A cylindrical specimen of aluminum having a diameter of (10 mm) and a gauge length of (60 mm) is pulled in tension. Use the load - elongation characteristics tabulated below to complete problems a through e. a. Plot the data as engineering stress versus engineering strain. b. Determine Young Modulus c. Determine the yield strength at a strain offset of 0.002. d. Determine maximum tensile strength of this alloy. e. What is the approximate ductility, in percent elongation? Load(P) 0 6.32 9.48 15.8 22.15 22.11 22.05 25.27 28.43 25.27 20.5 (KN) Elongation(AL) 0 0.002 0.9 1.1 1.98 2.1 2.383 7.62 11.91 20.2 21.9 (mm)

A cylindrical specimen of aluminum having a diameter of (10 mm) and a gauge length of (60 mm) is pulled in tension. Use the load - elongation characteristics tabulated below to complete problems a through e. a. Plot the data as engineering stress versus engineering strain. b. Determine Young Modulus c. Determine the yield strength at a strain offset of 0.002. d. Determine maximum tensile strength of this alloy. e. What is the approximate ductility, in percent elongation? Load(P) 0 6.32 9.48 15.8 22.15 22.11 22.05 25.27 28.43 25.27 20.5 (KN) Elongation(AL) 0 0.002 0.9 1.1 1.98 2.1 2.383 7.62 11.91 20.2 21.9 (mm)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Stress Strain Diagram The Data shown in the table have been obtained from a tensile test conducted on a high-strength steel. The test specimen had a diameter of 0.505 inch and a gage length of 2.00 inch. Using software. plot the Stress-Strain Diagram for this steel and determine its: A= TTdT(050s A %3D 1. Proportional Limit, 2. Modulus of Elasticity, 3. Yield Strength (SY) at 0.2% Offset, 4. Ultimate Strength (Su), 5. Percent Elongation in 2.00 inch, 6. Percent Reduction in Area, 7. Present the results (for Steps 1-6) in a highly organized table. e Altac ie sheet (as problelle 4 A = 0.2.002 BEOINNING of the effort Elongation (in) Elongation (In) Load Load #: #3 (Ib) (Ib) 1 0.0170 15 12,300 0.0004 1,500 16 12,200 0.0200 0.0010 3. 3,100 17 12,000 0.0275 0.0016 4,700 18 13,000 0.0335 5. 6,300 0.0022 19 15,000 0.0400 0.0026 6. 8,000 20 16,200 0.055 0.0032 9,500 21 17,500 0.0680 0.0035 8. 11,000 22 18,800 0.1080 0.0041 11,800 23 19,600 0.1515 0.0051 24 20,100 0.2010 10 12,300 0.0071 25…
The proof stress of a material under tensile loading can be considered as can be considered as equivalent to the ultimate tensile strength for aluminium alloys being only applied to engineering steels during a tensile test the intercept on the stress stain curve for a given strain where a line draw is parallel to the elastic response line. the stress at yield for materials have no defined yield stress
Example: Convert the change in length data in Table 3-2 to engineering stress and strain and plot a stress-strain curve Homework- help Table 3-2 The results of a tensile test of a 0.505 in. diameter aluminum alloy test bar, initial length (1o) = 2 in. Calculated LTO Load (Ib) Change in Length (in.) Stress (psi) Strain (in./in.) 0.000 1000 0.001 0.0005 4,993 14,978 24,963 34,948 37,445 39,442 39,941 39,691 37,944 3000 0.003 0.0015 5000 0.005 0.0025 7000 0.007 0.0035 7500 0.030 0.0150 7900 0.080 0.0400 8000 (maximum load) 0.120 0.0600 7950 0.160 0.0800 7600 (fracture) 0.205 0.1025
*O llAsiacell Strength of m. -> 02: A steel specimen 12mm diameter has gauge length 50mm. the steel specimen had tested via tensile test under maximum load 66KN with elongation 7.5mm, and the yield load of this specimen is 15KN with elongation 2.4mm. Calculate: 1- The engineering ultimate stress (ultimate tensile strength), and engineering strain at this point. 2- The engineering stress and strain at yield point. 3- The modulus of elasticity, and the modulus of resilience. 4- The final or fracture strain of a steel specimen, if you know that the final length of specimen after testing is 58.5mm. 5- The true stress and strain for ultimate point. Q3: The yoke-and-rod connection is subjected to a tensile force of 15 kN. Determine the average normal stress in each rod and the average shear stress in the pin A between the members. Finally, find the shear strain in pin A. Take G teef 75GPA 40 mm 15 kN, 30 mm 30 mn 15 kN 04: In figure as shown below, assume that a 35mm diameter rivet joint the…
