A beam carries a uniform distributed load of intensity w in N/m. It was determined that Vmax = 7.5w N, (+)Mmax = 5.2w N-m, (-)Mmax = 4.5w N-m. From the given cross section shown, ytop = 64.183 mm, ybot = 135.817 mm, and INA = 25.059 x 10 6 mm4. The allowable stresses are as follows: σfT = 30 MPa, σfC = 60 MPa, and τ = 10 MPa. a. The safe uniform load considering tensile flexural strees is _____N/m b. The safe uniform load considering compressive flexural stress is _____ N/m. c. The moment inertia of the area about the neutral axis is _____ mm^3.

A beam carries a uniform distributed load of intensity w in N/m. It was determined that Vmax = 7.5w N, (+)Mmax = 5.2w N-m, (-)Mmax = 4.5w N-m. From the given cross section shown, ytop = 64.183 mm, ybot = 135.817 mm, and INA = 25.059 x 10 6 mm4. The allowable stresses are as follows: σfT = 30 MPa, σfC = 60 MPa, and τ = 10 MPa. a. The safe uniform load considering tensile flexural strees is ___N/m b. The safe uniform load considering compressive flexural stress is _ N/m. c. The moment inertia of the area about the neutral axis is ___ mm^3.

Automotive Technology: A Systems Approach (MindTap Course List)

6th Edition

ISBN:9781133612315

Author:Jack Erjavec, Rob Thompson

Publisher:Jack Erjavec, Rob Thompson

Chapter3: Basic Theories And Math

Section: Chapter Questions

Problem 23RQ: When applying the principles of work and force, work is accomplished when force is applied to an...

See similar textbooks

Similar questions

2M 55° 20N 30N 45° 60N 70N
28 cm a? 100 cm 30° 15 cm
P1.60 A block of weight W is being pulled over a table by another weight Wo, as shown in Fig. P1.60. Find an algebraic formula for the steady velocity U of the block if it slides on an oil film of thickness h and viscosity u. The block bottom area A is in contact with the oil. Neglect the cord weight and the pulley friction. Assume a linear velocity profile in the oil film.
100 mm В A 30 mm
1 0 Calculate the total volume of the cylindrical component below (not to scale): L1 D1- D1 = 1.12 cm D2 = 0.71 cm D3 = 1.58 cm L1 = 18.68 cm L2 = 15.36 cm L3=13.77 cm L4 = 9.77 cm Answer: Check L2 L3 L4 D2- What is the volume of the cylindrical component? (State your answer in S.I. units (m³), accurate to 3 significant figures) D3
Express the quantity 30.6×10^−4m in mm
The coefficient of bend value is the energy loss due to bend in a pipe depends on the pipe diameter, & radius of curvature of bend. O Bend pipe material O Length of the bend pipe O Angle of bend O Friction in the pipe bend
F-90016 F₂=600% F₁=96016 30° ·x Part A Determine the magnitude of the resultant force acting on the corbel. Express your answer in pounds to three significant figures. ▸ View Available Hint(s) 15| ΑΣΦ 41 Ivec FR = Submit Part B 0= Determine the direction of the resultant force acting on the corbel measured counterclockwise from the axis. Express your answer in degrees to three significant figures. ► View Available Hint(s) IVE| ΑΣΦ | | vec ? ? lb 0
Calculate to the correct number of significant figures. (3.14x2.4367) - 2.34
I’m struggling with questions q1 2 3 4 5
Ixo and Iyo of a quarter circle with a diameter of 50cm (Answer format: Ixo= , Iyo=)
Q1. As shown in the image below, the force acting on the box is F = (C.s²) N, where constant C = 2 and s is displacement in m. S Determine the work done by force ♬ to the box when the box has displaced s = 1.2 m. Please pay attention: the numbers may change since they are randomized. Negative sign must be included if the work done is negative. Your answer must include 2 places after the decimal point, and proper Sl unit. 1 F Your Answer: Answer units S