9.) The flow work relation (Wflow) is the same whether the fluid is pushed into or out of the control volume. Select one: True False 3.) For single stream devices like nozzles, the velocity usually become larger at the exit compared to the inlet that it also increases the pressure of the fluid flow. Select one: True False

9.) The flow work relation (Wflow) is the same whether the fluid is pushed into or out of the control volume. Select one: True False 3.) For single stream devices like nozzles, the velocity usually become larger at the exit compared to the inlet that it also increases the pressure of the fluid flow. Select one: True False

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The fan/blower installed in the central air conditioning system is of the axial flow type. This function is to help air circulation in the cooling process in the cooling tower. Atmospheric air enters a fan/blower and its pressure increases, so that the air total pressure leaving the blower is 110.29 kPa. Calculate: a) Blower total pressure? b) Speed of the air leaving the blower?
1) A pipe carries water from the bottom of a pool to the top of a water slide with the aid of a pump. The pool is 3 meters deep and the water slide is 5 meters above the surface of the pool. The pipe carrying the water has uniform area. A diagram of the system is shown here. Open to atmosphere Pump Pool a) If the pump's output is 62 kJ/m³ and the flow rate is 0.3 m³/s, what is the resistance in the pipe? b) The pool is partially drained for construction. How low can the water go in the pool before the water in the pipe stops flowing? c) After long use, sediment builds up in the pipe, increasing the resistance and decreasing the area of the pipe uniformly. How do these changes affect the current in the pipe?
Question 1 (Pumps, pumping and water clarification) 1.1 List five different ways in which the pumping of fluids can be accomplished. 1.2 In a winze inclined at 30° to the horizontal, 36 kilolitres per hour must be pumped through a column of 300 m from the bottom to the top of the winze by means of a centrifugal pump. Assume the following: • Velocity is not to exceed 1,5 m/s • Coefficient of pipe friction = 0,01 • Pump and drive efficiency = 78% • Motor efficiency = 90% Determine: a) the size of column required b) the power of the electric motor to drive the pump
The diameter of the discharge pipe of a boiler feed pump is 4 inches and the suction pipe is 6 inches. The water delivered is 250 gpm and the temperature is 60 ºF. The discharge pressure near the pump is 190 psig and the suction is 12 inches Hg vacuum. Determine the following: a) Discharge velocity in ft/sec. b) Suction velocity in ft/sec. c) Suction pressure in psi. d) Find the total dynamic head if the discharge gage is located 3 ft above pump centerline and vacuum gage connection to the suction pipe is 2 ft below the center of the pump. Assume that the head necessary to overcome the frictional resistance through the pump is 2.2 ft.
State the Heads of Pumps *
Answer this ASAP,thx In a gas turbine, air enters the compressor at a temperature of 290 K and a pressure of 100 kPa with a mass flow rate of 6 kg/s. The system pressure ratio is 10 and the exit temperature of each turbine stage is 1400 K. The efficiency of the compressor and turbine is 70% while the effectiveness of the regenerator is 70%. Value of K = 1.4, calculate A) thermal efficiency B) workback ratio C) net power generated
i. A wind turbine has the following data: Downstream wind velocity = 9 m/s Upstream wind velocity =18 m/s Rotor Power output = 1 MW a. Compute the wind rotor efficiency. b. Calculate power in the wind and the length of the rotor blades ii. ComparethedifferenttypesBiogasplants?
V:32) The jet on a water feature shoots a column of water 75 ft. high. The nozzle is located just above the surface of a reflecting pool and has a diameter of 2 in. A submersible pump with a 4 in dia outlet and an 8 in. diameter intake pipe located 3.25 ft. below the surface of the pool operates the jet.1. Write an expression to determine the velocity of the water coming out of the nozzle.2. Find the velocity of the water at the nozzle exit.3. Find the velocity at point A just inside the inlet.
Prototype of a mixed flow mini heart support pump at n1= 11000 rpmthe manometric pressure height is 100 mmHg, the flow rate of the blood-like liquid it pumps is 5.5 l/min and the efficiency is 9%. The relative density of this liquid is 1.06. It can be assumed that yields have not changed.a) find the power of the pump at this speed (n1).b) if the speed of this pump is reduced to n2 = 8000 rpm, what is the flow rate, manometric pressure height and power?
1. Using the Steam Tables, determine the heat absorbed by the boiler (KW) and Wsf when subcooled water at pressure = 5 Mpaa (subcooled by 64 deg C measured at the boiler inlet), is superheated to 100 degrees SH at the same pressure. Flow rate is at 10 cubic meters per minute. Ans.: a) Qa = b)Wsf= Hint: Use v at compressed water temp. at boiler inlet to convert to mass flow rate. Process is isobaric (Constant Pressure, where Q=m x AH).
A reciprocating compressor is operating at 800RPM. Suction pressure and discharge pressure are held constant by other means that have nothing to do with the compressore . The speed is increased from 800 - 840 Rpm (a 5% increase) a) What is the change in the flow rate through the compressor? b) What is the change in the pressure rise through the compressore? c) What is the change in the power that must be delivered to the compressor?
Q3: The Petroco Service Station has one pump for regular unleaded hour. gas, which (with an attendant) can service 10 customers per Cars arrive at the regular unleaded pump at a rate of 6 per hour. Determine the average queue length, /the average time a car is in the system, and the average time a car must wait. If the arrival rate increases to 12 cars per hour, what will be the effect on the average queue length?