A Brayton cycle inlet is at 300 K. Inlet and exit temperatures of the turbine is measured as 1800 K and 710 K, respectively. The compressor pressure ratio is 13. Use cold air-standard approach to calculate the thermal efficiency of the cycle. BURNER- COMPR. TURBINE

A Brayton cycle inlet is at 300 K. Inlet and exit temperatures of the turbine is measured as 1800 K and 710 K, respectively. The compressor pressure ratio is 13. Use cold air-standard approach to calculate the thermal efficiency of the cycle. BURNER- COMPR. TURBINE

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Rankine cycle, the pressure and the temperature entering the turbine is 1800 Kpa at 380 Degrees celcius and the pressure leaving the turbine is 20 KPa. The quality of steam entering the condenser is 90%. What is the turbine work in Kj/Kg? A. 833.3 B. 799.9 C. 633.3 D. 423.2
An air-standard Compression Ignition cycle has a compression ratio of 18.2. Air is at 32000R at the end of the heat addition process. Neglecting the variation of specific heats with temperature,determine the following:a. Cut-off ratiob. Net output work of the cyclec. Heat rejection per unit mass, Btu/lbd. Thermal efficiency of the cycle(%). Compare this efficiency value if the cycle has to run on an airstandard Carnot Cycle.
rankine cycle, the pressure and temperature entering the turbine is 1800 kpa and 380 degrees celsius and the pressure leaving the turbine is 20 kpa, the quality of steam entering the condenser is 90%. what is the turbine work in kj/kg at 1.8 mpa and 380 degrees celsius. engine turbine eff=85% mechanical ff=88% determine worknet,work brake, brake heat rate
Given in Table are the pressure and temperature of the steam as it enters the turbine as well as the pressure in the condenser. The given engine operates on a simple ideal Rankine cycle, calculate the unknowns in Table. Show solution Rankine Pressure of Temperature Pressure at the Net work Heat Thermal entering the Efficiency (n) in % the steam entering the entering the condenser system (WN) boiler (Qin) turbine (Rx) turbine (t+) in MPa Engine of the steam done by the in KJ/kg in KJ/kg (Pe) in kPa in °C A 3 350 75
A reheat cycle with two stages of reheating is executed, with steam expanding initially from 202.65 and 540 deg. C. The two reheater pressures are 40 bar and 10 bar, and steam leaves each reheater at 540 deg. C. Condensation occurs at 60 deg. C. Sketch the Ts - diagram. For an ideal cycle, find Qa and e. For the engine operating between the same conditions compute W and e. For a 362, 500 kg/h steam and 100 MW generator output at 94% efficiency, for actual engine, find combined thermal efficiency and combined heat rate and combined engine efficiency and quality of the actual exhaust steam. (3 decimal places in final answer pls)
Steam at 10 MPaa, 550 degrees celsius enters an ideal engine that has one stage of regenerative cycle; condenser pressure is 10kPaa and extraction of steam is at 1 MPa. Compute the following 5. Steam rate
A steam power plant operates between a boiler pressure of 58 bar and a condenser pressure of 0 05 bar Calculate for these limits the cycle efficiency for a Rankine cycle with dry saturated steam at entry to the turbine NB Answer in decimal and not percentage to 4 decimal places
Provide complete solution and detailed diagram. The suction temperature of a diesel cycle is 30oC. The compression ratio is 6 and cut-off ratiois 2. The maximum temperature of the cycle is: A. 1392.22oC B. 1119.22oC C. 967.89oC D. 783.23oC
33 steam 14.0 MPa, 1100°C Generator Turbine 9.5 kPa Boiler H20 (in) H20 (out) Condenser liquid Pump For a Rankine engine operating between these limits, compute the thermal efficiency and the heat rate. b. Considering that a Rankine cycle occurs between the limits, determine QA, QR, WNet, and ec. What mass flow rate is required for a net output of 25 MW? a.
A steam power plant operates between a boiler pressure of 48 bar and a condenser pressure of 0.04 bar Calculate for these limits the cycle efficiency for a Camot cycle using wet steam NB Answer in decimal and not percentage to 4 decimal places.
500 MMSCFD of supercritical steam generated in the steam generator (shown in the sketch below) at P=250 bar and T = 550°C are expanded into a series of two condensing steam turbines (CSTs) to a final pressure of P, = 8 kPa as shown in the diagram below. To improve the efficiency of the cycle, part of the exhaust of the High Pressure (HP) Turbine at P₂ = P = 40bar is reheated to T = 550° C and sent to the Low Pressure (LP) Turbine for further expansion, and part is throttled down to P = 8 bar and mixed with the discharge of the Condensate Pump of the Condenser effluent in the Overflow Feed Water Heater (OFWH) tank in order to preheat the boiler feed water (which also serves as the Deaerator). This power cycle is known as the Regenerative Rankine Cycle with Open Feed Water Heater and it is shown in the diagram below: QH Go 1 STEAM GENERATOR TURBINE DEAERATOR OPEN FEED WATER HEATER FEED WATER PUMP 3 G THROTTUNG LOW PRESSURE TURBINE 8 5 (m) CONDENSATE PUMP Qc CONDENSER If the efficiency of…
Write legibly, provide manual step by step solution, and diagram for below given problem. A supercritical power generates steam at 25 Mpa and 560. The condenser pressure is 7 kpa. Determine the exit quality of steam if it expands through a turbine in this power plant. a. 45.66% c. 56.66%b. 68.45% d. 74.26%