A heat exchanger was installed purposely to cool 0.50 kg of gas per second. Molecular weight is 28 and k=1.32. The gas is cooled from 150⁰C to 80⁰C. Water is available at the rate of 0.30 kg/s and at a temperature of 12⁰C. Calculate the exit temperature of the water.
Q: (7)Steam enters an insulated long pipe, as in the figure, at 1600 kPa and 300°C and leaves at 1400…
A: Given: Inlet pressure P1=1600kPa Inlet temperature T1=300°C Outlet pressure P2=1400kPa Outlet…
Q: Aroomiscooledbycirculatingchilledwaterthroughaheatexchangerlocatedin a room. The air is circulated…
A: Given data as per question shaft output =0.25 hp Efficiency =54%
Q: In general, heat exchangers with higher flow rates have greater capacities?
A:
Q: Q=2000J Vout =? m (kg/s) D=0.1m air Air at (4.75x10^2) K flows out of a circular pipe at 101325 Pa…
A: Using ideal gas equation P=rho*R*T 101325=rho*287*475 Rho(density)=0.7433kg/m^3
Q: FIRST LAW OF THERMODYNAMICS CONSERVATION OF ENERGY – OPEN SYSTEM An air compressor is designed to…
A:
Q: PROBLEM 1: An air compressor is designed to compress atmospheric air (assumed to be at 100 kPa,…
A:
Q: Q: Five hundred kilograms per hour of steam drives a turbine. The steam enters the turbine at 44 atm…
A: ...
Q: The turbine's inlet is coupled to a steam throttling valve with inlet conditions of 2MPa and 400C.…
A: Write the given data. P1=2 MPaT1=400 °CW=200 kWQR=100 kWT2=300 °Cm˙=1 kg/s
Q: CO2 gas at 1000 kPa and 500 K enters a 5 cm diameter pipe of circular cross section with a velocity…
A:
Q: SOLVE THE PROBLEM AND SHOW THE DETAILED SOLUTION A steam condenser receives 10 kg per second of…
A: To Find : The cooling water flow rate. Given : The mass flow rate is m˙s=10 kgs. The enthalpy of…
Q: b) Hot exhaust gas of a car engine is to be used to heat up water in a heat exchanger. The exhaust…
A:
Q: - In a heat exchanger, steam of 0.08 bar and a specific steam content of 95% is condensed. 381.6…
A: a.
Q: A shell-and-tube heat exchanger with 1-shell pass and 20–tube passes is used to heat glycerin in the…
A:
Q: Cold air enters the mixing chamber at 85°C and 105 kPa at a rate of 0.55 m /s, while warm air enters…
A:
Q: Cold water is heated from 10 °C to 43.33 °C in the annular space of a double‐pipe heat exchanger and…
A:
Q: Q=2000J Vout =? m (kg/s) D=0.1m air Air at (4.65x10^2) K flows out of a circular pipe at 101325 Pa…
A: Find the outlet velocity .
Q: Liquid benzene at 38 C with a vapor pressure of 26.4 kN/m2 and a density of 860 kg/m3 is to be…
A: Given data as per question Pv=26.4 KNm2Q=0.0025 m3sη=0.6ρ=860 kgm3D=0.0409 mΔpf=3.45…
Q: Q=2000J Vout =? m (kg/s) D=0.1m air Air at (4.75x10^2) K flows out of a circular pipe at 101325 Pa…
A:
Q: If the temperature difference across each radiator is 10 C, the mass flow rate of water in pipe LM…
A:
Q: At a certain pair in a reaction turbine, the steam eaves the fixed blade at a pressure of 3 bar with…
A: The answer is in below steps
Q: Water enters the pump of a steam power plant at 15 kPa and 50°C at a rate of 0.15 m3 /s. The…
A:
Q: Water vapor at a flow rate of 20000 kg / h enters a steam boiler with a specific volume of 150 kPa…
A:
Q: Water flows through a shower head steadily at a rate of 8 kg/min. The water is heated in an electric…
A: Write the given information.
