Answered: A circular cylinders of radius r and…

A circular cylinders of radius r and mass m is connected by two springs, as shown below. Derive the equation(s) of motion using Lagrange's equations.(1 = -mr²) 0(t) k in a

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A solid disc with radius R is connected to spring at point (d) distance above the center of disc. The other end of the spring is fixed to the vertical wall. The disc is free to roll without slipping on the ground. The mass of disc is (M) and the spring constant is (K). The polar moment of inertia for disc about its center is J = 1/2MR2 , so the natural frequancy for the system is 1 2K(R+d)² MR2 the Answer is O 1 2K 2п 3M
Two uniform bars AB and BC are pin-connected at points A, B, and C. Bar AB is massless (mAB = 0 kg) and has a length L = 1.5 m. Bar BC has a mass mBc = 2 kg and a length H = 1 m. C is a fixed point, a distance 8 = 0.2 m above the ground. A is on a uniform wheel of radius R = 0.8 m, a distance p from the center of the wheel. Note that p is less than R (R+ p = 8 + H). The mass of the wheel is mwheel = 6 kg. At the instant shown, AB is horizontal, BC is vertical and point A is at the vertical of point O. Bar BC is rotating clockwise at 3 rad/s with an acceleration of 1.5 rad/s² also in the clockwise direction. Assume that the wheel rolls without slipping. a) Find the force P applied to the wheel at that instant. b) Find the minimum coefficient of static friction required for the wheel to roll without slipping. L B H
Problem 1: A uniform thin rod of mass m = 4.4 kg and length L = 1.2 m can rotate about an axle through its center. Four forces are acting on it as shown in the figure. Their magnitudes are F1 = 4.5 N, F2 = 4.5 N, F3 = 12.5 N and F = 19.5 N. F, acts a distance d= 0.28 m from the center F, 45° of mass 60° F. 3 Part (a) Calculate the magnitude t, of the torque due to force F1, in newton meters. 1 = 2.7 / Correct! Part (b) Calculate the magnitude tz of the torque due to force F2 in newton meters. 12= 0.89 / Correct! Part (c) Calculate the magnitude t3 of the torque due to force F3 in newton meters. / Correct! 13 =0 Part (d) Calculate the magnitude t4 of the torque due to force F, in newton meters. 1=0 v Correct! Part (e) Calculate the angular acceleration a of the thin rod about its center of mass in radians per square second. Let the counter-clockwise direction be positive. a = sin() cos() tan() 8 9 HOME cotan() asin() acos() E AL 4 6 atan() acotan() sinh() 1 2 3 cosh() tanh() cotanh()…
Three masses are attached to a uniform meter stick, as shown in figure. The mass of the meter stick is 150.0 g and the masses to the left of the fulcrum are m1 = 50 kg, m2 = 75 kg, and m3 that balances the system when it is attached at the right end of the sticky, and the normal reaction force at the fulcrum when the system is balanced. Also, find the mass m3.
1. Determine the number of degrees of freedom necessary for the analysis of the system shown in the figure below. Identical slender rods of length L and mass m 4.
A homogeneous slender bar AB of mass m and length L is released from rest in the position shown in figure below. Assuming that the horizontal plane is frictionless. 1.) Draw the free body diagram and say how many forces act on the bar and which force is doing the work. 2.)Draw the kinematic diagram and show how manoy vectors act on the bar. 3.) Draw the kinetic diagram and show how many inertia-term vectors act on the bar.
A homogeneous beam AB weighs P, where a point is a rope wound around a homogeneous cylinder. The cylinder has radius R, mass m, and center of mass C is moving down the plumb line. Find 1) the acceleration of the circular wheel; 2) tension of rope; 3) Reaction force of bearing A and B H 112 12
Consider the system shown in the figure. Disk m, rolls without slip. a is defined as the displacement of mass mo and is positive to the left. When x displaces in a positive direction, it rotates the disk (with moment of inertia J1 and radius R) by an angle 01. Use 0, to denote the rotation of the mass m, (a disk with moment of inertia J, and radius r2). Assume small displacements (and hence small rotations). Use x as the coordinate to describe this system. mo m2 ww k Syntax Use J[1],J[2], k[1].r[1].r[2],m[2] for J1 ,J9,k1.r1.r2 and m2. Use m[0] (m with subscript as the number zero) for mo- How many degrees of freedom does this system have? The system has 2 degrees of freedom - from the disk and cart that are on the horizontal surface plus the rotating disk on the left. The system has 4 degrees of freedom: translation and roation of the first disk, rotation of the other disk and translation of mass mo- O None of the other responses are correct. O The system has 3 degrees of freedom…
A car is modeled as shown in Figure. Derive the equations of motion and find matrix M, C, and K. Mass = M, mass moment of inertia = JG .000 m1 k₂ F1 1 k2 000 k₁ k₁ m2 F2, X2 ell
SECW OM A motorbike wheel with an 8 kg mass has a 0.4 m radius of gyration around the z-axis, as shown in Figure. The wheel's shaft is supported by bearings A and B and rotates at a constant rate of 150 rpm in a counter-clockwise direction from the z-axis, while the frame rotates at 12 rpm in a counter- clockwise direction from the y-axis. Determine the resultant reaction forces at each bearing A and B due to the mass and gyroscopic effects. With the result of forces, which bearing has a tendency to fail first, which bearing should be considered for design purposes and explain the effect on motor if the bearing fail. y 0.55 0.4 All dimensions in meter (m)
The rope shown in the figure below is wound around a cylinder of mass 4.0 kg and I = 0.020 kg m2, about the cylinder axis. If the cylinder rolls without slipping, what is the linear acceleration of its center of mass? What is the frictional force? Use an axis along the cylinder axis for your computation. What happens if the frictional force between table and cylinder is negligible? Choose any axis for your computation.
a The pendulum shown in the figure consists of a uniform thin plate of mass 750 grams with dimensions a = 20 cm by b = 3 cm rigidly connected to a uniform disk of mass 800 grams and radius r from a fixed pin at point P; there is no friction in the pin. (There is nothing tricky about the geometry pin.) 5 cm. The pendulum swings the center of the disk is a + r = 25 cm from the If the pendulum is released from rest at 0 angular velocity of the pendulum at 0 O radians (horizontal), what is the * radians (vertical)?