A balanced three-phase 250-V source supplies a balanced three-phase load. If the line current I is measured to be 25 A and is in phase with the line-to-line voltage, VBC, find the per-phase load impedance if the load is (a) Y-connected, (b) A-connected. You may assume phase sequence to be a-b-c.

A balanced three-phase 250-V source supplies a balanced three-phase load. If the line current I is measured to be 25 A and is in phase with the line-to-line voltage, VBC, find the per-phase load impedance if the load is (a) Y-connected, (b) A-connected. You may assume phase sequence to be a-b-c.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.42P: A balanced -connected impedance load with (12+j9) per phase is supplied by a balanced three-phase...

See similar textbooks

Related questions

Q: Find the Norton equivalent with respect to the terminals a, b for the circuit in (Figure 1). Suppose…

A: Step 1 Given that: vs=87 V, and R= 14 ohm. The circuit is shown below. Calculate Norton’s…

Q: What are the functions of a sensor? Explain the function of on delay timers. Explain the working…

Q: You are given with the following information about a pn junction with very high doping of acceptor…

Q: A network containing 50 buses in which 10 are the voltage control buses, 6 are the generator buses.…

A: Given, Total number of busses, n = 50. Voltage control bus = 10. Generator bus = 6.

Q: g(t)=sinc(t) g(t)=2t^2-3t+6/1-t Find: Odd and even part

A: Given signals are i) g(t)=sinc(t) ii) g(t)=2t^2-3t+6/1-t We need to find even and odd parts of the…

Q: A 25 kW, 240 V self excited dc shunt generator has a field circuit resistance No Units! f 62.50, and…

A: Load current= power outputterminal current Amps. Given power output= 25 Kw = 25000 W . Terminal…

Q: x Problem 5. Which of the following corresponds to the periodic signal shown in the plot! not…

A: The signal has an average value .i.e. a0. From the figure, a0=1.

Q: In the circuit below, the switch closes at t = 0. Determine the output voltage, vo(t), across the…

A: We need to find out the voltage across capacitor for given circuit .

Q: 1. A voltage source is given as v(t) = 13 cos(8nt-45°). a. What is the amplitude of the voltage? b.…

A: Given that voltage source is as follows V(t) = 13 cos(8πt-45°)

Q: Find the power factor 4Ω Μ -j2Ω j5Ω -j2Ω Ans : pf = 0.555 (leading)

Q: *** . . V1 9 V. ** R1 10KQ R3 1.0KQ ** … * * R5 >1.0kQ . W 1.0KQ R4 1.0KQ * ***** *** V2 12 V.

Q: 12. A system is described by y[n] + 1.8y[n − 1] + 1.62[n - 2] = x[n]. Classify this system as to…

A: Given- System is- yn+1.8yn-1+1.62yn-2=xn To find- Linearity, time invariance, BIBO stability,…

Q: The total voltage of a series connected batteries with values of 12 V, 13 V and 18 V. 4.6337 V 25 V…

Q: Simplify the Boolean expression [AB(C+BD) + ABCD.

A: We need to find out the simplified Boolean expression for given expression for given function

Q: For the op-amp shown in the following figure, the voltage gain is equal to------- 80 ΚΩ Vino 3 ΚΩ

A: Given data, Circuit diagram is given as,

Q: Over what band of frequencies will a 100 MHz carrier modulated at 5 kHz extend?

A: Given data- Carrier wave frequency=100 MHz, Modulated frequency=5 kHz, To Find- The band frequencies…

Q: What is the value of critical frequency (MHz) if a signal radiated from transmitting antenna has an…

A: Given here MUF=10 MHz and angle of elevation = 33° we need to find the critical frequencyin MHz.

Q: An op amp has an input offset voltage of 4.3 mV. It is used in an inverting amplifier whose gain is…

Q: Compute the eight-point circular convolution for the following sequences. (a) x₁(n) = {1, 1, 1, 1,…

Q: t is the frequency at which the magnitude of the output becomes 0.707 of the maximum. A) CUT OFF…

Q: The total input power measured by a two-wattmeter is 40 kW. Calculate the power factor if one…

A: Given, Total input power measured by wattmeter, PT=40 kW,W1+W2=40 kW. First wattmeter reads, W1=15…

Q: The capacitor in the circuit below has an initial voltage of 10 V across it, i.e., v(0)=10V. The…

A: Given- Voltage = 5 V Resistance = 1 k-ohm Capacitance = 1μF Initial voltage of capacitor v(0)= 10…

Q: Find the number of strands of ACSR conductor for 3 layer transmission line?

A: Given: ACSR conductor with number of layer, n = 3.

