Homework Help is Here – Start Your Trial Now!
Math
Advanced Math
A composition sensor is used to continually monitor the contaminant level in a liquid stream. The dynamic behavior of the sensor can be described by a first-order transfer function with a time constant of r in seconds. Consider C and Cm the actual contaminant concentration and the measured value by the biosensor, respectively. The initial (before the change) concentration of contaminant and therefore the sensor reading is CA0 ppm (i.c., the values at t-0). An alarm sounds if the measured value exceeds the environmental limit of 7 ppm. Suppose that the actual contaminant concentration in the liquid stream (i.e. C) gradually increases according to the expression, C(t)= a + bt, where t is expressed in seconds; a and b are constant positive numbers (this is called ramp input which is different from step change). Select all correct statements: The transfer function, G(s) is Cm(s) C(s) Based on the transfer function, the steady-state gain (K₂) of the sensor is 1. steady-state gain (K₂) of a process is defined as 1 TS + 1 where Y and U denote the corresponding steady state values of the output (response) and input (change) variables. C(s)= a + bs In the previous question, in order to find the sensor reading, Cm(s), in the transfer function (G(s)), you need to know the change of actual concentration in the Laplace domain. Which of the following represents the C(s) in the transfer function (Hint: Should C(s) be in a deviation format and in a Laplace domain)? C(s)= a/s + bs Y₂-Y₁ U₂-U₁ C(s)= a/s + b/s² C(s)=b/s² In the previous question, What is the analytical solution of the sensor response with respect to time if: 1. the input, C(t)=5+0.2t 2. sensor time constant is 10 seconds 3. the steady state concentration before change is 5ppm

A composition sensor is used to continually monitor the contaminant level in a liquid stream. The dynamic behavior of the sensor can be described by a first-order transfer function with a time constant of r in seconds. Consider C and Cm the actual contaminant concentration and the measured value by the biosensor, respectively. The initial (before the change) concentration of contaminant and therefore the sensor reading is CA0 ppm (i.c., the values at t-0). An alarm sounds if the measured value exceeds the environmental limit of 7 ppm. Suppose that the actual contaminant concentration in the liquid stream (i.e. C) gradually increases according to the expression, C(t)= a + bt, where t is expressed in seconds; a and b are constant positive numbers (this is called ramp input which is different from step change). Select all correct statements: The transfer function, G(s) is Cm(s) C(s) Based on the transfer function, the steady-state gain (K₂) of the sensor is 1. steady-state gain (K₂) of a process is defined as 1 TS + 1 where Y and U denote the corresponding steady state values of the output (response) and input (change) variables. C(s)= a + bs In the previous question, in order to find the sensor reading, Cm(s), in the transfer function (G(s)), you need to know the change of actual concentration in the Laplace domain. Which of the following represents the C(s) in the transfer function (Hint: Should C(s) be in a deviation format and in a Laplace domain)? C(s)= a/s + bs Y₂-Y₁ U₂-U₁ C(s)= a/s + b/s² C(s)=b/s² In the previous question, What is the analytical solution of the sensor response with respect to time if: 1. the input, C(t)=5+0.2t 2. sensor time constant is 10 seconds 3. the steady state concentration before change is 5ppm

Algebra & Trigonometry with Analytic Geometry
Algebra & Trigonometry with Analytic Geometry
13th Edition
ISBN:9781133382119
Author:Swokowski
Publisher:Swokowski
Chapter7: Analytic Trigonometry
Section7.6: The Inverse Trigonometric Functions
Problem 94E
See similar textbooks
icon
Related questions
Question

Please do all and work on it because they need each other

A composition sensor is used to continually monitor the contaminant level in a liquid stream. The dynamic behavior of the sensor can be described by a first-order transfer function with a time constant of t in seconds. Consider C and Cm the actual contaminant concentration and the measured value by the biosensor, respectively. The initial (before the change) concentration of contaminant and therefore the sensor reading is CAO ppm (i.c., the values at t = 0). An alarm sounds if the measured value exceeds the environmental limit of 7 ppm. Suppose that the actual contaminant concentration in the liquid stream (i.e. C) gradually increases according to the expression, C(t)= a + bt, where t is expressed in seconds; a and b are constant positive numbers (this is called ramp input which is different from step change). Select all correct statements: The transfer function, G(s) is Cm(s) C(s) G(s) Based on the transfer function, the steady-state gain (Kp) of the sensor is 1. steady-state gain (K₂) of a process is defined as Kp = 1 TS + 1 where Y and U denote the corresponding steady state values of the output (response) and input (change) variables. C(s) = a + bs In the previous question, in order to find the sensor reading, C,(s), in the transfer function (G(s)), you need to know the change of actual concentration in the Laplace domain. Which of the following represents the C(s) in the transfer function (Hint: Should C(s) be in a deviation format and in a Laplace domain)? C(s)= a/s + bs C(s)= a/s + b/s² C(s)=b/s² Y₂-Y₁ U₂-U₁ In the previous question, What is the analytical solution of the sensor response with respect to time if: 1. the input, C(t)=5+0.2t 2. sensor time constant is 10 seconds 3. the steady state concentration before change is 5ppm
Transcribed Image Text:A composition sensor is used to continually monitor the contaminant level in a liquid stream. The dynamic behavior of the sensor can be described by a first-order transfer function with a time constant of t in seconds. Consider C and Cm the actual contaminant concentration and the measured value by the biosensor, respectively. The initial (before the change) concentration of contaminant and therefore the sensor reading is CAO ppm (i.c., the values at t = 0). An alarm sounds if the measured value exceeds the environmental limit of 7 ppm. Suppose that the actual contaminant concentration in the liquid stream (i.e. C) gradually increases according to the expression, C(t)= a + bt, where t is expressed in seconds; a and b are constant positive numbers (this is called ramp input which is different from step change). Select all correct statements: The transfer function, G(s) is Cm(s) C(s) G(s) Based on the transfer function, the steady-state gain (Kp) of the sensor is 1. steady-state gain (K₂) of a process is defined as Kp = 1 TS + 1 where Y and U denote the corresponding steady state values of the output (response) and input (change) variables. C(s) = a + bs In the previous question, in order to find the sensor reading, C,(s), in the transfer function (G(s)), you need to know the change of actual concentration in the Laplace domain. Which of the following represents the C(s) in the transfer function (Hint: Should C(s) be in a deviation format and in a Laplace domain)? C(s)= a/s + bs C(s)= a/s + b/s² C(s)=b/s² Y₂-Y₁ U₂-U₁ In the previous question, What is the analytical solution of the sensor response with respect to time if: 1. the input, C(t)=5+0.2t 2. sensor time constant is 10 seconds 3. the steady state concentration before change is 5ppm
Expert Solution
trending now

Trending now

This is a popular solution!

steps

Step by step

Solved in 3 steps with 3 images

SEE SOLUTIONCheck out a sample Q&A here
Blurred answer
Recommended textbooks for you
Algebra & Trigonometry with Analytic Geometry
Algebra & Trigonometry with Analytic Geometry
Algebra
ISBN:
9781133382119
Author:
Swokowski
Publisher:
Cengage
Calculus For The Life Sciences
Calculus For The Life Sciences
Calculus
ISBN:
9780321964038
Author:
GREENWELL, Raymond N., RITCHEY, Nathan P., Lial, Margaret L.
Publisher:
Pearson Addison Wesley,
College Algebra
College Algebra
Algebra
ISBN:
9781938168383
Author:
Jay Abramson
Publisher:
OpenStax
SEE MORE TEXTBOOKS