A 5-m long simply supported timber beam carries two concentrated loads, as shown in Figure P .The cross-sectional dimension of the beam are shown in Figure F (a) At section a-a, determine the magnitude of the shear stress in the beam at point H. (b) At section a-a, determine the magnitude of the shear stress in the beam at point K. (c) Determine the maximum horizontal shear stress that occurs in the beam at any location within the 5-m span length. (d) Determine the maximum compression bending stress that occurs in the beam at any location within the 5-m span length. " 14 kN 42 KN 0.5 m 150 mm ↓ H 450 mm

A 5-m long simply supported timber beam carries two concentrated loads, as shown in Figure P .The cross-sectional dimension of the beam are shown in Figure F (a) At section a-a, determine the magnitude of the shear stress in the beam at point H. (b) At section a-a, determine the magnitude of the shear stress in the beam at point K. (c) Determine the maximum horizontal shear stress that occurs in the beam at any location within the 5-m span length. (d) Determine the maximum compression bending stress that occurs in the beam at any location within the 5-m span length. " 14 kN 42 KN 0.5 m 150 mm ↓ H 450 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Two pieces of lumber having square section (b x b) are arranged and supported as shown. The horizontal lumber is hinged at the left and free at right. The right end carries a concentrated load P. The vertical lumber supports the horizontal lumber at the midspan. Find the following: a) maximum shear stress, b) maximum bending stress, and c) maximum compressive stress. P Hinge DATA FOR PROBLEM 1 b b (N ) (m ) (m m ) (m m ) 6 5040 1.38 146 146
A cantilever wood beam consists of eight 2 in. thick planks glued together to form a cross section that is 16 in. deep. Each plank has a width of b - 4.3 in. The cantilever beam has a length of L- 5.9 ft and it supports a concentrated load of P- 3500 Ib. (a) Calculate the magnitude of the horizontal shear stress at points A, B. C, and D. (b) From these results, plot a graph showing the distribution of shear stresses from top to bottom of the beam. 2 in. (typ) B D 16 in. Answer: TA i psi Te-i psi TC-i psi TD- i psi Save for Later Attempts: 0 of 1 used Submit Answer
A 12.4-ft-long simply supported timber beam carries a 11.2- kip concentrated load at midspan. The cross-sectional dimensions of the timber are shown in the second figure. (a) At section a-a, determine the magnitude of the shear stress ?H in the beam at point H. (b) At section a-a, determine the magnitude of the shear stress ?k in the beam at point K. (c) Determine the maximum horizontal shear stress ?max that occurs in the beam at any location within the 12.4-ft span length. (d) Determine the maximum tension bending stress ?max that occurs in the beam at any location within the 12.4-ft span length. 3.9 1.4. 1.2.4 H a a 6.2 16 11.2kips 7.8 Dimensions in inche 6.2 x
A simply supported 4-m long beam is made up of 80% grade Malugai. The beam is carrying a uniform load of 10 KN/m all through out its length and a concentrated load of 500 N at the midspan. The cross-sectional area of the beam is indicated below. What is the actual bending stress of the beam in MPa? (use two decimal places, no need for unit) What is the actual shearing stress of the beam in MPa? (use two decimal places, no need for unit)
For the cantilever beam shown. find the value of Normal stress due to axial load at :point F FO ce A 10 m Diameter 100 mm 6 KN.m No stresses at point D 0 -31.229 Mpa +40.99 Mpa -0.25 Mpa +40.49 Mpa No stresses at point F No stresses at point A No stresses at point B +0.25 Mpa +40.74 Mpa No stresses at point C -40.99 Mpa +31.229 Mpa -40.74 Mpa +30.55 Mpa -40.49 Mpa +0.679 Mpa -0.679 Mpa No stresses at point E -30.55 Mpa
A beam has a rectangular cross- section and is subjected to the resultant internal loadings shown 73.3 MPa 10.1 MPa zero B 27.5 MPa A C D 250 N.m 5 kN Determine the normal stress at point D caused by the 250 N.m bending moment (1= 5.46X 10-8) 8 kN 22 mm 20 mm 32 mm
1. What is the maximum shearing stress (fv) of the beam? (in MPa) 2. What is the maximum flexural stress (fb) of the beam? (in MPa)
2. A beam with an inverted U section is loaded as shown. What is the max flexural stress developed and the max beam shear developed in the beam? 30mm 30mm 2m 6m 2m 200m 250mm 40mm
60 mm 150 mm 60 mm 300 mm 600 III 60 mm 150 m
Given a cantilever beam with given loadings and cross-section as shown in the figures, what is the absolute value of the maximum flexural shear stress? In Mpa (avoid truncation in the middle of solution and do not round off anything) help asap. Thank you
A simply supported wood beam with overhang is subjected to uniformly distributed load q. 9 1m- 250 mm 200 mm i The beam has a rectangular cross section with width b = 200 mm and height h = 250 mm. Determine the maximum permissible value q if the allowable bending stress is all = 11.8 MPa, and the allowable shear stress is Tall = 1.95 MPa. (Enter the magnitude in kN/m.) kN/m Need Help? m Read It
From the given truss shown, compute the stress at section CE. The truss has a uniform diameter, inner diameter is 70 and outer diameter is 100 mm.