A block slides down a ramp from a fixed height and collides with a spring, compressing the spring until the block comes to rest. Compare the amount of compression in the case that the ramp is frictionless to the case where the ramp is not frictionless Explain your answer.

A block slides down a ramp from a fixed height and collides with a spring, compressing the spring until the block comes to rest. Compare the amount of compression in the case that the ramp is frictionless to the case where the ramp is not frictionless Explain your answer.

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter5: Energy

Section: Chapter Questions

Problem 35P: A 0.250-kg block along a horizontal track has a speed of 1.50 m/s immediately before colliding with...

See similar textbooks

Similar questions

A block is attached to a spring, and the block makes contact with a frictionless surface. Sketch a graph of the potential energy of the blockspring system as a function of position along with the corresponding system as in Figure 8.16 (page 224). Use this sketch to show how the block can move to the left from a positive position to a negative position and decrease the elastic potential energy of the system.
Consider the data for a block of mass m = 0.250 kg given in Table P16.59. Friction is negligible. a. What is the mechanical energy of the blockspring system? b. Write expressions for the kinetic and potential energies as functions of time. c. Plot the kinetic energy, potential energy, and mechanical energy as functions of time on the same set of axes. Problems 5965 are grouped. 59. G Table P16.59 gives the position of a block connected to a horizontal spring at several times. Sketch a motion diagram for the block. Table P16.59
A horizontal spring attached to a wall has a force constant of k = 850 N/m. A block of mass m = 1.00 kg is attached to the spring and rests on a frictionless, horizontal surface as in Figure P8.35. (a) The block is pulled to a position xi = 6.00 cm from equilibrium and released. Find the elastic potential energy stored in the spring when the block is 6.00 cm from equilibrium and when the block passes through equilibrium. (b) Find the speed of the block as it passes through the equilibrium point. (c) What is the speed of the block when it is at a position xi/2 = 3.00 cm? (d) Why isnt the answer to part (c) half the answer to part (b)? Figure P8.35
A small ball is tied to a string and hung as shown in Figure P8.34. It is released from rest at position 1, and, during the swing, the string meets a fixed peg as shown. Explain why position 2 at which the ball comes momentarily to rest must be at the same height as position 1.
A 0.250-kg block along a horizontal track has a speed of 1.50 m/s immediately before colliding with a light spring of force constant 4.60 N/m located at the end of the track. (a) What is the springs maximum compression if the track is frictionless? (b) If the track is not frictionless, would the springs maximum compression be greater than, less than, or equal to the value obtained in part (a)?
After ripping the padding off a chair you are refurbishing, you notice that there are six springs beneath, which are intended to contribute equally in supporting your weight when you sit. You find a tag that indicates that the springs are identical and that each has a spring constant of 1.5 103 N/m. What would be the elastic potential energy stored in the six-spring system if you were to sit on the chair?
An inclined plane of angle has a spring of force constant k fastened securely at the bottom so that the spring is parallel to the surface. A block of mass m is placed on the plane at a distance d from the spring. From this position, the block is projected downward toward the spring with speed v as shown in Figure P7.47. By what distance is the spring compressed when the block momentarily comes to rest?
Figure CQ15.5 shows graphs of the potential energy of four different systems versus the position of a particle in each system. Each particle is set into motion with a push at an arbitrarily chosen location. Describe its subsequent motion in each case (a), (b). (c). and (d).
Review. A uniform board of length L is sliding along a smooth, frictionless, horizontal plane as shown in Figure P8.45a. The board then slides across the boundary with a rough horizontal surface. The coefficient of kinetic friction between the board and the second surface is k. (a) Find the acceleration of the board at the moment its front end has traveled a distance x beyond the boundary. (b) The board stops at the moment its back end reaches the boundary as shown in Figure P8.45b. Find the initial speed v of the board. Figure P8.45
A 1.50-kg box rests atop a massless vertical spring with k = 4250 N/m that has been compressed by 15.0 cm from its equilibrium position. The box is released and leaves the spring when it reaches its equilibrium position. What is the maximum height the box reaches above its original position?
An intrepid physics student decides to try bungee jumping. She obtains a cord that is 9.00 m long and has a spring constant of 5.00 102 N/m. When fully suited, she has a mass of 70.0 kg. She looks for a bridge to which she can tie the cord and step off. Determine the minimum height of the bridge that will allow her to stay dry (that is, so that she stops just before hitting the water below). Assume air resistance is negligible.
The spring constant of an automotive suspension spring increases with increasing load due to a spring coil that is widest at the bottom, smoothly tapering to a smaller diameter near the top. The result is a softer ride on normal road surfaces from the wider coils, but the car does not bottom out on bumps because when the lower coils collapse, the stiffer coils near the top absorb the load. For such springs, the force exerted by the spring can be empirically found to be given by F = axb. For a tapered spiral spring that compresses 12.9 cm with a 1 000-N load and 31.5 cm with a 5 000-N load, (a) evaluate the constants a and b in the empirical equation for F and (b) find the work needed to compress the spring 25.0 cm.