Q: Find the modulation index of a 20 V carrier is amplitude modulated by three different frequencies…

A: It is given that: AC=20 VAm1=1 VAm2=2 VAm3=3 V

Q: - Two sinusoidal EMFs are given as e₁ = Asin (wt + 4) and e2 = B sin(wt – 77 ) The phase difference…

A: Given, Two sinusoidal emf equation as, e1=Asinωt+π4.e2=Bsinωt-π6.

Q: Problem 3 Use a 3x8 decoder to implement the following Boolean function: F = bc + abcd + abc

Q: 2. Dertemine Req using delta-wye transformation. Req 10122 5 100. 2012 552 M 1552 25-22

A: We need to determine the Req using wye delta transformation.

Q: 15V| + 10Ω yo 501 V €33Ω ΎΣΩ + {20 Ω Υ Σ 40 Ω

A: Given: Required: V0

Q: Use the mesh-current method to find the branch currents ia-ie for the circuit shown in (Figure 1).…

Q: 2. Solve for the Mesh Currents and Vx.

A: The required parameters can be calculated by using the mesh analysis. The mesh equation can be…

Q: Determine I, Io and Vo 12V (+1) 4Ω α 6Ω +201 να ΕΞΩ 3

Q: A 25 kW, 240 V self excited dc shunt generator has a field circuit resistance of 62.5 02, and an…

A: Given, Power, P=25 KW field winding resistance, Rf=62.5 Ω armature winding resistance, Ra=0.05 Ω…

Q: =E₁ 2=E2 Vb 4.7k-2 Vab IRY E₁ lov V₂ V₂ 19 22kn b (12) R4 Parameter / Computed Va lok Eskrrr 33k-2…

Q: Using partial fraction expansion method for complex repeated poles, find the inverse Laplace…

Q: Problem 4.12 (Node-Voltage Method) Find V₁, V₂, V₂, and vb vel 144 V + 4Ω V 80Ω Υ ανάλο γάξ 10 Ω Ων…

A: We need to find out the node voltage for given circuit, we will use nodal analysis .

Q: 2- Design a 4-bit DAC assuming high voltage of 3.5 V and a Vee of 12 V? determine the output voltage…

Q: A 550V, 75 KW long shunt, DC compound generator has a series field resistance of 0.020, a shunt…

Q: 2. What is the voltage loss (potential difference) in the entire circuit? Are the two resistors…

Q: 3.23 An LTI system is characterized by the system function H(2) (a) Determine the impulse response…

Q: For the circuit below, assume the diodes operate with a constant voltage drop of .7V, find Vx, Vy,…

Q: 5. If a diode has a current-voltage relation of I = 10-14 (e40v-1), what is the diode voltage when…

A: Given: A diode has voltage current relation as, I=10-14e40V-1. The current is I=150 mA.

Q: Suppose a 0.3 m long solenoid with cross-sectional area of 12 cm 2, N 1 = 1400 turns and N 2 = 20…

A: Given: Length of solenoid L=0.3 m, Cross-sectional area A=12 cm2, N1=1400 turns, N2=20 turns. L1=0.1…

Q: The purpose of the Zener diode is to maintain the voltage across the load at 10 V. The maximum power…

A: We need to find out the value of resistor for given load power in given circuit

Q: Draw the complete logic diagram from the given logic equation, maximum of 2 inputs per gates used.…

A: Given: F=X'YZ+XY'Z+(XZ')' To do: We have to draw the logic diagram from the given logic function.…

Q: raw the complete logic diagram from the given logic equation, maximum of 2 inputs per gates used.…

Q: A cable having resistance 'R' was cut into 10 equal pieces. It was then connected in parallel, R/10…

Q: Calculate the current flowing in a 50 mH - inductor if the energy stored in its magnetic field is…

A: We need to find out the current through inductor for given energy

Q: In the network below, find the power associated to the current source, for V1 - 8 V. V1 + 24 Select…

A: Given data, V1=8 V. Circuit diagram is given as,

Q: Μ 20 Ω 40 Ω Τ 10 Ω 30 Ω Τ Μ Μ 15 Ω 15Ω Μ 15Ω • 20 Ω Μ

A: First we will do delta to star conversion for given circuit then by using of series parallel…

Q: Calculate the complex impedance of the following components at 25kHz. R1 100 +i C1 15 nF

A: Given elements, Frequency, f=25 kHz.

Concept explainers

Single Phase AC Circuit

Alternating Current (AC) is a type of electric power in which the electric current changes, both in magnitude and direction, at regular intervals. This AC Circuits can deliver power in either a Single Phase system or a Three Phase system.

