A drum 6 inches in diameter and 40 inches long contained acetylene at 250 psia and 80°F. After some of the acetylene was used the pressure was 200 psia and the temperature was 70°F (a) what portion of the acetylene was used, and (b) what volume would the used acetylene occupy at 14.7 psia and 60°F. R(acetylene) = 59.35 ft-lbf/lbm-R Answer: a. b. V = % mass

A drum 6 inches in diameter and 40 inches long contained acetylene at 250 psia and 80°F. After some of the acetylene was used the pressure was 200 psia and the temperature was 70°F (a) what portion of the acetylene was used, and (b) what volume would the used acetylene occupy at 14.7 psia and 60°F. R(acetylene) = 59.35 ft-lbf/lbm-R Answer: a. b. V = % mass

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1. If 1 gallon of oil = 1.4 therm, how many gallons have been wasted by heat loss in Feb? (1 therm = 100,000 BTU)_____________________________________________________________________________________2. If $1.30 per therm, how much did you waste from house heat loss in Feb?
SG of Water=1.0 SG of Mercury=13.6 SG of n-Octane=0.65
A drum 0.5 ft in diameter and 45 inches long contained acetylene at 350 psia, 90 oF. After some of the acetylene was used, the pressure was 200 psia and 85 oF. a) determine the amount of acetylene that was used (lbm). b) What volume would the used acetylene occupy at 14.7 psia, 80 oF (ft3) ? R for this gas is 59.35 ft-lbf/lbm-R.
Identify if the property of the following steam: Temp Pressure Specific Volume C MPa m3/kg ? 3 0.001213
What is the piston work for this process in kJ? (КРа) 2 200 5 V (m³) 3 Select one: O 200 O 400 O - 200 -400
Answer the following questions, in the provided space in the table: Question Solution & Answer 1. A l-m' rigid tank contains 10 kg of water (in any phase or phases) At 160'C. The pressure in the tank is ? 2. What is the boiling temperature Of water at 175 kPa? 3. What is the state of H.O at 1554.9 kPa and 200 C? 4. What is the state of water at 300 C and 0.2 MPa? 5. What is the state of water at 0.01 C and 0.5 kPa? 6. What is the triple point? 7. What is the density of Compressed liquid-water at 500 kPa and 100 C? 8. What is the amount of heat required to evaporate 1 kg of saturated liquid water at 1000 kPa?
Suppose there are two identical gas cylinders. One contains the monatomic gas krypton (Kr), and the other contains an equal mass of the monatomic gas radon (Rn). The pressures in the cylinders are the same, but the temperatures are different. Determine the ratio KEr /KERN of the average kinetic energy of an atom of krypton to the average kinetic energy of an atom of radon. The answer should be a value.
26. The nitrogen gas a volume of 25.4ml in a tube at a 18°C and a pressure of 781mmHg. The next day the volume of the nitrogen was 26.2mL with the barometer still reading 781mmHg. What was the temperature on the second day? a. 67.3915°C b. 27.1701°C c. 52.8385°C d. 68.5611°C 27. A crystal of a chemical sodium weighs 6.48g in air and 2.83g when immersed in a fluid having a specific gravity of 0.868. What is the density of this element? a. 1.5718g/cm³ b. 1.5623g/cm³ c. 1.5321g/cm³ d. 1.5410g/cm3 28. A 5.2m³ container contains 72 % of methane and 28% of nitrogen gas mixture with an equal mass of 0.5kg. Find the pressure at 30°C. a. 26.0386kPa b. 24.8829kPa c. 26.5320kPa d. 25.0372kPa 29. An electric stove having a rating of 3kW is use to boil a 10Li of tap water (Initially at 20°C and whose density at this temperature is 1050kg/m³). If useful energy is around 76% of the total energy supplied by the stove. Determine how long would it take to vaporized all the water in the pan. a. 3.2hours…
FOLLOW THESE STEPS FOR UPVOTE Given Required Diagram Solution Conclusion Do not round off while solving. Question: To compensate the possibility of bursting in a 300,000 Li tank containing octane initially at 25°C, it was integrated by a movable roof that allows the expansion of the gas inside. If the designed temperature of the tank during the operation varies between 15°C and 50°C and the diameter of roof is 5000 mm, determine the displacement (millimeters) of the roof during the minimum and maximum operating temperature assume that the pressure remains constant at atmospheric value for safety reason.
What is the critical pressure of R-134a, in kPa?
Describe the supercritical pressures (P > Pcr), there is no distinct phase-change (boiling) process.
Complete the following table for Refrigerant-134a. Use the data from the steam tables exactly as listed.