A concrete column carries an axial load of 450 kN and a bending moment of 60 kN-m at its base. An isolated footing of size 2 m x 3 m, side 3m along the plane of the bending moment, is provided under the column. Centres of gravity of column and footing coincide. The net maximum and the minimum pressures in kN/m2 on soil under the footing are respectively

A concrete column carries an axial load of 450 kN and a bending moment of 60 kN-m at its base. An isolated footing of size 2 m x 3 m, side 3m along the plane of the bending moment, is provided under the column. Centres of gravity of column and footing coincide. The net maximum and the minimum pressures in kN/m2 on soil under the footing are respectively

Principles of Foundation Engineering (MindTap Course List)

9th Edition

ISBN:9781337705028

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter10: Mat Foundations

Section: Chapter Questions

Problem 10.2P

See similar textbooks

Similar questions

2 m 3m 75 EV 1 m A The footing plan is shown loaded uniformly in a rectangular area. What is the value of the increase of stress of the second or loaded area (Aσ₂) to be subtracted?
A 46-kN axial load P is applied to a short wooden post that is supported by a concrete footingresting on undisturbed soil.a. Determine the maximum size of the footing for which the average bearing stress in the soi is141kPa. b. Determine the maximum bearing stress on the concrete footing.
An eccentric footing shown has the following loads which acts on the center of the column: Pdl=400 kN Pll=650 kN Thickness of footing is 400mm f'c= 29 MPa; fy =420 MPa db=20mm Calculate the following: 1. The minimum and maximum soil pressure due to service loads 2. The minimum and maximum soil pressure due to factored loads
A column 500 mm x 500 mm square is supported by a 3.5 m x 3.5 m isolated spread footing. The column carries a dead load of 1200 kN and a live load of 1000 kN. The total depth of the footing is 550 mm with steel cover of 100 mm. Use NSCP 2001 provisions. Determine the punching shear stress at ultimate loads. A 1830.00 kPa 2154.11 kPa 1566.48 kPa D 1331.52 kPa
A 2.0 m 2.0 m square pad footing will be placed in a normally consolidated clay soil to carry a column load Q. The depth of the footing is 1.0 m. The soil parameters are: c = 0, =26, = 19 kN/m3, cu = 60 kN/m2 (=0 condition). Determine the maximum possible value for Q, considering short-term and long-term stability of the footing.
A square footing (B B) must carry a gross allowable load of 1160 kN. The base of the footing is to be located at a depth of 2 m below the ground surface. If the required factor of safety is 4.5, determine the size of the footing. Use Terzaghis bearing capacity factors and assume general shear failure of soil. Given: = 17 kN/m3, c = 48 kN/m2, =31.
Refer to the rectangular combined footing in Figure 10.1, with Q1 = 100 kip and Q2 = 150 kip. The distance between the two column loads L3 = 13.5 ft. The proximity of the property line at the left edge requires that L2 = 3.0 ft. The net allowable soil pressure is 2500 lb/ft2. Determine the breadth and length of a rectangular combined footing.
Calculate the intensity of stress below the centre of footing at depth of 8m due to load of 2000 KN/m² over the footing area of 5 mx 5 m. (Consider 2V: 1H Spread)
GEOTECHNICAL ENGINEERINGFind the value of B if the Allowable load for the footing Qa = 580KN
An R.C. Column footing 2.26 m in square shape is to rest 1.5 mbelow level ground level is on cohesive soil. The unit weight is17.6kN/m3. What is the safe load if cohesion is 30kN/m3Factor of safety 2.4? Angle of internal friction 33° by IS code.
90 A square footing 4m on a side 1.2m below the ground surface for which the bulk unit weight of the soil is 20KN/m3. The cohesion of the soil is 14kPa and the angle of internal friction is 30degrees. Consider the condition of the general shear failure and evaluate the contribution of the following soil bearing capacity. Use the given Chart for the determination of the bearing capacity factors. 80 70 +No 60 - Nq Nr a. Cohesion Strength. b. Soil Overburden Strength. c. Footing Dimension Strength. 50 40 30 20 10 10 20 30 40 50 Friction Angle Nc, Nq, Nr
An RC square footing of side length 2 m and uniform effective depth 200 mm is provided for a .300 mm x 300 mm column. The line of action of the vertical compressive load passes through the centroid of the footing as well as of the column. If the magnitude of the load is 320 kN, the nominal transverse (one way) shear stress in the footing is