A hydro electric power station is used to supplement the unmet constant load demand for 2 hours and 30 minutes during peak periods.it has a reservoir of 0.03km2 area and 2.7 meters depth .The overall water in the reservoir can generate a total energy of 17236kwh at an effective head of 95 metres.after supplying the load.the reservoir depth has decreased by 20%. 6.Determine the overall efficiency of the power station 7.Determine the load consumptio(kWh) 8.Determine the volumetric flow rate(m3/s)

A hydro electric power station is used to supplement the unmet constant load demand for 2 hours and 30 minutes during peak periods.it has a reservoir of 0.03km2 area and 2.7 meters depth .The overall water in the reservoir can generate a total energy of 17236kwh at an effective head of 95 metres.after supplying the load.the reservoir depth has decreased by 20%. 6.Determine the overall efficiency of the power station 7.Determine the load consumptio(kWh) 8.Determine the volumetric flow rate(m3/s)

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.11P

See similar textbooks

Similar questions

Consider two interconnected voltage sources connected by a line of impedance Z=jX, as shown in Figure 2.27. (a) Obtain expressions for P12 and Q12. (b) Determine the maximum power transfer and the condition for it to
A generator operating at 50 Hz delivers 1 p.u. power to an infinite bus through a transmission circuit in which resistance is ignored. A fault takes place reducing the maximum power transferable to 0.5 p.u. Where as before the fault, this power was 2.5 p.u. and after the clearance of the fault, it is 2 p.u. The value of 8 is max
The peak load on a 50 MW power station is 39 MW. It supplies power through for transformers whose connected loads are 17, 12,9 and 10 MW. The maximum demands on these transformers are 15, 10, 8 and 9 MW respectively. The annual load factor is 50% and the plant is operating for 65% of the period in a year. 102. The average load on the station is (A) 50000 kW (C) 39000 kW (B) 19500 kW (D) 48000 kW. 103. The energy supplied per year is (A) 438 x 106 kWh (C) 170.82 x 106 kWh (B) 341.64 x 106 kWh (D) 420.48 x 106 kWh.
The reactance of a generator is given as 0.1 pu based on the generator of 17 KV, 300 MVA. Determine the pu reactance on a base of 17 KV, 250 MVA. New pu reactance is.......
Question A power plant has a maximum demand of 15 MW. The annual load factor is 50% and annual plant capacity factor is 40%. The operating reserve capacity is
For a power station, the yearly load duration curve is a straight line from 40,000 to 3,000 kw. To meet the load three turbo-generators are installed. The capacity of two generators is 15,000 kw each and the 3rd is rated at 6,000 kW. Determine the following: a) Load factor b) Capacity factor c) Maximum demand
Hoover Dam has a nameplate capacity of 2080 MW[] and an annual generation averaging 4.2 TW·h. (The annual generation has varied between a high of 10.348 TW·h in 1984, and a low of 2.648 TW·h in 1956.) Determine the capacity factor. Ans. 23% (Show the Solutions)
Q2) A generating station has a maximum demand of 30 MW, a load factor of 0.6 and plant use factor of 0.8. Determine i) The daily energy produced ii) The reserve capacity of the plant iii) The maximum energy that could be produced if the plant were running all the time iv) The maximum energy that could be produced daily, if the plant when running according to operating schedule were fully loaded
a) Explain briefly how electricity can be sold to a grid by use solar energy. b) Wind farm consist of ten wind turbines with nominal capacity of 2MWper turbine, has a total of 20 MW for farm as a whole, in year 2020, the farm produced a total energy 43416MWH, find a capacity factor.
b) A1000 MW turbine generated 648 MWh during 30 day. What would is capacity factor be?
The voltage v(t)=359.3cos(t)volts is applied to a load consisting of a 10 resistor in parallel with a capacitive reactance XC=25. Calculate (a) the instantaneous power absorbed by the resistor, (b) the instantaneous power absorbed by the capacitor. (c) the real power absorbed by the resistor, (d) the reactive power delivered by the capacitor, and (e) the load power factor.
7. A power station has to meet the following load demand: Load A 50 kW between 10 A.M. and6 P.M. Load B 30 kW between 6 P.M. and 10 P.M. Load C 20 kW between 4 P.M. and 10 A.M. Plot the daily load curve and determine (i) diversity factor (ii) units generated per day (iii) load factor. () 1-43 (ii) 880 kWh (iii) 52-38%]