A cast iron pipe (roughness =0.26 mm or 0.010 inches) having a diameter of 100 mm is used to fill the empty cylindrical tank with water at 40 degree C. If the power output of the pump is 4.5 kW, determine the depth of h in water in the tank 6 minutes after the pump is turned on. The pipe has a total length of 50 m. Neglect minor losses

Q: Plan out design verification for Powered wheelchair medical device 2 and validation -> including…

A: Given Powered wheelchair To find Design plan Manufacturing quality verification

Q: A cylinder vessel filled with water with a 2m diameter and 5m high. It was rotated with uniform…

A:

Q: Q5: A vary large furnace contains hot gas and particles at (1700 C) heat is transferred from gases…

A:

Q: A golf ball is struck with a velocity of 80 ft/s as shown. Determine the distance d to where it will…

A: Given DataV=80ft/sθ=45°

Q: 7.261 kg of steam at a pressure of 20 bar and temperature of 300 deg C expands isentropically to a…

A:

Q: Determine the axial force (kN) in each member of the assembly shown below. Member Cross-Sectional…

A: Trusses are constructions made solely of components with two forces. Each truss member is believed…

Q: *17-3 Design a single-surface disk clutch to transmit 100 N-m of torque at 750 rpm using a molded…

A: Given data:

Q: A car takes 10 sec, to cover a distance of 30 m , and takes 12 sec. to cover 42 m, find the…

A:

Q: The torque of 100 kip - ft is applied in the 16-ft-long hollow steel shaft. Note that the inner…

A:

Q: Given the image below, determine the ideal force diagram for the structure given the choices

A: According to the details provided in the question, we need to find the correct F.B.D. of the given…

Q: The rigid beam is supported by the three posts A, B, and C. Posts A and C have a diameter of 60 mm…

A:

Q: APprove that Epn 1. To T-To -Si)-Cho-hi) up by intgrating Epn with l sh = 59 ds %3D %3D will bg…

A:

Q: Q6/ The value of compound stress of normal stress is equal to summation of both stresses due to…

A: The members may be subject to eccentric load or combination of bending moment and axial force. Then…

Q: y 400 тm В to 250 тm 20° A А

A:

Q: Draw the shear and moment diagram of the loaded beam shown below and determine the maximum moment…

A:

Q: At a point upstream of the throat in a conv.-div. nozzle, the velocity, pressure and temperature 242…

A:

Q: A newly purchased container that has a capacity of 1 m³ contains a mixture of liquid and steam in…

A:

Q: A fluid having a specific gravity of 0.869 and dynamic viscosity of 0.0814 Pa-s flows through a cast…

A: Given:

Q: 2Pk/ft Pk/ft А В L L/2

A:

Q: 3. For a single cylinder petrol engine works on the diesel cycle, the pressure at the beginning and…

A:

Q: A link in a mechanism is to be subjected to a tensile force that varies from 3500 to 500 N in a…

A: Soln :- In a given problem we have a link that mechanism is subjected tesnile force which is able to…

Q: Equation of Equilibrium. Referring to the free-body diagram of the beam shown in Fig. a, +1£F, = 0;…

A:

Q: Problem 8.14 A curved bar of circular cross-section 100 mm in diameter has a radius of curvature of…

A:

Q: 22. Write the Miller Indices for the following planes. ja2 ja2 a3

A: solution to first question 22 as per our company policy: To find: Miller indices of the given…

Q: Vibration Engineering Mechanical Engineering

A: Given that, Mass of the passengers, m=124 kg/m,Length of the chair, L=5 m,Dimension of the spring,…

Q: ANSWER ASAP Using the velocity distribution for a laminar, incompressible flow of a…

A:

Q: Introduction on Automobile sensors.

A: An automobile is a human-controlled vehicle that is not powered by humans. Car sensors and their…

Q: Fluid of specific gravity 0.80 flows in a 230 mm diameter pipe. Find the critical velocity in m/s.…

A: Given information, S=0.8, D=0.23m Viscosity Find, Critical velocity

Q: 7 shows a mechanism in which the crank OA, 100 mm long rotates clo he connecting rod A B is 400 mm…

A:

Q: A solid 11 mm diameter shaft is subjected to an axial load of P= 33 kN and a torque of T acting as…

A: Sum of moment of intera of two perpendicular axes is known as polar moment of inertia.

Q: A force F = 185 N is applied to a two-bar truss as shown and 0 = 36 degree. Determine the value of…

A: FBD of the question can be drawn as shown below:   From the data given in question, F = 185 N θ =…

Q: TRUE OR FALSE:  ​​Any equation that comes out of the differential approach is valid at every point…

A: (1) The first statement is False, since differential approach provides different value for different…

Q: 7.450 kg of steam at a pressure of 20 bar and temperature of 300 deg C expands isentropically to a…

A:

Q: 7. Steam turbine receives steam at 7MPa and 550 deg C and exhausts as 20kPa. Determine the turbine…

A:

Q: 150 mm 150 mm C B 400 mm 600 mm

A:

Q: A thin-walled steel pipe transports water at a pressure of 80 lbf/in?. There is negligible restraint…

A:

Q: In the figure below, a circular disk wih a radius R= 15 cm rolls (without slipping) to the left with…

A:

Q: The members of the truss shown below have a cross-sectional area of 10,000 mm2. Determine the…

A:

Q: Based on the given structure, calculate: i) The resultant force. The direction (angle) of the…

A:

Q: Water vapor at 100 kPa and 150°C is compressed isothermally until half the vapor has condensed. How…

A:

Q: A system consisting of 2 kg of water initially at 100°C, 10 bar undergoes an internally reversible,…

A:

Q: A piston-cylinder assembly contains a two-phase liquid-vapor mixture of water with an initial…

A: Answer: The work is 1511.500 kW.

Q: A Pelton wheel develops (8 MW) under a net head of (130 m) at a speed of (200 rpm). Assuming the…

A: Given, Power of pelton wheel = P = 8 MW = 8 x 106 W Available head = H = 130 m Speed of pelton wheel…

Q: Q3/ Both the loads (10 KN + 2 KN) applied on the beam results a compound stresses called NORMAL…

A: Total normal stress due to load 10 kN and load 2 kN.

Q: The oil tanks in Tinyland are only 160 cm high, and they discharge to the Tinyland oil truck through…

A:

Q: Find the pressure difference between points A and B. (1,3,5,7,9): Liquid is Chloride with density…

A:

Q: A cantilever beam, 80 mm wide by 290 mm high and 9 m long, carries a load that varies uniformly from…

A:

Q: 3. For a single cylinder petrol engine works on the diesel cycle, the pressure at the beginning and…

A:

Q: 8- Determine the reactions at the supports. 900 N/m 600 N/m A 3 m 3 m- B.

A:

Q: Question 9 23.102 kg per second of water at 0.03398675 kbarg and internal energy of 15000 kW is…

A:

Metrology of surface finish

In general terms, the application of scientific principles in the study of measurements is known as metrology. When speaking about measurement, it could be of time, length, microstructures, grain structures, internal crystal discontinuities, surface roughness, measurements of angles, height, width, and so on. While coming to the domain of mechanical engineering, metrology is considered the science of measurements of surface finish, length, surface texture, and angles.