A half bridge resonant inverter with bidirectional switches is connected to a load resistor consuming a power of 10KW, with rms andaverage transistor currents being as: 15.81 A and 22.72 A. If a half bridge resonant inverter with unidirectional switches is connected tothe same load and providing the same power, then the rms and average transistor currents will be:Select one:O a. 11.17A, 45.44Ab. 15.81A, 22.72AO c. 22.358A, 45.44.AO d. None of theseO e. 7.905.A, 22.72A

Step 1:So, the correct answer is option B15.81 A , 22.72 A

Answered: A half bridge resonant inverter with…

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

a. In AC, how are the capacitors treated? b. In AC, how are DC sources treated? c. What is the amplifier configuration of Figure 4? d. What is the expected phase shift of the sinusoidal input at the output side? e. What is Zi across RG, the gate resistor? f. It is the IC in its smallest form. g. The most commonly used metal as interconnect of the chip to external peipheral. h. How is pin 1 of the chip determined? i. An IC package similar to a DIP but with the pins bent outward. j. Which sensors are packed as IC?
Set up a midpoint bias for a JFET with IDSS = 14 mA and VGS(off) = -10 V. Use a 24 V dc source as the supply voltage. Show the circuit and resistor values. Indicate the value of ID. Indicate the value of VGS. Indicate the value of VDS.
1) what is the Voltage & Current rating ofTriode for Alternating Current (TRIAC) 2) 5. Are the following statements correct or wrong? Justify your answer.(a) Thyristors are used only for low voltage, low current applications.(b) MOSFETs are used for high frequency applications.(c) BJT is more efficient than IGBT in high power applications.(d) GTO requires very low current applied to its gate to be turn off.(e) IGBT is a voltage driven device.
In the VI characteristics of JFET When Vgs=0, 1..When we increases the Vds,Id is also increases.(width of deplation region cannot change ) In this case Vds and Id are proportional by ohms law. This is ohmic region 2.. but after a perticular pt. (Pich off voltage)When Vgs Is zero. Id=Idss and is constant (as Vds goes on Increasing Vgd set such width off deplation region to Id become constant) This is active region of JFET 3 but on further Increasing Vds , Id starts suddenly increase (breack down condition) What reason this should happen?
Offset voltage compensating network is connected in between pin number .......... &.. of LM741 op-amp .... O 1 and 4 O 1 and 5 O 2 and 3 O 4 and 7
........ (Figure-1) R. RB= 380kN,Rc= 1kN B = 100, VBB = Vcc=12V RB ww Vec CC ......... I, V CE СЕ V ВЕ BB Q-1-b) Describe briefly the input / output characteristics and application of Common Emitter BJT Configuration
Identify the source, drain, gate, and bulk terminalsand find the current I in the transistorsAssume VTN = 0.70 V
3. A single-phase to single-phase cycloconverter "bridge type" with input voltage and frequency 150V and 50Hz. respectively. The output frequency is 10Hz and the firing angle equal to 45°. The load is resistance with the value of 1002 in series with reactive inductance of the value of 20mH. Assume the extinction angle equal 180°. a. Draw the waveforms output voltage, output current, source current, the thyristors currents (iT, IT, IT and in) b. Calculate the rms of output voltage. c. The rms current of each thyristor. d. The input power factor
Determine the value of Zbase for the circuits.
Question 2 a) Briefly explain the de chopper, inverter, controlled rectifier and ac voltage controller. b) A buck-boost regulator as shown in Figure 2 has an input voltage, Vs = 12 V. The duty cycle, k = 0.35 and the switching frequency is 30 kHz. It also has an inductance, L = 200 µH, filter capacitance, C = 440 µF. The average load current, Ia 1.25 A. Determine the: i. average output voltage, Va, ii. peak-to-peak output ripple voltage, AVc, iii. peak-to-peak output ripple current of inductor, AI, iv. peak current of the transistor, Ip, V. critical values of L and C, and vi. critical values of L and C if Vs is increased to 14 V. Estimate the change in percentage for the critical values of L and C. is Vs C Load Vo, Vs VC i, Ia Figure 2
QUESTION 1 By referring to Figure Q1, determine: a) The Q-point values of Ic and VCE. b) Draw the DC load line and plot the Q-point based on answer from Q1(a). c) The diode emitter resistance, re and draw re transistor model (AC equivalent circuu). d) The input impedance, Zi as seen from the input voltage. e) The output impedance, Z, as seen from output. f) The voltage gain, Av and the current gain, A¡.
The juncon between the emitter and the base of a transistor is called: O a. Emitte Junction O b. Collector Junctien Oc Gate Junction O d. Base Junction

SEE MORE QUESTIONS

Recommended textbooks for you

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Fundamentals of Electric Circuits

Electrical Engineering

ISBN:

9780078028229

Author:

Charles K Alexander, Matthew Sadiku

Publisher:

McGraw-Hill Education

Electric Circuits. (11th Edition)

Electrical Engineering

ISBN:

9780134746968

Author:

James W. Nilsson, Susan Riedel

Publisher:

PEARSON

Engineering Electromagnetics

Electrical Engineering

ISBN:

9780078028151

Author:

Hayt, William H. (william Hart), Jr, BUCK, John A.

Publisher:

Mcgraw-hill Education,

SEE MORE TEXTBOOKS