Marked out of 10.00P Flag questionA beam (AB) is attached to a roller at B and a pin atA. It is subjected to a concentrated force of 2500 Nand a couple moment of 900 N.m. as shown in thefigure below. The reaction force at the roller B is.2500 N900 N mB1.5 m1.5 m1.5 mSelect one:O a. 1200 N upwardO b. 1300 N upwardO c. 1300 N downwardO d. 1200 N downward

reaction force at b is required

Answered: a concentrated for nt of 900 N.m. as n…

Engineering

Mechanical Engineering

a concentrated for nt of 900 N.m. as n ction forco at th

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A truss is facing a two-force member and both of them are in the opposite directions, and the truss is in equilibrium. And both of them are coming to each other. The forces are called Select one: O a. Tensile Forces O b. Compressive forces O c Parallel and collinear forces with same direction of heading O d. The rotational forces Next page est-3 Jump to...
Q5/A) From the figure below, determine the reaction force at pin C. A 000 0.6 m 10 kN 0.6 m 0.8 m 60° 0.4 m 6 kN OB
The homogeneous AB beam weighs 400 lbs. For each support condition in (a) a (d), plot the DCL of the beam and determine the number of unknowns.
The vertical reaction at A is closest to: A. 200 kN B. 300 kN C. 204 kN D. 180 kN Answer: (write the answer in capital letter, no period or spaces) The vertical reaction at B is closest to: A. 200 kN B. 300 kN C. 204 kN D. 180 kN Answer: (write the answer in capital letter, no period or spaces)
Use the graphical method to construct the shear-force and bending-moment diagrams for the beam shown. Let a-3.0m, b-6.0 m, M₁-55 kN-m and Mc-85 kN-m. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise. My Answers: A, A Calculate the reaction forces A, and D, acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since A, 0, it has been omitted from the free-body diagram.) 178.46 Mc eTextbook and Media Me KN, D,- 41.45 KN.
A truss is facing a two-force member and both of them are in the opposite directions, and the truss is in equilibrium. And both of them are getting away from each other. The forces are called Select one: O a. The rotational forces O b. Tensile Forces O c. Parallel and collinear forces with same direction of heading O d. Compressive forces Next pag est-3 Jump to...
Use the graphical method to construct the shear-force and bending-moment diagrams for the beam shown. Let a = 5 m, b = 3 m, PB = 55 kN, Pc = 75 kN, and PE = 25 kN. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise. a PB Answer: Ay = i BO PB a B Pc a Calculate the reaction forces Ay and Dy acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since Ax = 0, it has been omitted from the free-body diagram.) D Pc D a D₂ PE a PE E kN, Dy= i -x E X kN.
Use the graphical method to construct the shear-force and bending-moment diagrams for the beam shown. Let o-1.5m.b=3.5 m.w=50 kN/m and P = 45 kN. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise. C Calculate the reaction forces A, and D, acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since A, -0, it has been omitted from the free-body diagram.) Answers: A, b KN, D, KN.
A hydraulic crane of total mass (including the mass of the boom) 53O0kg supports a load of 800kg. The boom mass 500kg is 7m long and makes an angle of 50 degrees with the horizontal. The boom's center of the boom length. Also assume that the center of mass of the crane excluding the boom acts at the middle of the outrigger jacks that are 4m apart. Draw the FBD of the crane and boom. Find the reaction force at the rear outrigger jack (Nr) and at the front (Nf) for the system to be in equilibrium. Assume the ground is friction less. 7m 1m
PART 1 Use the graphical method to construct the shear-force and bending-moment diagrams for the beam shown. Let a=3.5 m, b=2.0 m, PB = 2 kN, PC = 2 kN, and MB = 20 kN-m. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise. IMAGE* Calculate the reaction forces Ay and MA acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since Ax = 0, it has been omitted from the free-body diagram.) IMAGE* PART 2 Determine the shear force acting at each of the following locations:(a) x = 0+ m (i.e., just to the right of fixed support A)(b) x = 3.5– m (i.e., just to the left of B)(c) x = 3.5+ m (i.e., just to the right of B)(d) x = 5.5– m (i.e., just to the left of C)When entering your answers, use the shear force sign convention.Answer:(a) V = ? kN.(b) V = ? kN.(c) V = ? kN.(d) V = ? kN. PART 3…
Solve with complete Free Body Diagram.
Use the graphical method to construct the shear-force and bending-moment diagrams for the beam shown. Let a=4.0 ft, b-9.0 ft. c=4.0 ft, d=3.0ft, w=8 kips/ft and P = 66 kips. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise. B B ÎÎÎÎÎÎ Answers: Ay=i b d For this loading, calculate the reaction forces Ay and Ey acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since Ax = 0, it has been omitted from the free-body diagram.) W C b C C D E kips, Ey = i E X Ey kips.