Q: flow of 30 kg/s circulates through the system, and 7 kg/s are “bled” into the turbine and go to the…
A:
Q: Water flows through a shower head steadily at the rate of 8 kg/min. The water is heated in an…
A: Given: mass flow rate of water = 8 kg/min = (8/60) kg/s = 0.133 kg/s initial cold water inlet, Tc1…
Q: To preheat the water before entering the boiler, a feed water heater is used, as shown in the…
A:
Q: Q=2000J Vour =? m (kg/s) D=0.1m air Air at (5.25x10^2) K flows out of a circular pipe at 101325 Pa…
A: Calculate the inlet velocity. mi˙=ρAvimi˙=ρπ4di2vi0.0093=1.2π40.12vivi=0.9867 m/s
Q: Air (cp = 1.005 kJ/kg·°C) is to be preheated by hot exhaust gases in a crossflow heat exchanger…
A: Given: The specific heat is Cp =1.10 kJ/kg∙⁰C. The pressure and temperature at the entrance is…
Q: a saturated steam is to be condensed at temperature of 50 °C to produce a saturated water. The…
A:
Q: Calculate the entropy of steam at 60 psia with percentage moisture of 0.40. Properties of steam at…
A: Given data: Percentage of moisture in steam, m = 0.40. Specific entropy of saturated liquid, sf =…
Q: Hot exhaust gases of an internal combustion engine are to be used to produce saturated water vapor…
A: Write the given information.
Q: Hot fluid enters at a flow rate of 3 kg/sec with an inlet temperature of 150 C while cold fluid…
A: Heat is a form of energy that gets transferred from the high temperature region to the low…
Q: Water vapor enters an adiabatic turbine with a pressure of 7 MPa and a flow rate of 2kg / sec at a…
A:
Q: Steam in the condenser of a power plant is to be condensed at a temperature of 30°C with cooling…
A:
Q: Water at 90C is being pumped from a large storage tank at 1 atm abs at a rate of 0.189 m3/min by a…
A:
Q: Steam enters the condenser of a steam power plant at 30 kPa, a quality of 91% and a mass flow rate…
A:
Q: Water flows through two adiabatic turbines and a heat exchanger as shown in the picture. Hot air is…
A: INTRODUCTION : Turbine is a work producing device, by taking energy from the inlet either compressor…
Q: In general, heat exchangers with higher flow rates have greater capacities?
A:
Q: Steam enters a long, insulated pipe at 1200 kPa, 250°C, and 4 m/s and exits at 1000 kPa. The…
A: Given data as per question Pressure of steam at entry =1200 kpa Temperature at entry = 250°Cvelocity…
Q: In a steam-heating system, air is heated by being passed over some tubes through which steam flows…
A: Given data as per question Inlet pressure = 30 psia Inlet temperature = 4000 F Steam entry rate =…
Q: Steam is to be condensed on the shell side of a heat exchanger at 120°F. Cooling water enters the…
A: Given data: The temperature of the shell side of a heat exchanger is T = 120 oF. The entry…
Q: A heat exchanger was installed purposely to cool 0.50 kg of gas per second. Molecular weight of is…
A: k=1.32mG˙=0.50 kg/smW˙=0.30 kg/sTG1=150°CTG2=80°CTW2=12°CM=28
Q: Automobile air-conditioner gives up 18 kW at 65 km/h if the outside temperature is 35°C. The…
A: let C1 and C2 are constant V= velocity of air m˙a=C1VU=C2V-0.7U=200=C2650.7C2=10.76
Q: in a 10-m long center-current flow tubular heat exchanger, a liquid food, flowing in the inner pipe…
A:
Q: P.4.7 A heat exchanger is to consist of a number of tubes each 25 mm diameter and 5 m long arranged…
A:
Q: Cold water is heated from 10 °C to 43.33 °C in the annular space of a double‐pipe heat exchanger and…
A: Given, Tci = Inlet temperature of the cold water = 10°C Tce = Exit temperature of the cold water =…
Q: what is the resulting heat transfer area if the exchanger will be parallel flow?
A: To explain : what is the resulting heat transfer area in parallel flow . the rate of heat transfer…
A heat exchanger was installed purposely to cool 0.50 kg of gas per
second. Molecular weight is 28 and k=1.32. The gas is cooled from 150⁰C to
80⁰C. Water is available at the rate of 0.30 kg/s and at a temperature of 12⁰C.
Calculate the exit temperature of the water.
