage of 35V to a 3.3k ohms load. Determine the minimum value of filter capacitor if the maximum peak-to-peak ripple voltage is to be 0.5V.
A single phase – half wave controlled rectifier with freewheeling diode is supplying a load consistingseries connected a resistor and an inductance from a 70.7V (RMS), 50Hz sinusoidal AC source.The firing delay of the thyristor is 90° and the load values are R=10Ω, L=0.1 H. Define the loadcurrent expression and draw the load current by calculating for first two periods. And calculate theaverage values of the load voltage and current.
Show the output voltage for the input voltage Vi in the figure by plotting it over a period. (Note: the diode used is a silicon diode and will not be considered ideal.)