8.12 The cylindrical pressure vessel with hemispherical end-caps is made of steel. The vessel has a uniform thickness of 18 mm and an outer diameter of 400 mm. When the vessel is pressurized to 3.6 MPa, determine the change in the overall length of the vessel. Use E = 200 GPa and v = 0.3 for steel. Neglect localized bending. 600 mm 400 mm FIG. P8.12

8.12 The cylindrical pressure vessel with hemispherical end-caps is made of steel. The vessel has a uniform thickness of 18 mm and an outer diameter of 400 mm. When the vessel is pressurized to 3.6 MPa, determine the change in the overall length of the vessel. Use E = 200 GPa and v = 0.3 for steel. Neglect localized bending. 600 mm 400 mm FIG. P8.12

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q1 . . A beam cross-section is subjected to an axial force P. Determine the application point of the load on the cross-section when the neutral axis passes through the points A and B as shown. Calculate P if the allowable normal stress is oallow 280 MPa. 15 cm 3 cm A 12 cm 3 сm Neutral axis B 3 cm
A solid shaft has 100 mm diameter. It is used to transmits 120 watt power at 200 rpm (Take G = 8 x 104 N/mm2). Determine the maximum intensity of shear stress induced (a) 0.288/ MPa (b) 2.81/ MPa (c) 0.20/ MPa (d) 20π MPa
The 39 kg drum is suspended from the hook mounted on the wooden frame. Determine the state of normal stress at point E on the cross section of the frame at section a-a. Use L = 71 mm. Express your answer in kPa. 50 mm 25 mm E Section a - a 0.5 m 0.5 m a O a D 1 m 1 m 1 m b B 30° A b LA 1 m 4 0
A tapered column assembly is made up from a square tubes having cross-sectional as shown in the figure. The axial loads PA=200KN and PB-850 kN are applied to the column at levels A and B. Evaluate the axial stress in segment BC of the column. Neglect the self-weight of the structure PA 150 mm, 1 = 12 mm (1) 150 mm PB B (2) 12 = 15 mm 200 mm 200 mm (a) (b)
STRESS IN THIN-WALLED CYLINDER Formulas: O = PD/2t + tangential Stress OL = PD/4t + longitudinal Stress Where: P = pressure inside the tank D= inside diameter of tank t= thickness of plate used for the cylinder PROBLEM 4: CE Brd Exam A 3m diameter x 6m high water tank is made up of 12mm thick steel plate. 4a. When full of water, find the circumfe-rential stress. а. 7.36 MPа c. 5.87 MPa b. 7.21 MPa d. 7.33 MPa 4b. When full of water, find the longitudinal stress. а. 4.29 MPa b. 4.05 MPa c. 2.66 MPa 4c. If plate stress is limited to 5 MPa, find the maximum height for said cylinder. a. 4.35 m c. 3.48 m d. 3.68 MPa b. 4.08 m d. 4.27 m
N-S 2 A flow of a viscous fluid with µ = 1.0 μ has a velocity distribution given by u = 0.9y - y². The shear stress at y = 0.45 m is 2 (a) 0.90 N/m² (c) Zero m (b) ∞ (d) - 0.90 N/m²
A 100- m steel tape is used to measure the distance of the line and found to be 1539.28- m long. During measurement, the tape is supported at the ends under a pull of 10- kgs and the observed mean temperature is 31°C. The tape is of standard length at 20 °C and a tension of 12- kgs. Thecross sectional area of the tape is 0.035 cm2. The coefficient of linear expansion is 0.0000116/°C and the modulus of elasticity of steel is 2.0 (10)^6 kg/ cm2. The tape weight is equal to 1.5- kg. a) Determine the total correction for temperature.b) Determine the total correction due to tension.c) Determine the total correction due to sag.d) What is the correct length of a line?
*84 The thin-walled cylinder can be supported in one of two ways as shown. Determine the state of stress in the wall of the cylinder for both cases if the piston P causes the inter- nal pressure to be 65 psi. The wall has a thickness of 0.25 in. and the inner diameter of the cylinder is 8 in. 8 in. (a) P 8 in. (b) P
8.5-14 A pressurized cylindrical tank with flat ends is loaded by torques T and tensile forces P (see figure). The tank has radius r = 50 mm and wall thickness = 3 mm. The internal pressure p = 3.5 MPa and the torque T = 450 N-m. What is the maximum permissible value of the forces P if the allowable tensile stress in the wall of the cylinder is 72 MPa? T P
5 - An aluminum circular shaft, fixed at both ends, is loaded by torques applied at points B and C, as shown in the figure. The bar material has a shear modulus G = 85 GPa. Plot the maximum shear stress and angle of twist along the length of the shaft. A D TB 0.5m Tc 0.9m с 0.4m 40mm ↑ TB-10KN-m Tc=15KN.m
41 O O On vo 11:14 Torsion Part 1.pdf → H.W.1: A solid circular steel shaft having an outside diameter of d= 0.75 in. is subjected to a pure torque of T = 650 lb-in. Deter- mine the maximum shear stress in the shaft. H.W.2: A hollow aluminum shaft with an outside diameter of 80 mm and a wall thickness of 5 mm has an allowable shear stress of 75 MPa. Determine the maximum torque T that may be applied to the shaft. H.W.3: A hollow steel shaft with an outside diameter of 100 mm and a wall thickness of 10 mm is subjected to a pure torque of T= 5,500 N-m. (a) Determine the maximum shear stress in the hollow shaft. (b) Determine the minimum diameter of a solid steel shaft for which the maximum shear stress is the same as in part (a) for the same torque T. 26 H.W.4:A solid 0.75-in.-diameter shaft is subjected to the torques shown in Figure freely. - The bearings shown allow the shaft to turn (a) Plot a torque diagram showing the internal torque in segments (1), (2), and (3) of the shaft. Use…
The beam shown is hinged at one end. It is supported by two steel rods of equal length of 1.5m. Before the load is applied, the beam hangs level. Use E = 200, 000MPa and = 11.7 um Neglect bending of the beam. m°C A=640mm2 A=320mm2 A 1.2 m 0.8 m 1.2m 54KN What is the stress of rod C if there is no change in temperature in MPa?