8: A two stage telescopic cylinder is used to tilt the body of a lorry. When the lorry is fully laden, the cylinder has to exert a force equivalent to 40KN at all points in its stroke. The outside diameters of the tubes forming two stages are 75mm and 100mm. If the pump powering the cylinder delivers 12 l/min, calculate the extend speed and pressure required for each stage of the cylinder when tilting fully laden lorry.

8: A two stage telescopic cylinder is used to tilt the body of a lorry. When the lorry is fully laden, the cylinder has to exert a force equivalent to 40KN at all points in its stroke. The outside diameters of the tubes forming two stages are 75mm and 100mm. If the pump powering the cylinder delivers 12 l/min, calculate the extend speed and pressure required for each stage of the cylinder when tilting fully laden lorry.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

. Two identical cylinders are applied in series as shown in Fig.2. The cylinder piston and rod diameters are 80 mm and 40 mm respectively. The valve is working in position 2. Assuming the tank pressure is 1Bar. . In order to lift the mass 3000 kg in velocity of 0.1m/s, how much pressure in MPa are needed from the motor? • How much volume in liter/min are needed from the motor? 24p CA. ZAP Tips: Q=C₂4 P2 A2 P1 A1 A2 A1 Q1 Q2 MIHIXM Q3
- A centrifugal pump with an impeller diameter of 350mm and specific speed of 19.15 and requires 15 kW to discharge 2.4 m³ /min of water, and runs at 1800 rpm. Determine the discharge, head and power required when the pump runs at 2400 rpm. The same discharge could be obtained by altering the impeller diameter without changing the rotational speed for this case find the new diameter of the impeller the head and the power required.
The impeller of a centrifugal pump is 0.5 m in diameter and rotates at 1200 r .p. m . ; blades are curved back to an angle of 30⁰ to the tangent at outlet tip . If the measured velocity of flow at outlet is 5 m/ sec. If the pump is provided with whirlpool chamber which reduces the velocity of water by 50%. Kinetic energy converted into in whirlpool chamber in j/kg/sec And tangential velocity of runner at outlet
Answer the followwing problem: Determine the number of stages needed for a centrifugal pump if it is used to deliver 600gal/min of water and pump power of 15Hp. Each impeller develops head of 38ft. Calculate the compressor work in kJ required to compress 1 kg of an ideal gas from an initial volume and pressure of 0.65m3 and 101.3kpa to a final pressure of 517kpa & volume of 0.1943m3.ANS. 133.549 An air compressor takes air at 97kpa at the rate of 0.4m3/s and discharges to 650kpa. If power input to the compressor is 110kw, determine the heat loss(kw) in the compressor. ANS. 11.948
A Pelton wheel is supplied with 12 kg/s of water at 20 m/s. The buckets rotate on amean diameter of 250 mm at 800 rev/min. The deflection angle is 165o and friction is negligible. Determine the diagrampower.The output torque of the turbine is 26.5 Nm.The pressure drop over the nozzles is 2.45 bar gauge. Assume the water densityis 1000 kg/m3 . Calculate:1. Mechanical efficiency.2. Hydraulic efficiency3. Overall efficiency
Find an expression for the centrifugal force Fc if it depends on the mass m,the angular velocity w, and the radius R of an impeller.
This course A centrifugal pump with the following impeller dimensions is used to pump oil. The pump is running at 2500 rpm. CHide blocks b2 Boz 72 The parameters of the impeller are as follows: 1= 8cm, b1= 4cm, B1= 20° r2= 18cm, b2= 3cm, B2= 25° Take g= 9.81 m/s2 The velocity triangles at the inlet and the outlet are as follows V2 W2 W1 V1 U2 U1 Determine the outlet radial velocity in (m/s) Choose.., + Determine the theoretical head in (m) Choose.. Determine the volumetric flow rate in m/s Choose. 42 128 AM ENG A/23/2021
As a junior field engineer, you have been asked to assist a contractor in resolving the following problem. A 4.9 kW motor and gear drive rated at 175 rpm has been shipped with the four impeller blades listed below. The baffled rapid mix tank to which one of the impellers will be installed is 3.0 m² in volume (1.56 m diameter and 1.56 m depth). Assume water temperature of 10C, G= 1000s, water density = 1000 kg/m³, and motor power to water power transfer efficiency of 80%. Impeller options: A. Axial flow, 3 blades, diameter = 0.48 m, N₁-1.0 B. Axial flow, 3 blades, diameter = 0.61 m, Np=1.0 C. Radial flow, 6 blades, diameter = 0.48 m, Np=6.3 D. Radial flow, 6 blades, diameter = 0.61 m, Np 6.3 Answer the following: 3. What is the rotational speed (n) in rps? b. What is the power required in kW for impeller option A? What is the power required in kW for impeller option C? C. d. What is the power transferred to the water from the selected motor in kW? e. Which impeller should be used?…
In a pelton wheel, calculate the power available at the inlet and the hydraulic efficiency ofthe turbine. The wheel is having semi-circular buckets, which functions under a head of 150mand consumes 0.06 m3/s of water. The 750 mm diameter wheel turns 800 rpm. Assume thecoefficient of velocity as unity.
1.The engine has a given capacity of 60kw, calculate the power requirement in a hydraulic system tool , to know that the engine is capable to support the hydraulic system if a pump delivers 110 liters per minute and the pressure is 227bar.2.If the area of A1 = 0.05 m˄2 and the area of A2 = 1.5 m˄2 , external input force F1 = 50 N, then the external output force F2 ?
A Centrifugal pump is to discharge water at the rate of 110 lits/sec at the speed of 1450 rpm agalnst head of 13 m. Impeller diameter is 250 mm and its width is 50 mm. If manometric efficiency is 75%, determine vane angle at outer periphery.
a pump is delivering 160 liters per sec of water using an impeller diameter of 240 mm and operating at a speed of 1800 rpm. if the speed held constant and the impeller diameter is change to 203.2 mm, what is the new dischange og the pump in liters per second