. From the tensile stress-strain behaviour for a casted iron as shown in the following curve. Please answer the following questions (1) Estimate the modulus of elasticity, (2) Calculate the change in length of a specimen with original length of 100mm that is subjected to a tensile stress of 300MPa. (Hint: Using the Hooke's law to get the strain.) 600 500 400 - 300 - 200 - 100 - 2 4 6. 8 10 12 14 16 Strain Strength (MPa)
Question A cylindrical specimen of metal having a diameter of 12.88 mm and a gauge length of 63.50 mm is tested using a tensile testing machine. The elongation measurement are recorded in Table 3. nPlot the stress-strain curve on the graph paper provided based on data in Table 3 Based on the stress-strain curved plotted in (i): Compute the modulus of elasticity Determine the yield strength at a strain offset of 0.002. Determine the tensile strength Determine the ductility in percent elongation and percent area reduction Table 3: Load-elongation readings for a metal specimen Jadual 3: Bacaan beban pemanjangan untuk statu spesimen logam) Load (N) Elongation (mm) 1380 0.03 2780 0.06 5630 0.12 7430 0.2 8140 0.25 9870 0.64 12850 1.91 14100 3.18 14340 4.45 13830 5.72 12500 6.99 Fracture
A specimen with an initial diameter of 12 + b* was tested under tensile conditions and a maximum load of 60 kN was recorded together with a %65 of strain. What should be the load to be applied in order to obtain a strain of %30
Example A cylindrical specimen of aluminum having a diameter of 0.505 in. (12.8 mm) and a gauge length of 2.000 in. (50.800 mm) is pulled in tension. Use the load- elongation characteristics tabulated below to complete parts (a) through (). Load Length Ib in. (a) Plot the data as engineering stress 50.800 2.000 7,330 1,650 50.851 2.002 versus engineering strain. 15,100 3,400 50.902 2.004 (b) Compute the modulus of elasticity. 23,100 5,200 50.952 2.006 30,400 6,850 51.003 2.008 (c) Determine the yield strength at a strain 34,400 7,750 51.054 2.010 offset of 0.002. 38,400 8,650 51.308 2.020 41,300 9.300 51.816 2.040 (d) Determine the tensile strength of this 44,800 10,100 52.832 2.080 46,200 10,400 53.848 2.120 alloy. 47,300 10,650 54.864 2.160 (e) What is the approximate ductility, in 47,500 10,700 55.880 2.200 46,100 10,400 percent elongation? 56.896 2.240 44,800 10,100 57.658 2.270 ) Compute the modulus of resilience. WILEY Chapter 8- 51 42,600 9,600 58.420 2.300 36,400 8,200 59.182…
The table below shows the deformation data that resulted from applying a pure tensile load to a brass alloy rod with an initial length of 30 mm and a diameter of 10 mm. This rod was subjected to necking and beyond necking deformation. The data at fracture is shown in the last row. Applied Load (N) Length (mm) Diameter (mm) 75,100 33.8 68, 250 34.9 50,200 35.7 6.7 Solve for the TRUE STRESS/ES and TRUE STRAINS. 8.3 7.8
Problem No. 2 The above load-elongation data were obtained for a specimen with Lo = 0.1 m and ro 7 mm. Plot the stress-strain data and determine the E, G, and of Load (KN) 0.0 12.8 36.7 43.5 47.0 50.1 61.4 71.6 74.2 71.6 67.6 Elongation (mm) 0 0.0201 0.0690 0.1173 0.1898 0.2864 1.1684 3.5052 7.3025 10.2235 13.7287
Force P and length change AL data are given in table below for the initial portion of a tension test on 7075-T651 Al alloy. The diameter before testing was 9.07 mm., and the gage length Linitial for t length change measurement was 50.8 mm. Determine the yield strength with offset limit, and %total elongation. P, kN AL mm 7.22 14.34 0.0839 0.1636 21.06 0.241 26.8 0.308 31.7 0.380 34.1 0.484 35.0 0.614 36.0 0.924 36.5 1.279 36.9 1.622 37.2 1.994
The following stress-strain curve was prepared based on a tensile test of a specimen that had a circular cross-section. The gage diameter of the specimen was 0.25 inches and the gage length was 4 inches. The stress scale of the stress-strain diagram is given with the factor a = 10 ksi. Estimate: (a) The modulus of elasticity. (b) The ultimate strength. (c) The yield strength (0.2% offset). (d) The percent elongation at fracture. 2013 Michael Swanbom STRESS VS. STRAIN BY NC SA 7a bat Sat 2at at 0.05 STRAIN 0.01 0.04 0.06 0.08 0.02 0.03 0.07 0.09 STRESS