A beam of T-section is pin-joint supported at point A and simply supported at point B with an overhang section BC shown in Figure 2. The cross section has the width b-65 mm, height h 75 mm and thickness / -13 mm. (a) Determine the support reactions at points A and B. (b) With the aid of bending moment of diagram, determine the maximum tensile and compressieve stresses in the beam.

A beam of T-section is pin-joint supported at point A and simply supported at point B with an overhang section BC shown in Figure 2. The cross section has the width b-65 mm, height h 75 mm and thickness / -13 mm. (a) Determine the support reactions at points A and B. (b) With the aid of bending moment of diagram, determine the maximum tensile and compressieve stresses in the beam.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Rigid bar ABCD is loaded and supported as shown. Steel [E = 30000 ksi] bars (1) and (2) are unstressed before the load P is applied. Bar (1) has a cross-sectional area of 0.75 in.2 and bar (2) has a cross-sectional area of 0.425 in.2. After load P is applied, the strain in bar (1) is found to be 780 μs. Assume L₁-60 in., L₂=90 in., a=40 in., b=40 in., and c-30 in. Determine: (a) the stresses in bars (1) and (2). (b) the vertical deflection vp of point D on the rigid bar. (c) the load P. A Answers: (a) 0₁ = (b) VD= (c) P = i i i L₁ a L2 in. (2) ksi, 0₂ = i kips. C D P ksi.
The rigid bar AB of negligible weight is supported by a pin at O. When the two steel rods are attached to the ends of the bar, there is a gap A = 4 mm between the lower end of the left rod and its pin support at C. %3D Compute the stress in the left rod after its lower end is attached to the support. The cross-sectional areas are 300 mm2 for rod AC and 250 mm? for rod BD. Use E = 200 GPa for steel. A В 0.75 m 1.5 m > 2 m D
Rigid bar ABCD is loaded and supported as shown. Steel [E = 29900 ksi] bars (1) and (2) are unstressed before the load P is applied. Bar (1) has a cross-sectional area of 0.73 in.² and bar (2) has a cross-sectional area of 0.47 in.². After load P is applied, the strain in bar (1) is found to be 800 με. Assume L₁-52 in., L₂=90 in., a-36 in., b-34 in., and c-23 in. Determine: (a) the stresses in bars (1) and (2). (b) the vertical deflection vp of point D on the rigid bar. (c) the load P. (2) (1) L₁ B C a Answers: (a) σ₁ = (b) VD = (c) P = i i L2 b C ksi, 0₂ = i in. kips. D P ksi.
Rigid bar ABCD is loaded and supported as shown. Steel [E = 28500 ksi] bars (1) and (2) are unstressed before the load P is applied. Bar (1) has a cross-sectional area of 0.62 in.² and bar (2) has a cross-sectional area of 0.38 in.². After load P is applied, the strain in bar (1) is found to be 670 μe. Assume L₁=68 in., L₂=94 in., a-35 in., b=39 in., and c-22 in. Determine: (a) the stresses in bars (1) and (2). (b) the vertical deflection vp of point D on the rigid bar. (c) the load P. (2) (1) L₁ B C a L2 b C D P
The frame supports the distributed load shown. Determine the state of stress acting at point E. Show the results on a differential element at this point. The section is composed of two materials where E₁ = 200 GPa, and E₂ = 150 GPa AC xxxx E. 4 kN/m -1.5 m 1.5 m--- -3 m 3 m BA 20 mm 60 mm 20 mm 5 m E 50 mm E₁ = 200 GPa E₂ = 150 GPa
The bars of the truss each have a cross-sectional area of 1.92 in². Determine the average normal stress in ksi in member BD due to the loading P = 10 kips. NOTE: use absolute value for Normal stress. The final answer should have 2 decimal places where: L1 =3.8 ft. L2 = 4.3 ft. B L1 D L2 E 0.75 P L2
Rigid bar ABCD is loaded and supported as shown. Steel [E = 28400 ksi] bars (1) and (2) are unstressed before the load P is applied. Bar (1) has a cross-sectional area of 0.75 in.2 and bar (2) has a cross-sectional area of 0.45 in.2. After load P is applied, the strain in bar (1) is found to be 850 μεμε. Assume L1=53 in., L2=79 in., a=34 in., b=33 in., and c=30 in. Determine:(a) the stresses in bars (1) and (2).(b) the vertical deflection vD of point D on the rigid bar.(c) the load P.
Rigid bar ABCD is loaded and supported as shown. Steel [E = 27800 ksi] bars (1) and (2) are unstressed before the load P is applied. Bar (1) has a cross-sectional area of 0.63 in.2 and bar (2) has a cross-sectional area of 0.39 in.2. After load P is applied, the strain in bar (1) is found to be 720 με. Assume L1=56 in., L2=89 in., a=30 in., b=37 in., and c=33 in. Determine: (a) the stresses in bars (1) and (2). (b) the vertical deflection vD of point D on the rigid bar. (c) the load P.
Q3 The truss ABC shown in the figure supports a horizontal load P-900 lb and a vertical load P2= 300 lb. Both bars have cross-sectional area A-2.4 in. and are made of steel with E-20 X 10 psi. (a) Determine the strain energy U, of the truss when the load P, acts alone (P2 -0). (b) Determine the strain energy U2 when the load P2 acts alone (P 0). (c) Determine the strain energy Uz when both loads act simultaneously. 30 B P =900 lb P2 300 lb 40 in.
The bars of the truss each have a cross-sectional area of 1.68 in2. Determine the average normal stress in ksi in member BD due to the loading P = 9 kips. NOTE: use absolute value for Normal stress. The final answer should have 2 decimal places where: L1 =4.0 ft. L2 = 4.1 ft.
Determine the maximum tensile bending stresses in the beam shown. Let P = 15
Determine the maximum tensile bending stresses in the beam shown. LetP= %3D 19 Note Answer in whole number I = 100 × 106 mm4 P kN/m 2. NA 130 mm 6 m B = 4P 200 mm 2P kN 6-X= Am 4P : - GP