a) Consider the following circuit. Assume that the diode is modeled with an ideal diode model. Determine Vo and ID. Show your work! 7V | R TV | 1k 12.5 V 1k ¡Vo w 1k + ¡Vo b) Consider the following circuit. Assume that the diode is modeled with a constant offset model with Von = 1V. Determine Vo and ID. Show your work! + 1k * 1k ☆ 1k ☆ kt 1k 1k KH c) Consider the following circuit. Assume that the diode is modeled with a constant offset model with Von = 1V. Determine Vo and ID. Show your work! ¡Vo 1k KH + 4V 4V 4V

a) Consider the following circuit. Assume that the diode is modeled with an ideal diode model. Determine Vo and ID. Show your work! 7V | R TV | 1k 12.5 V 1k ¡Vo w 1k + ¡Vo b) Consider the following circuit. Assume that the diode is modeled with a constant offset model with Von = 1V. Determine Vo and ID. Show your work! + 1k * 1k ☆ 1k ☆ kt 1k 1k KH c) Consider the following circuit. Assume that the diode is modeled with a constant offset model with Von = 1V. Determine Vo and ID. Show your work! ¡Vo 1k KH + 4V 4V 4V

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

For the circuit shown in the figure below, consider the diode as an ideal diode & R.M.S value of source voltage as Vs. The output voltage waveform at R is most likely to have zero value in the positive half cycle and a peak value of 1.414Vs in the negative half суcle sine-wave nature with a peak value 1.414VS zero value in the negative half cycle and a O peak value of 1.414Vs in the positive half сycle O sine-wave nature with a peak value Vs
3) Demonstrate clipping of negative waves with an inverted diode in the output. A circuit which removes the peak of a waveform is known as a clipper. Show a negative clipper. Produce a schematic diagram with LTspice schematic capture program. During the positive half cycle of the 5 V peak input, the diode is reversed biased. The diode does not conduct. It is as if the diode were not there. Show the positive half cycle is unchanged at the output V(2). Show the output positive peaks overlays the input sinewave V(1). Use in the LTSPICE display module, the command "plot v(1)+1)" accomplishes this. Voltage values: Resistor valuse: 1 ΚΩ DC offset: 0 V Amplitude: 5 V Freq: 1 KHz
V, is a 60Hz source with a peak voltage VP-120V is feeding a rectifier, assume ideal diode. The load resistance has a value of R= 10 k0. If ripple voltage Vr = 2V, the Diode average current Ipavg is VI Select one: a. + e. None Ob. 580mA Oc. 850mA Od 245mA 425mA D C: www tu Vo Q6
Consider a junction diode has dc biased current at operating point ID=0.8 mA. A sinusoidal voltage is superimposed on the VD such that the peak-to-peak sinusoidal current id(t) = 0.05ID. Find the value of the applied peak-to-peak sinusoidal voltage vd(t).
3: Using silicon diode design a clamper that will produce output V,-20Sin wt+10 (v) when the input voltage is Vo=20Sin wt-10 (V).Draw the circuit diagram and the input and output signals. 4:The 6-V zener diode has a maximum rated power dissipated of 690 mw.Its reveres current must be at least 3mA to keep it in breakdown. Find a suitable value for Rs if V; can vary from 9v to 12v and Ri. can vary from 5000 to 1.2KO.
• A Si diode at a temperature of 25°C has VD = 0.7V at Is = 10nA. The temperature is raised to 125°C. 1. Calculate ID at 25°C. 2. What is effect of rise in temperature on VD & IS 3. Calculate ID at 125°C.
Considering a clamper circuit, where capacitance C, load R, the built-in voltage of diode are unknown, which is the correct statement? The DC level shifts up The DC level of the signal changes The shape of signal changes The peak-to-peak value of signal changes
For the diode applied in the circuit has a knee current of 5mA, and a maximum allowed power dissipation of 300mW. What are the maximum and minimum load currents that can be drawn safely from the circuit with constant voltage output Vo of 6V?
For the circuit shown below, sketch to scale the output V waveform and draw the transfer characteristic (V versus Vi), Assume the diodes are ideal.
Consider a silicon pn junction diode at T 300K. The reverse saturation current is Is = 10-14 A and the ideality factor n = 1. Determine the diode current for a diode voltage of VD = 0.573 V and use that to determine the DC and AC resistance of the diode. RDC = 14.13 k rac = 639 Q RDC = 234 Q2 = rac=8Q RDC = 7.00 KQ rac = 307 Q RDC = 1.43 kQ rac = 58 Q
A silicon diode is in connected to a DC voltage source with Forward biased, the net currentflowing through the diode is (25mA) where the applied voltage across the terminals of thediode is (820mV). Determine diode temperature, if Is "dark saturation current", the diodeleakage current density in the absence of light is 3.4 × 10−10 A
Analyze the ON/OFF states of all diodes (D1 and D2) inthis circuit, using the ideal-diode model.