I need the answer as soon as possible A compression spring has squared ends and is made of Music wire A228. The mean coildiameter is 20 mm, and the wire diameter, d = 2.24 mm. The spring has a free length of262 mm, and 29 total coils.(a) Calculate the pitch of the spring at the free length.(b) Calculate the solid height for the spring.(c) Calculate the deflection to compress the spring to its solid height.(d) Calculate the spring constant for the spring.(f) Determine the force to compress the spring to its solid height.(g) Determine whether the spring will buckle before it reaches its solid height if thespring is unrestrained.

We are suppose to solve only 3 sub parts. Please post other parts as a separate question.

Answered: A compression spring has squared ends…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A helical compression spring is wound using 0.12-in-diameter phosphor-bronze B159 wire. The spring index C = 10 and the total number of coils is N = 14. You may assume that the spring has both ends squared and ground and is supported between fixed ends. Also, Sgy = 0.45 · Sut- a. Estimate the spring rate. b. Estimate the static load corresponding to the yield strength. c. What should the free length of the spring be to ensure that when it is compressed solid the torsional stress does not exceed the yield strength? d. Calculate the critical value of the free length of the spring to avoid buckling.
A helical compression spring is used to absorb heavy vibrations. Apply mechanical engineering design theory and by using the values given in the table below, (i) Calculate the force applied on the spring. (ii) Determine the number of turns. (iii) Determine the spring stiffness. (iv) Calculate the free length. 5 maiks (v) Would you recommend to increase the number of turns and free length of the spring for this application ? Why? (answer in one/two sentences only). Spring data Туре Helical squared and ground ends Initial Compression of spring 30 mm 80 mm Further Compression of spring after applying heavy load Shear Stress Modulus of rigidity 750 N/mm2 82000 MPa Wire diameter 8 mm Spring Index
A helical compression spring is made with oil-tempered wire of diameter 0.2", mean coil diameter of 2", 12 total coils, 5" free length, and squared ends. (a) Find the solid length. (b) Find the force required to compress the spring to closure? (c) Find the factor of safety against yield when compressed to the solid length. (Hint: Uses Say= 0.5 Sut for shear strength.)
1. Design a compression helical spring to carry a load of 500 N with a deflection of 25 mm. The spring index may be taken as 8. Assume the following values for the spring material: Permissible shear stress = 350 MPa Modulus of rigidity = 84 kN/mm2 4С - 1 0.615 Wahl's factor where C-spring index. 4С - 4
Design a compression helical spring to carry a load of 500 N with a deflection of 25 mm. The spring index may be taken as 8. Assume the following values for the spring material: Permissible shear stress 350 MPa Modulus of rigidity = 84 kN/mm? 4С -1 0.615 Wahl's factor 4C – 4 where C= spring index. C [Ans. d= 5.893 mm; D= 47.144 mm;n=6| %3D
A spring is designed to fire a 2 kg projectile. The outside diameter of the coil is 160 mm with an 18mm wire and a total of 22 coils squared and ground. The spring has a free length of 650 mm. When set or loaded, the spring is compressed to a length of 450 mm. a. Determine the spring index, as well as the active number of coils b. Find the spring deflection and Wahl's factor.
1. Design a compression helical spring to cary a load of 500 N with a deflection of 25 mm. The spring index may be taken as 8. Assume the following values for the spring material: Permissible shear stress 350 MPa Modulus of rigidity = 84 kN/mm2 4C – 1 + 4C – 4 0.615 Wahl's factor -, where C= spring index. [Ans. d= 5.893 mm; D=47.144 mm; n 6]
- In a compound helical spring, the inner spring is arranged within and concentric outer one but is 10 min shorter. The outer spring has 10 coils of mean diaineter 30 min and wire dia 3 mm. Find stiffness of inner spring if an axial load of 100 N causes outer one to compress by 20 mm. If the radial clearance between the springs is 2 mm, find wire diameter of inner spring which has 8 coild. G 80 kN/mm.
A square end compression helical spring has an operation load range of 3.5KN to 4.2KN.The deflection for the load range is 8mm and the spring index is 6.if the permissible shear stress and module of rigidity for the material of the spring are 380MPa and 90pa respectively, including the effect of the wire curvature. Design the spring by, determine (A)wire diameter (B) mean coil diameter (C) number of active turns (D)total number of turns
A spring with squared and ground ends is used for a load and deflection of 1.2 kN and 20 mm, respectively, with a spring index of 4. The wire diameter is 6 mm and the modulus of rigidity is 84 GPa. Which of the following is the active number of turns of the spring?
A spring made from music wire ASTM 228 steel has the following data: Free length=1.75" Wire diameter=0.055" Outside diameter=0.561" Applied load= 14 lb Ends=square and ground both ends hinged Number of coils=10 G=11.85 x 106psi E= 30 Mpsi Find Mean diameter, spring index, deflection, spring rate, force at solid length, check for buckling,coil clearance and hole diameter
2. A helical valve spring is to be designed for an operating load range of approximately 90 to 135 N. The deflection of the spring for the load range is 7.5 mm. Assume a spring index of 10. Permissible shear stress for the material of the spring = 480 MPa and its modulus of rigidity 80 kN/mm2. Design the spring. 4С - 1 0.615 , C being the spring index. Take Wahl's factor %3D 4С - 4 [Ans. d = 2.74 mm ; D = 27.4 mm ; n = 6]

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS