A hollow circular shaft transmits 25 horsepower while operating at a rate of 180 rev/min. Ifthe shear stress in the shaft is limited to 475O psi, find the smallest safe thickness (in inches)for the shaft if the outside diameter is 2.5 in and the angle of twist is limited to 8.75° with alength of 8 feet. Use G=12x106 psi for steel.

Answered: Image /qna-images/answer/6684113a-4334-4616-8cec-57fa507476d8.jpg

A hollow circular shaft transmits 25 horsepower while operating at a rate of 180 rev/min. If the shear stress in the shaft is limited to 4750 psi, find the smallest safe thickness (in inches) for the shaft if the outside diameter is 2.5 in and the angle of twist is limited to 8.75° with a length of 8 feet. Use G=12x10 psi for steel.

A hollow circular shaft transmits 25 horsepower while operating at a rate of 180 rev/min. If the shear stress in the shaft is limited to 4750 psi, find the smallest safe thickness (in inches) for the shaft if the outside diameter is 2.5 in and the angle of twist is limited to 8.75° with a length of 8 feet. Use G=12x10 psi for steel.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

an aluminum shaft is 6ft. and has toruq of 500 lb-ft. the shear stress is 6500 psi and the angle of twist must not go over 3 1/2 degrees in the 6ft. pick the economical shaft size.
A solid shaft consisting of steel and aluminum segments carries the torques T and 2T. Find the largest allowable value of T if the working shear stress is 14,000 psi for steel and 7,500 psi for aluminum, and the angle of rotation at the free end must not exceed 8 degrees. Use G = 12 x 10^6 psi for steel and G =4 x 10^6 psi for aluminum. Express your final answer in Ib.ft to the nearest whole number. Note: Do not include the unit in your answer. 27 2 in. 1.5 in. 3 ft B 2 ft |C 800mm 500mm
A shaft is used to transmit 67 kw at a speed of 2,281 rev/min. Using a maximum allowable shear stress of 57 MPa, find the shaft diameter in mm.
A hollow steel shaft, 5.5 ft long, has an outer diameter of 2.76 in. and an inner diameter of 1.48 in. The shaft is transmitting 193 hp at 104 rev/min. Determine the angle of twist of the shaft in degrees. Use G = 12000048 psi for steel. Round off the final answer to two decimal places.
A shaft is required to fail when the torque on the shaft is 182 N-m. Find the suitable diameter of the shaft if the maximum shear stress is 50 .
A solid steel machine shaft with safe shearing stress of 7000 psi transmits a torque of 10,500 in-lb. A square key is used whose width is equal to one-fourth the shaft diameter and whose length is equal to 1.5 times the shaft diameter. Find the shearing stress in the key in psi.
A solid circular shaft transmits 75 kW power at 200 rpm. Calculatethe diameter of the shaft and the maximum shear stress acting on it,if the twist in the shaft is not exceeding 1 º in 2 m length of the shaft.Take modulus of rigidity as 102 GPa.
The torque of 100 kip - ft is applied in the 16-ft-long hollow steel shaft. Note that the inner diameter of the shaft is two-thirds of its outer diameter D. If the inner diameter is 8 inches, find the angle of twist of the shaft. Use G = 12 x 10^6 psi for steel.
The figure shows an inboard engine, 8-ft long steel drive shaft, and propeller for a motor boat. The shaft is to be designed to safely transmit 200 hp at 3500 rev/ min. Determine the diameter of the smallest shaft that can be used and its corresponding angle of twist. For the steel, use a working shear stress of 12 000 psi and G = 12 x 106 psifind, a) diameter b) angle of twist
Find the diameter of the solid shaft. Torque = 190 kNm Maximum shear stress = 210 MN/m?
Determine the diameter of a solid steel shaft which will transmit 112.5 kW at 200 rpm. Also determine the length of the shaft if the twist must not exceed 1.5o over the entire length. The maximum shear stress is limited to 55 N/mm2. Take the value of modulus of rigidity = 8 x 104 N/mm2.
A solid shaft in a rolling mill transmits 30 hp at 100 rpm. Find the diameter in mm of the shaft so as not to exceed a shearing stress of 42 MPa and an angle of twist of more than 5 degrees in a length of 3 meters. G = 83 GPa