} 8) A tensile load of 3000 N is applied to a steel bar of cross-sectional area 500 mm². If a tensile load was applied to an aluminum bar to achieve the same lateral (transvers) strain with the former (steel bar), what would be the load? Note: Original dimensions of the two bars are the same (Est = 2.1 x 105 MPa, Eat = 0.703 × 105 MPa, vg = 0.3, vat = 0.33) E = º , v = - Lateral Eaxial Fatuminum™ 3000 N A=500 mm? A=500 mm² Fatuminum™? 3000 N Steel Aluminum

} 8) A tensile load of 3000 N is applied to a steel bar of cross-sectional area 500 mm². If a tensile load was applied to an aluminum bar to achieve the same lateral (transvers) strain with the former (steel bar), what would be the load? Note: Original dimensions of the two bars are the same (Est = 2.1 x 105 MPa, Eat = 0.703 × 105 MPa, vg = 0.3, vat = 0.33) E = º , v = - Lateral Eaxial Fatuminum™ 3000 N A=500 mm? A=500 mm² Fatuminum™? 3000 N Steel Aluminum

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.3P: A tensile test was performed on a metal specimen having a circular cross section with a diameter 0....

See similar textbooks

Similar questions

A tensile test was performed on a metal specimen having a circular cross section with a diameter 0. 510 inch. For each increment of load applied, the strain was directly determined by means of a strain gage attached to the specimen. The results are, shown in Table: 1.5.1. a. Prepare a table of stress and strain. b. Plot these data to obtain a stress-strain curve. Do not connect the data points; draw a best-fit straight line through them. c. Determine the modulus of elasticity as the slope of the best-fit line.
What is the value of reduction factor of the beam, if the stress in the steel is 400 MPa, and the Modulus of Elasticity of the Steel is 200,000 MPa. O 0.671 0.692 O 0.660 O 0.650 None of the Choices O 0.681
5. A bronze bar is fastened between a steel bar and an aluminum bar as shown in Figure 5. Axial loads are applied at the positions indicated. Find the largest value of P that will not exceed an overall deformation of 3.0 mm, or the following stresses: 140 MPa in the steel, 120 MPa in the bronze, and 80 MPa in the aluminum. Assume that the assembly is suitably braced to prevent buckling. Use Est = 200 GPa, Eal = 70 GPa, and Ebr = 83 GPa. Steel A = 480 mm² 1.0 m Bronze A = 650 mm² 3P 4P 2.0 m FIGURE 5 Aluminum A = 320 mm² 1.5 m 2P
A 26-foot-long structural steel bar is being tensed along its centroidal axis. Point B is being tensed by 180 kips of force and point C is being tensed by 121 kips of force. The bar has a rectangular cross-section with a height of 3.6 inches and width of 2.8 inches. The steel is HSLC steel with a yield stress, oy = 50 ksi and modulus of elasticity, E = 30,000 ksi. Show all work and any assumptions clearly. Record your answers on the answer key. Complete the following: ): Calculate the axial stress in sections AB and BC of the beam. Does the calculated stress in either section exceed the yield stress of the steel? Calculate the deformation in sections AB and BC of the beam. What is the total axial deformation that the beam experiences? What is the final length of the beam? Calculate the factor of safety that this structural bar was designed for. w = 2.8 in. A B 180 k C 121 k Answer Key σ > Gy Yes or No * 18 ft 8 ft Axial Section Stress (ksi) AB BC Total Deformation, 8 (in) Final Length…
As shown in the figure below, a bronze bar is affixed between a steel bar and an aluminum bar. Axial loads are applied at the positions indicated. If the largest value of P that will not exceed an overall deformation of 4.0 mm, or the following stresses: 150 MPa in the steel, 130 MPa in the bronze, and 90 MPa in the aluminum. Assume that the assembly is suitably braced to prevent buckling. Use Est = 200 GPa, Eal = 70 GPa, and Ebr = 83 GPa. determine the stress in the bronze, steel, and aluminum
Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly connected between steel and bronze segments. What is the stress (in Mpa) in the bronze given that P= 188 kN? Express your answer in four decimal places.
PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D 10KN 0.8m 0.4m B 5KN 0.6m AL 20KN What is the deformation &pE in mm? A=800 mm² A=1,200 mm²
! Required information A steel bar (Es= 210 GPa) and an aluminum bar (Ea = 70 GPa) are bonded together to form the composite bar shown. 8 mm 8 mm 8 mm Aluminum 24 mm -Steel Determine the maximum stress in steel when the bar is bent about a horizontal axis, with M= 56 N.m. The maximum stress in steel is - MPa.
The modulus of elasticity of mild steel is equal to .. .? .... .. a. 2 x 10ʻN/m? a. 2 x 10'N/m 2 b. 2 x 10° N/m 4 c. 2 x 10 N/mm 5 d. 2 x 10 N/mm Check
8. If the modular ratio is equal to 11, and the Modulus of Elasticity of the Steel is 200,000 MPa. What is the value of fc'?
Compute the value the shear modulus G of steel whose modulus of elasticity E is 200 GPa and poisson's ratio is 0.30.
One of the following values is a possible for possion ratio for steel ? a. Zero b. one c. 0.3 d 0.9