A caliper brake is required for the frontwheels of a sports car with a braking capacity of820N m for each brake. Preliminary designestimates have set the brake geometry as, = 100 mm, r, = 160 mm and 0 = 45°. A padwith a coefficient of friction of 0.35 has beenselected. Deterrmine the required actuating forceand the average and maximum contact pressures.

Answered: Image /qna-images/answer/cb3dc95b-6ed2-4994-ad39-246157f409c4.jpg

A caliper brake is required for the front wheels of a sports car with a braking capacity of 820N m for each brake. Preliminary design estimates have set the brake geometry as 160 mm and 0 = 45°. A pad 1 = 100mm, r, = with a coefficient of friction of 0.35 has been selected. Determine the required actuating force and the average and maximum contact pressures.

A caliper brake is required for the front wheels of a sports car with a braking capacity of 820N m for each brake. Preliminary design estimates have set the brake geometry as 160 mm and 0 = 45°. A pad 1 = 100mm, r, = with a coefficient of friction of 0.35 has been selected. Determine the required actuating force and the average and maximum contact pressures.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A calliper brake is required for the front wheels of a sport's car with a braking capacity of 890,485 Nm for each brake. Preliminary design estimates have set the brake geometry as r=100 mm, ro=155 mm and 0=45°. A pad with a coefficient of friction of 0,45 has been selected. Determine: 4.1. the required actuating forces, 4.2. the average and maximum contact pressures.
The figure shows an internal rim-type brake having an inside rim diameter of 300 mm and a dimension R 5 125 mm. The shoes have a face width of 40 mm and are both actuated by a force of 2.2 kN. The drum rotates clockwise. The mean coefficient of friction is 0.28. a. Find the maximum pressure and indicate the shoe on which it occurs. b. Estimate the braking torque effected by each shoe, and find the total braking torque. c. Estimate the resulting hinge-pin reactions. 30°- 30°. R 120° 120° Pin Pin 30° 30° Figure 3: An internal rim-type brake
Q5: The block brake, as shown, provides a braking torque of 360 N.m The diameter of the brake drum is 300 mm. The coefficient of friction is 0.3. Find 1. the force (P) to be applied at the end of the lever for the clockwise and counter clockwise rotation of the brake drum, and 2. The location of the pivot or fulcrum to make the brake self-locking for the clockwise rotation of the brake dracs 100 10 ( F₁ 4 μ sin 80 20+ sin20 T = (F₁) r Bearing Area A, b(2r sind) RN = (1 20 R 600 Brake drum
The torque transmitted by a single block brake is 70 N-m. The coefficient of friction between the drum and the lining is 0.35. The drum diameter is 240 mm. Which of the following is the normal force RN pressing the block on the brake block on the wheel? 200 200 4 TEL 200 N 560 N 1600 N 1450 N
A caliper brake is required for the front wheel of a van with a braking capacity of 900 Nm, for each brake. Preliminary design estimates have set the brake geometry as Ri =100 mm, Ro =160 mm and angle of 45 degrees. A pad with a coefficient of friction of 0,3 has been selected. Determine 2.1 the required actuating forces 2.2 the average and maximum contact pressures
A car engine has its rated output of 120 kW. The maxdmum torque developed is 110 Nm, The clutch used is of single plate type having two active surfaces. Axia! pressure is not to exceed 0.85 bar. External diamater of friction plate is 1.25 times the internal diameter. Determine the dimensions of friction plate and axial force exerted by the spring. Assume uniform wear and coefficient of friction to be 0.3.
The hand brake of Fig. is used to control the rotation of a drum. The coefficient of friction between the belt and the drum is , = 0.15, and the weight of the handle may be neglected. If a counterclockwise torque of 5 ft - Ib is applied to the drum Repeat the problem for a clockwise torque of 5 ft · Ib. What happens to the system at a 4.6 in.? What does the solution mean for a> 4.6 in.? M= 5 lb-ft -12 in. 12 in
A band brake embraces a 500 mm diameter drum with an angle of lap of 270° and produces a braking torque of 200 Nm. The coefficient of friction is 0.2. One end of the band is attached to the fulcrum pin and the other end is attached to a pin B. Which of the following is the tension in the slack side of the band? 75 -450 C 270° O 280 N O 510N O 255 N 0 445 N All dimensions in mm.
A block brake with a torque of 250 N-m. Its drum rotates at 100 rpm. The length of the block (1) is twice its width (w). Assume, the coefficient of friction P is 0.35. Calculate: (1) the applied load (P) and the hinge-pin reaction (Rx ana Ry) for clockwise rotation of the drum; (2) the applied load and hinge-pin reaction for anticlockwise rotation of the drum; (3) the rate of heat generated during the braking action. (4) The dimensions of the block, if the intensity of pressure between the block and brake drum is 1 MPa. (5) Check whether the brake is self-locking.
SELF-CHECK EXERCISE PROBLEM 06. What force F must be exerted on the brake arm shown to hold the drum against rotation if P = 1000KN and the coefficient of belt friction is 0.30. Figure, F ¡A 800mm 450 B 200mm 100mm 200mm CI P=1000KN
The band of a brake has a contact angle of 18° deg. If the pulls on the bands are 275 kg and 100 kg, find the coefficient of friction.
Determine the principal dimensions of a cone clutch faced with lather to transmit 40 kW at 800 r.p.m. from an electric motor to an air compressor. Sketch a sectional front view of the clutch and provide the main dimensions. Assume that the semi-angle of the cone is 10°, the coefficient of friction is 0.3, mean diameter of cone is (7-10)d, where d is the diameter of the shaft, allowable normal pressure for lather and cast iron is 0.1 to 0.2 N/mm, shear stress 100 N/mm², load factor is 2 and the mean diameter to face width ratio is 6.