A 1.00 liter solution contains 0.31 M ammonia and 0.40 M ammonium perchlorate. If 0.200 moles of potassium hydroxide are added to this system, indicate whether the following statements are true or false. (Assume that the volume does not change upon the addition of potassium hydroxide.) A. The number of moles of NH3 will remain the same. True False B. The number of moles of NH4+ will increase. ⒸC. The equilibrium concentration of H3O+ will increase. ⒸD. The pH will remain the same. ⒸE. The ratio of [NH3] / [NH4*] will remain the same.

A 1.00 liter solution contains 0.31 M ammonia and 0.40 M ammonium perchlorate. If 0.200 moles of potassium hydroxide are added to this system, indicate whether the following statements are true or false. (Assume that the volume does not change upon the addition of potassium hydroxide.) A. The number of moles of NH3 will remain the same. True False B. The number of moles of NH4+ will increase. ⒸC. The equilibrium concentration of H3O+ will increase. ⒸD. The pH will remain the same. ⒸE. The ratio of [NH3] / [NH4*] will remain the same.

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter4: Types Of Chemical Reactions And Solution Stoichiometry

Section: Chapter Questions

Problem 47E

See similar textbooks

Similar questions

Calcium carbonate, CaCO3, can be obtained in a very pure state. Standard solutions of calcium ion are usually prepared by dissolving calcium carbonate in acid. What mass of CaCO3 should be taken to prepare 500. mL of 0.0200 M calcium ion solution?
. Which of the following will affect the total amount of solute that can dissolve in a given amount of solvent? a. The solution is stirred. b. The solute is ground to line particles before dissolving. c. The temperature changes.
. Why does the amount of excess solid solute present in a solution not affect the amount of solute that ultimately dissolves in a given amount of solvent?
Graph Table 14.10 shows solubility data that was collectedin an experiment. Plot a graph of the molarity ofKI versus temperature. What is the solubility of KI at55°C?
Calculate the percent by mass of KBr in a saturated solution of KBr in water at 10 °C. See Figure 11.17 for useful data, and report the computed percentage to one significant digit.
Which of the following will affect the total amount of solute that can dissolve in a given amount of solvent? a. The solution is stirred. b. The solute is ground to fine particles before dissolving. c. The temperature changes.
Addition of water to concentrated sulfuric acid is dangerous because it generates enough heat to boil the water, causing it to spatter out of the container. For this reason, chemists remember to add acid to water. In a dilution experiment, we calculate the amount of the more concentrated solution that must be measured out. If we place this concentrated solution (Figure 4.7) in the volumetric flask first, then dilute with water, we violate the caution Add acid to water. Describe a safer variation on the method shown in Figure 4.7 that allows the quantitative dilution of concentrated sulfuric acid. Figure 4.7 Preparing a dilute solution from a concentrated solution. (a) Draw the concentrated solution into a pipet to a level just above the calibration mark. (b) Allow the liquid to settle down to the calibration line. Touch the tip of the pipet to the side of the container to remove any extra liquid. (c) Transfer this solution to a volumetric flask. Again touch the pipet to the wall of the flask to ensure complete transfer, but do not blow out the pipet because it is calibrated for a small amount of liquid to remain in the tip. (d) Dilute to the mark with solvent. Frequently, especially with concentrated acids, it is best to have some solvent present in the volumetric flask before you add the concentrated sample.