A chain with a 0.75 in pitch is designed to run on sprockets having 15 and 50 teeth, respectively. If the center distance of the sprockets is specified to be 36 in, what is the length of chain required in pitches? (Round to the nearest even number of pitches). 130 pitches 132 pitches 136 pitches 138 pitches 140 pitches (A) (B) (C) (D) (E)

A chain with a 0.75 in pitch is designed to run on sprockets having 15 and 50 teeth, respectively. If the center distance of the sprockets is specified to be 36 in, what is the length of chain required in pitches? (Round to the nearest even number of pitches). 130 pitches 132 pitches 136 pitches 138 pitches 140 pitches (A) (B) (C) (D) (E)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A chain and sprocket has a pitch diameter of 30 inches and with 90 teeth available. Find the pitch of the chain in inches.
Find the displacement of point "P" (in mm) using quadratic shape functions, when the displacements of nodes 1, 2 and 3 are q1=0.10 mm, q2=-0.10 mm and q3=0.14 mm, respectively. Suppose that the values of shape functions are N1=-0.08, N2=0.36 and N3=0.72. (Hint: round your answer to 4 digits after decimal point) 1 x1 2 x2 * P 3 X3
A helical gear of 10 inches pitch diameter has a helix angle of 25 degree, and there are 35 teeth. The gear transmits 40 hp and rotates at 450 rpm with a normal pressure angle of 20 degrees. What is the value of the normal circular and diametral pitch in inches? (A) 0.898 and 3.5 B 0.889 and 3.5 0.889 and 3.3 D 0.898 and 3.2
Number of teeth of gears z1: 22 Tooth numbers of gears z2: 90 Tooth numbers of gears z3: 23 Tooth numbers of gears z4: 77 The efficiency of gear pairs ηd: 0,96 The efficiency of the bearing pairs ηr: 0,94 Electric motor speed: 2050 Belt speed (v) (m / s): 1.30 Required force for belt movement (N) g: 2200 a) Find the diameter of the drum? b) Find the required motor power?
A chain with speed of 900 fpm has driving sprocket turns at 1000 rpm. If the pitch of chain is 3/4-in, find the number of teeth of driving sprocket. (Ans. 14 teeth)
The plot below of load vs. extension was obtained using a specimen (shown in the following figure) of an alloy remarkably similar to the aluminum-killed steel found in automotive fenders, hoods, etc. The crosshead speed, v, was 3.3x104 inch/second. The extension was measured using a 2" extensometer as shown (G). Eight points on the plastic part of the curve have been digitized for you. Use these points to help answer the following questions. 1. 900 800 (0.10, 630 ) 700 (0.50, 745) (0.30, 729) 600 (0.20, 699) (0.40, 741.5) 500- (0.004, 458) (0.80, 440 ) - 400 (0.0018, 405) 300 D= 3.3 " 0.03" 200 G=2.0" 100 - 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 Extension, inches a. Determine the following quamtities. Do not neglect to include proper units in your answer. Young's Modulus Total elongation Yield stress Ultimate tensile strength Uniform elongation Engineering strain rate Post-uniform elongation b. Construct a table with the following headings, left-to-right: Extension, load, engineering strain,…
A helical gear of 10 inches pitch diameter has a helix angle of 25 degree, and there are 35 teeth. The gear transmits 40 hp and rotates at 450 rpm with a normal pressure angle of 20 degrees. Find the axial force transmitted by the gear. A 252.26 lb B 225.26 lb C 522.26 lb D) 552.26 lb
A winch drum has an effective diameter 0.25m and is turning at 22 rpm. What is the resulting line speed in m/min? Give your answer to 1 decimal place without units eg if you think it is 102.341m/min, simply type 102.3.
3. The reduction of speed from 360 r.p.m. to 120 r.p.m. is desired by the use of chain drive. The driving sprocket has 10 teeth. Find the number of teeth on the driven sprocket. If the pitch radius of the driven sprocket is 250 mm and the center-to-center distance between the two sprocket is 400 mm, find the pitch and length of the chain. [Ans. 30 ; 52.25 mm ; 1.93 m]
A 21-tooth sprocket is connected to a 63-tooth sprocket by means of RC 60 having 180 pitches. Determine the distance between the sprockets in inches.
Ex. #1] Given a gear of 16 teeth, 4 diametral pitch. The dedendum equals 1/P, inch, the clearance is to be one-eight of the addendum, and the backlash is to be 2 percent of the circular pitch. Calculate the following, giving the results to 3 decimal places: a) the pitch diameter; b) the addendum and dedendum diameter; c) the whole depth; d) the backlash; e) the tooth thickness; and f) the space width. Given: A spur gear T = 16 teeth Backlash = 0.02 P Add = 1/Pd Clearance = (1/8) addendum Required: Determine the a) D, b) Add and Ded diameters, c) whole depth, d) backlash, e) tooth thickness, f) space width. Solution: (To be discussed during the lecture period)
A helical gear of 10 inches pitch diameter has a helix angle of 25 degree, and there are 35 teeth. The gear transmits 40 hp and rotates at 450 rpm with a normal pressure angle of 20 degrees. What is the value of the diametral pitch in teeth per mm?