Step by step
Solved in 2 steps
- Ammonia and air pass through the heat exchanger. While the ammonia is entering as a superheated vapor at 16 bar pressure and 60C temperature it is leaving as a saturated liquid at the same pressure but unknown temperature. The ammonia mass flow rate is 400 kg/hour. Air is flowing backward and is heated from 17C to 42C at the constant pressure of 2 bars. NOTE: Find air properties from https://www.peacesoftware.de/einigewerte/luft_e.html a.Draw the sketch of the heat exchanger showing all thermodynamic parameters (P, T, etc.) Please show all steps of solutionThe air considered as the ideal gas flows through the compressor and heat exchanger at a volumetric flow rate of 26.91 m3 / min as shown in the figure. At the same time, a stream of liquid water passes through the heat exchanger. The information given in the figure is for continuous flow. Considering the compressor and heat exchanger as adiabatic and ignoring kinetic and potential energy changes, a) the power requirement of the compressor (kW) and the mass flow rate of the cooling water (kg / h),b) Calculate the entropy generation (kW / K) per unit time for the compressor and heat exchanger.Ammonia and air pass through the heat exchanger. While the ammonia is entering as asuperheated vapor at 16 bar pressure and 60C temperature it is leaving as a saturated liquid at thesame pressure but unknown temperature. The ammonia mass flow rate is 400 kg/hour.Air is flowing backward and is heated from 17C to 42C at the constant pressure of 2 bars.NOTE: Find air properties from https://www.peacesoftware.de/einigewerte/luft_e.html a. Draw the ammonia T-v diagram showing the stages, pressures, and temperatures b. How much heat is transferred from ammonia to air assuming no heat transfer to thesurroundings? c.Determine air mass flow rate Please show all steps in solution thanks
- SOLVE THE PROBLEM AND SHOW THE DETAILED SOLUTION A steam condenser receives 10 kg per second of steam with an enthalpy of 2,570-kJ/kg. The steam condenses into liquid and leaves with an enthalpy of 160kJ/kg. Cooling water passes through the condenser with temperature increases from 13 to 24 Calculate the cooling water flow rate in kg/s.The exhaust gas leaving an oil engine is passed through a heat exchanger which consist of tubes surrounding by water. The gas enters at 327 °C and leaves at 193 °C. The water enters the exchanger at 17 and leaves at 56 °C. If the mass flow rate of water is 2.54kg/min. Determine the mass flow rate of gas, take cp of the gas is 1.04 kJ/kg.Steam (water vapor) enters a stainless steel tube with inner diameter 4cm at 300°C and 60 bar absolute pressure, with a velocity of 8.00 m/s. The steam exits the tube at 300°C and 40 bar absolute pressure. a. Assuming the water vapor behaves as an ideal gas, calculate the steam mass flow rate and the change in kinetic energy (in Watts). b. Using the specific volume values from table B.7, calculate the steam mass flow rate and the change in kinetic energy (in Watts).
- Give the significance of volume coefficient. The volume coefficient of expansions of water at 373 K is 7.8 x 10-4 K-1. Calculate the change in entropy when the pressure is increased from 1 bar to 100 bar. At 373 K, density of water is 958 kg/m3 .At a flow rate of .5000 m3 / h, saturated air at a temperature of 2 ° C is heated sensibly up to a temperature of 40 ° C with the help of a heating coil. Find the amount of heat that should be given to the coil.A 10 m3 oxygen tank is at 15 °C and 800 kPa. The valve is opened, andsome oxygen is released until the pressure in the tank drops to 600 kPa.Calculate the mass of oxygen that has been released from the tank if thetemperature in the tank does not change during the process. R = 260 J/kg.°K.
- Steam at a rate of 200 kg/min enters a turbine at 350°C and 40 bar through a 7.5-cm internal diameter pipe. The turbine operation is adiabatic, and the effluent leaves as saturated water at 5 bar through a 5-cm diameter pipe. 1. Calculate the work produced by the turbine in kW. 2. What is the enthalpyand phase of the effluent stream? 21 If it leaves the turbine at 75C and 5 bar 22 If it leaves the turbine at 30C and 5 bar 7.5225kg/hr of air at 40 oC enter a mixing chamber where it mixes with 540kg/hr of air at 15 oC. Calculate the temperature of the air leaving the chamber assuming steady flow condition. Assume that the heat loss is neglectedThe stream of air and gasoline vapour,in the ratio of 14:1 by mass, enters a gasoline engine at a temperature of 30C and leaves as combustion products at a temperature of 790C. The engine has a specific fuel consumption of 0.3kg/kWh.The net heat transfer rate from the fuel-air stream to the jacket cooling water and to the surroundings is 35kW.The shaft power delivered by the engine is 26kW.Compute the increase in specific enthalpy of the fuel-air stream, assuming the changes in kinetic and potential energy to be negligible.