A brake mechanism is used to lower body A with a constant velocity of 3.0 m/s. The coefficient of friction between the brake and drum D is 0.40. Neglect the weight of the brake. Determine the mass of body A and the power dissipated by the brake. (hint: the normal force between the brake the and disk is not 1200 N)

Q: Determine the x- and y-coordinates of the mass center of the homogeneous plate of uniform thickness…

A:

Q: Energy (Joule) 70 o $2FRT820 60 S2FRT730 50 A S2FRT650 40 30 20 10 0 -200 S2HT940 S2HT1150 -150…

A:

Q: The level of liquid in a reboiler on a distillation column is controlled by using feedback control…

A: It is asked to draw the cascade arrangement, considering vapour pressure  and actual flow rate as…

Q: Problem 1: Streamlining From dimensional analysis, we know the drag force is FD = CopAV²/2, where CD…

A:

Q: Find the parametric equation of the two lines fla) and giv) from the figure bellow, then detect the…

A: The points (0, 0, 0) and (2, 6, 3) represent the line f(u) as given in the figure. The general form…

Q: The following image describe a single-flash geothermal power plant. We have the follow informations…

A:

Q: 5-30. Determine the force in members EF, CF, and BC, and state if the members are in tension or…

A:

Q: Please answer with a complete solution. Thank you! Find the distance x (measured along AB) at which…

A:

Q: A fluid flows in a 25-cm-diameter pipe at a velocity of 4.5 m/s. If the pressure drop along the pipe…

A:

Q: . Two reservoirs containing water (density of 1.94 slug/ft³ and molecular viscosity of 2.09 x 10-5…

A: The diameter of pipe 1 is d1=1 in.The length of pipe 1 is l1=20 ft.The diameter of pipe 2 is d2=2…

Q: membrane contains surface flaws of initial depth of 0.015 inchesDetermine the life of the membrane…

A:

Q: 4.) Consider a large industrial HVAC duct with a diameter of 1 m that flows air at a pressure of 100…

A:

Q: A) Determine the maximum shear V that the beam can support. B) Determine the maximum allowable…

A:

Q: Determine the vertical displacement of point B and rotation of point C using double integration…

A:

Q: A cylindrical riser with diameter-to-length ratio=1.5 is to be designed for a sand casting mold. The…

A:

Q: A tension-leg platform is connected to a template on the seabed by a series of steel tethers and…

A: The following are the most possible reasons why the electronic sensors had failed.

Q: A steam pipeline of 1200 psia has a crack that is measured approximately as 0.015 inches wide and…

A: Given data

Q: 7-46. Draw the shear and moment diagrams for the beam (a) in terms of the parameters shown; (b) set…

A: To determine:The shear force and bending moment diagram.

Q: Problem 5: Impulse-Momentum no picture necessary Use the Buckingham method to derive the…

A:

Q: NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to…

A: The cycle operates on ideal vapor compression cycle between pressure limit The mass flow rate of…

Q: Determine the reactions on the bent rod which is supported by a smooth surface at B and

A: Find outthe reaction on the bent rod of the smooth surface at B and by the collar A

Q: For each question, provide an explanation, identifying the correct choice ( it is marked in red)…

A:

Q: A two-evaporator compression refrigeration system as shown in the figure uses refrigerant-134a as…

A: The temperature of evaporator 1 is .The temperature of evaporator 2 is The condenser pressure is…

Q: The beam is constructed from two boards fastened together at the top and bottom with three rows of…

A: Here we will calculate the shear force by using the shear formula.

Q: -24 m- 48 KN -2.4 m D 10.7 m 735 KN PROBLEM 6.4 Using the method of joints, determine the force in…

A:

Q: Air is compressed from 140 kPa and 320 K to 1200 kPa in a two stage compressor with intercooling…

A: Here we have simply used the temperature pressure relationship for the isentropic process. And the…

Q: 3 6 The scenario: SAE 30 oil running through a 50 cm new steel sheet metal pipe 50 meters long has…

A: SAE 30 oilDiameter of new steel sheet metal pipe, D = 50 cm = 0.5 mLength of cast iron pipe, L = 50…

Q: The fins on the radiator of your car are about 2 in long. When your car is going 60 mi/h, the…

A:

Q: A steady-flow compressor has R-134a entering at 120 kPa as a saturated vapor and exits at 800 kPa…

A: The initial condition of the refrigerant R-134a.P1=120 kPa (Saturated vapor)The final condition of…

Q: An incoming air flow of 200 m3/h at a temperature of 20°C and a humidity ratio of 0.012 kgv/kga is…

A: The flow rate of air is .The temperature is .The humidity ratio is .The flow rate of mixing air is…

Q: Derive the mobile kinematics, K, of a car-like robot with Ackermann steer- ing as given below, where…

A: Given:

Q: Consider the truss (Figure 1). Suppose that F = 12 kN Figure 6 kN 9 kN G IKOLI H 2 m 1 m B с D 1.5 m…

A:

Q: 3. A 1.5 kW pump delivers 1.2 kg/s water to a building. The water comes in at 100 kPa, and 15°C. The…

A: Given data

Q: 1. four processes. 2. Fill out the blanks by labeling the phase regions. Identify the 3. Indicate an…

A:

Q: A circular tank at a storage facility is 10 metres diameter and contains transformer oil of mass…

A: Diameter of the tank, Density of the oil, Depth of oil in the tank, The diagram is shown below:

Q: A reversible heat pump cycle operates at steady state between hot and cold reservoirs at TH = 30°C…

A:

Q: Un proyectil se dispara de un cañón con una velocidad inicial de 1,000 m/s a un ángulo de 30º con el…

A:

Q: a) Compute the reactions at the supports b) Draw the complete shearing force and bending moment…

A:

Q: Air at 800 kPa and 1200 K enters a converging nozzle with negligible velocity (i.e., these are…

A:

Q: A vessel in the shape of a truncated cone of radii R and r (R > r), has at its base of smaller area…

A:

Q: state flow operation: (a) Pump, (b) Gas turbine, (c) Gas compressor, (d) Nozzle, (e) Throttle valve,…

A:

Q: 11-1 A fixed-end beam AB of length L supports a uniform load of intensity q (see figure). Using the…

A: Here we will use fourth order derivative of deflection curve to get the support reactions.

Q: A simple parallel flow with constant velocity shear σ is given by u = σy  v = w = 0  Evaluate the…

A: To determine:The five components of motion (e.g. translation, divergence, vorticity, shearing, and…

Q: Q1. A ductile hot-rolled steel bar has a minimum yield strength in tension and compression of 350…

A: A ductile hot-rolled steel bar has a minimum yield strength in tension and compression of Syt= 350…

Q: A reducing elbow in a horizontal pipe is used to deflect water flow by an angle = 45° from the flow…

A: Inlet cross-sectional area is A1 = 150 cm2.Outlet cross-sectional area is A2= 25 cm2.The elevation…

Q: A heat exchanger creates energy loss in the fluid system shown below. Water at 50°C flows vertically…

A:

Q: Rod AB is supported by a pin and bracket at A and rests against a frictionless peg at C. AO с 160 mm…

A:

Q: What wind velocity is required to topple an empty tractor trailer, as shown here? The trailer is 48…

A: Given:To find:Wind velocity required to topple the empty tractor trailer.

Q: A) The addition of Ni into steel should reduce the y phase zone. Ture_ — or False

A: Here we will show the gamma phase dependency on the addition of Nickel.

Q: Water is carried through two steel horizontal pipes in series. The upstream pipe is 110 mm of 600 mm…

A: