A four wire, three phase system has a balanced supply voltage of 208V. Three wattmeters are connected to measure the power dissipated on the three resistors. Calculate for a) Neutral Voltage b) Line currents c) readings of wattmeter d) total power of the load W (W) 2002 40 $120 Figure 2. Question number 5

A four wire, three phase system has a balanced supply voltage of 208V. Three wattmeters are connected to measure the power dissipated on the three resistors. Calculate for a) Neutral Voltage b) Line currents c) readings of wattmeter d) total power of the load W (W) 2002 40 $120 Figure 2. Question number 5

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.28P: For the system shown in Figure 3.34. draw an impedance diagram in per unit by choosing 100 kVA to be...

See similar textbooks

Similar questions

Q2/ Find Yous for the power system all reactance on a common base. Bus 3 j0.25 j0.10 j0.25 Bus 2 j0.125 Bus 1 j0.40 j0.20 j0.10 Bus 4
The format of the answer will be for rectangular form is 174+j40. use 4 decimal place *What is the admittance of if the impedance is 37+j1 ohms? *A load of 1+ j35 is connected across a 220 volts source. Determine the current.
The main advantage of A.C. systems over D.C. systems is: a) transformers can be used to change D.C. to A.C. IRtransformers can be used to change voltage levels. b) , 00 transformers can be used to change A.C. to D.C. d) ) transformers can be used to change power levels.
1. A resistor, in series with a 138-microfarad capacitor, is connected to a 60-cycle source. If the voltage drop across the capacitor is 115 volts and the power taken by the circuit is 922 watts, calculate (a) the circuit current, (b) the ohmic value of the resistor, (c) the line voltage, (d) the circuit power factor. Please show complete solution and the circuit diagram. Please round off answers up to the 3rd decimal place. Thank you!
I. PROBLEM SOLVING. The following are data pertaining to three units in a plant: Unit 1: Min: 150 MW Max: 600 MW C(1) = 0.01562 P₁2 + 79.2 P₁ + 5610 $/br Unit 2: Min: 100 MW Max: 400 MW C(2) = 0.0194 P₂² + 78.5 P2 + 3100 $/br Unit 3: Min: 50 MW Max: 200 MW C(3) = 0.05784 P3² +95.64 P3 + 936 $/br What unit or combination of units should be used to supply a load of 550 MW most economically? Support your answer with solution.
Problem 5 For two electrical system shown in Figure 5, use cyclic currents to derive a complete mathematical model for each of the electrical systems. Ri. Rz ca) Cz (6) ERZ RI
A wattmeter with a current coil connected to phase A, and the voltage between phase A and C gives a reading of 280 kW in a three-wire three-phase system. Three ampmeters arranged lines A, B and C indicate respectively 140, 110 and 130 Amps. The voltage of line measured by a voltmeter gives 2300 volts between any pair of lines. Make the corresponding diagram, indicating the connection of the instruments to finally calculate the active power of the system
Q1. In a 3-phase 4 wire, 400/230 system, a lamp of 100 watts is connected to one phase and neutral and a lamp of 150 watts is connected to the second phase and neutral. If the neutral wire is disconnected accidentally, what will be the voltage across each phase? Do you think it will affect their performance? Explain
17 In the figure shown, the voltage V1 the voltage V2 by V₁ * out of phase. 40)
(b) A symmetrical three-wire three-phase supply as shown in Figure Q2(b) is connected to a balanced three-phase load. The value of impedance, Z is identified to be 100-j75 Q. (i) Find IaB, IBC and ICa (ii) Determine Iaa, IbB and Ic (iii) Determine Iba, Isb and Ix (iv) Draw the phasor diagram of all currents in Q(b)(i) and Q(b)(ii)
Q6 the busbars of a power station are in two sections a and b separatedvby acreactor. connected in section a arevtwo 12 mva generators of 15% reactance each andvto b, 8 mva generator of reactance 10%. the reactor is rated 8 mva and 15 % reactance. two feeders are connected to busbar a through transformers, each rated at 4 mva and 5 % reactance. determine the maximum short circuit mva with which circuit breakers on the outgoing side of the transformers have to deal Full explainthe this question very fast solution sent me step by step Don't ignore any part all part work u Not:- Text typing work only not allow paper work
Problem 223: EE Board March 1998 A load of 20 + j35 ohms is connected across a 220 volts source. Determine the power factor and the VARS.