A horizontal wind turbine has been installed near the sea shore. (a) Estimate the mechanical power generation of this turbine using the fundamental equation of wind power. (b) Consider that in the morning the temperature of the turbine installation place is 20 °C, and air has a density of approximately 1.204 kg/m3. However, at noon, the temperature of the place is increased to 34°C. Then, estimate the change in mechanical power output of the wind turbine. (Consider all other parameters remain constant). (c)Calculate the highest possible electricity generation by this wind turbine at noon time. (d)If the installed wind turbine's turbine cost is RM450,000 which the rated power is 600 kW and the capacity factor is 28.54%, estimate the possible leve/ised cost of electricity for 30 years of operation .

A horizontal wind turbine has been installed near the sea shore. (a) Estimate the mechanical power generation of this turbine using the fundamental equation of wind power. (b) Consider that in the morning the temperature of the turbine installation place is 20 °C, and air has a density of approximately 1.204 kg/m3. However, at noon, the temperature of the place is increased to 34°C. Then, estimate the change in mechanical power output of the wind turbine. (Consider all other parameters remain constant). (c)Calculate the highest possible electricity generation by this wind turbine at noon time. (d)If the installed wind turbine's turbine cost is RM450,000 which the rated power is 600 kW and the capacity factor is 28.54%, estimate the possible leve/ised cost of electricity for 30 years of operation .

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.31P

See similar textbooks

Similar questions

A thermal engine uses up 200 J of heat energy per cycle, while its mechanicalwork output per cycle is 40 J. (a) What is this engine’s thermal efficiency? (b) If thisengine is utilized to lift a 100 kg mass to a height of 20 m, through how many cycles doesthe engine have to be run to perform the lift (the answer may not be an integer)? (Hint: tolift a weight to a height, mechanical work must be performed against gravity.) (c)Consider now an ideal thermal engine operating between a hot reservoir and a coldreservoir. Find the temperature (in 0 C) that would be required for the hot reservoir inorder to achieve the same efficiency as the engine in part (a) if the cold reservoir is atroom temperature (25 0 C).
How long should a rotor blade of a wind turbine be if it is designed to produce 10 kW and the prevailing wind speed is about 50 kph? Assume that air density is 1.20 kg/m3.
A wind generator that is 50 m in diameter is subjected to winds of 20 m/s. If the turbine has an efficiency of 40%, what is the power generated? and what is the force exerted by the wind?
Consider an automobile with a mass of 5500 lbm braking to a stop from a speed of 55 miles/h.(a) How much energy (Btu) is dissipated as heat by the friction of the braking process?(b) Suppose that throughout the United States, 300,000,000 such braking processes occur in the course of a given day. Calculate the average rate (megawatts) at which energy is being dissipated by the resulting friction.(c) Find a source of information on the average per-capita consumption of electricity (kW) in the United States, France, and India. Roughly how many people in each country would have their electricity needs met if the braking energy calculated in Part (b) could be recovered and used to provide electricity? Show your calculations and identify your information source.
A 30m diameter wind turbine is placed on a 50m tower in terrain with a power law coefficient (a) of 0.2. Find the ratio of available power in the wind at the highest point the rotor reaches to that at its lowest point.
2. At a certain location, wind is blowing steadily at 10 m/s. Determine the mechanical energy of air per unit mass and the power generation potential of a wind turbine with 60-m-diameter blades at that location. Take the air density to be 1.25 kg/m3. ất Region XI can utilize aside from hydroelectric power? 3. In your perspective, what are top three energy so Support your answer. ich the wind
Imagine a solar electric power plant that operates by using a gigantic mirror to concentrate light on the boiler for a steam engine. Assume that the boiler generates steam at a temperature of 515oC. The only possibility for a cold-temperature reservoir is a nearby creek that has an average width of 8 m and an average depth of 0.7 m, flowing at a rate of 0.6 m / s. What is the maximum electric power ( in MW ) that could be produced by the plant if it boils the entire creek dry? Assume the stream is at atemperature of 20oC and all heat is transferred to the stream at 100oC.The maximum electric power that could be produced by the plant is______ MW.
Dresden, Germany has a population of 700,000 and a population density of2200 km-2 in the urban area. Assume that the electrical needs of Dresden are an average of1.0 kWe per capita and these are satisfied by a wind farm consisting of 100 m diameterthree-rotor wind turbines operating at optimal efficiency and with optimal spacing. If thewind velocity is constant at 7 m/s, what is the area of the wind farm? The optimal efficiency, η = 0.49 and The ideal spacing for a turbine is 300m by 1000 meters Answer in km2
With a wind turbine whose blades sweep 28 m² in an area where the wind speed is 8 m/s.Calculate the mechanical power that can be obtained. (density of air = 1.35 kg/m³).
Calculate the power generation potential of a 55 m blade diameter wind turbine in a region where the wind speed is 8 m / s. Find the amount of electricity to be obtained when the system efficiency is assumed to be 30%. (p air = 1.25 kg / m3)
Consider an axial flow blower spinning at 4200 rpm with tip and hub diameters of 25 cm and 12.5 cm, respectively. The blower has no inlet guide vanes and the inlet and exit blade angles to the rotor are -75° and -55%, respectively. The inlet veloc- ity is purely axial. The mass flow rate is 0.466 kg/s and the static conditions at the inlet are 101.3 kPa and 35°C. Calculate the degree of reaction and stagnation and static pressure rises through the rotor.
A wind turbine that is 80 meters tall with a blade length of 160 ft will be used to generate electricity in an off-grid farm. The average annual wind speed in the area is 50 ft/s. Calculate the power in Megawatts that can be generated by the turbine with an efficiencyof 95%.