Question

100%

A balanced three-phase 250-V source supplies a balanced three-phase load. If the line current IA is
measured to be 25 A and is in phase with the line-to-line voltage, VBC, find the per-phase load
impedance if the load is (a) Y-connected, (b) A-connected. You may assume phase sequence to be a-b-c.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Analysis of Single Phase and Three Phase System

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

3. The single-line diagram of a three-phase power system is as shown in Figure Al-3. Impedances are marked in per unit on a 100-MVA, 400-kV base. The load at bus 2 is S2 = 15.93 MW – j 33.4 Mvar, and at bus 3 is S3 = 77 MW +jl4 Mvar. It is required to hold the voltage at bus 3 at 40020° kV. Working in per unit, determine the voltage at buses 2 and 1. V2 V1 V3 j0.5 pu j0.4 pu S2 S3 Figure A1-3
A three-phase system has balanced conditions so that the per-phase circuit representation can be used as shown in Figure 1 Select the turns ratio of the step-up and step-down transformers that the system operates with an efficiency greater than 99 percent. Moreover, find the complex power (received or given) of all components in the circuit and the V1 and V2 voltages. The load voltage is specified as 4 kV rms, and the load impedance is 4/3 ohm. ..
The Figure shows a balanced Y-A 3Ø circuit. The phase voltages of the Y-connected source are V, = 11020°, V, = 1102 - 120° and V. = 1102120°, Volts. The line impdedances are Z,=10+j5 Q each. The impedances of the A-connected load are ZA = 75+j255 N each. Determine: Line Currents, Phase Currents (load), Power drawn by the load. Ve ZA Vb
Please help with this balanced three-phase circuit problem.
1. Calculate the line currents for phase a, b and c.2. Calculate the line-to-neutral voltages at the load for phase a, b and c.3. Draw the phasor diagram of the source line-to-neutral voltages and line currents.
2. A single-phase are distributor AB is fed from end A and has a total impedance of (0.3-0.3) ohm. At the far end, the voltage V-240V and the current is 100A at a p.f. of 0, 8 lagging. At the mid-point M. a current of 100 A is tapped at a p... of 0.6 lagging with reference to the voltage V_{M} at the midi-point. Calculate the supply voltage V Lambda j sending current I_{N} and the phase angle between V_{A} and V_{E}
Problem 1 - Series en Parallel AC networks [19] Look at the circuit in Figure 1 and determine the following: (a) Total Admittance. (b) Total Impedance. (c) Total Current (l:). (d) Current (I1) through impedance Z2. (e) Current (12) through impedance Z3. (f) Current (I3) through impedance Z4. (g) Is this an inductive or capacitive circuit? A. B Zs 220V;50HZ Figure 1 (h) Voltage across Z1. (i) Voltage across A and B. G) Voltage across Zs. Z1 = 3 + j5 ohm Z2 = 10 + jo ohm Z3 = 5 + j15 ohm Z4 = 10 – j30 ohm Zs = 20 – j30 ohm Admittance and Impedance in rectangular notation. All currents and voltage in polar notation. Take voltage as reference.
2) The one-line diagram of a three-phase power system is as shown in Figure. Impedance are marked in per-unit on a 100-MVA, 400-kV base. The load at bus 2 is S2=15.93 MW - j33.4 Mvar, and at bus 3 is S3-77 MW + j14 Mvar. It is required to hold the voltage at bus 3 at ...L0 kV. Working in per-unit, determine the voltage at buses 2 and 1. (Please determine the voltage magnitude within the specified limits: 410-450 V. By considering the voltage magnitude value you determined yourself, solve the question.) V₁ j0.5 pu V₂ j0.4 pu S₂ Figure V3 S3
In a two-phase circuit, find the unbalance factor of the load voltage when one wire is disconnected. Here, the unbalance factor is a value expressed as V2/V, or I/I, when expressed as a symmetric component.
In Figure 1, the 3-phase source has a line-to-line voltage of 440 volts. The details of the impedances are the following: Z₁ = 36-j15; Z₂ = 40 + /300; Z₂ = 45+j60 ; Z₂ = 75 + jo ; Z5 = 50+j50; Z6 = 20+ j48 2. Determine the following: (a) Line currents: labi, and I (c) Line currents: lar, Ibr, and ICT; (b) Line currents: Iaz, Ibz, and Iczi (d) PT, QT, ST, and pft for the system; (e) W, and W, readings for 2-wattmeter method at lines a and b. Balanced 3-Phase ab-bc-ca source C Figure 1 →laT -Ibr -KT 1 lal ²3 ↓ Ibi 1 Ici la2 lb2 le2ܝ 150 1²₂ OND
A three-phase circuit is balanced. The source voltage for the a-phase has a magnitude of 100 volts, and you can assume the phase angle is a reference of 0 degrees. Write the phasor expressions with proper subscript notation for the source voltage for each leg of the three-phase source if it is in a positive phase sequence.
4. Three-phase circuit