shown in the below figure. The reserve capacityin the plant at 70% capacity factor isbneMW49050puig7.2lust% Time100500 0(а) zero(b) 10 MW(d) 50 MW(c) 30 MW

we need to determine reserve capacity.

Answered: a in the plant at 70% capacity factor…

Engineering

Electrical Engineering

a in the plant at 70% capacity factor is bris MWA 90 SET 50 % Time 100 500 00 (b) 10 MW (d) 50 MW (а) zero (c) 30 МW

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.31P: Consider two interconnected voltage sources connected by a line of impedance Z=jX, as shown in...

See similar textbooks

Related questions

Q: A charge of 350 VA with a power factov of 0,70 leading, connected to q source of 50 Hz and vottage…

A: The complex power in an AC system is defined as the product of rms value of applied voltage and…

Q: 93uF 7 L 301 3302 5 Pa ssband ain190 vj İVJ I got the exact ftsl98.0549Hz- vil is the Voltage gan…

A: Write the expression to find exact value of lower cutoff frequency for the given circuit as follows:

Q: If a Load absorbs 10 kVA at a leading power factor of 0.6. Then the complex power is: Select one: a.…

A: Load absorbed S= 10kVA Power factor= 0.6 leading Find the power in complex form

Q: a) Determine the maximum current. b) Determine the voltage across each components. c) Determine the…

Q: ii) the percentage of overshoot and the settling time using values from b(j). R(s) s+2 C(s) s(s+3) 1…

A: Given Dominant pole : Pole which is near to origin is taken as dominant pole of the given system

Q: In wind turbine, rotor is locked below 16Km/h wind speed. Select one: True False

A: Wind turbine: A wind turbine is a rotational device that converts the wind's kinetic energy into…

Q: state if v(ES = 2sin Lt. %3D n the steady method. Ose any 2224 H 1F= 215 Na

Q: Find the percent overshoot, settling time, rise time, and peak time for 14.145 T (s):…

A: calculation of percentage overshoot, settling time, rise time, and peak time for the given transfer…

Q: 2. Solve for the branch currents using any method. 10V 15V 20 50 30 20V 100

Q: Q5) Explain why the following equations is equal to zero: 1) V•B30

A: As per the honour code I will only do the first question. Kindly repost the other question again.…

Q: Betz efficiency applies to O a. wind turbines O b. solar cells O c. parabolic dish O d. heat engines

A: The Betz limit is a theoretical maximum limit on the power production from a wind turbine. Betz's…

Q: Vdc across the load is 110 V rms/ 1.0k 12.36V 24.73V 110V 55V

A: In this question, We need to choose the correct options What is average DC voltage?

Q: The reactance of a generator is given as 0.25 pu based on the generator of 13 KV, 200 MVA. Determine…

A: Given, Reactance, Xg(old)= 0.25 pu Voltage, kV(old)= 13 kV Apparent power, MVA (old)= 200 MVA Base…

Q: A power station consists of two synchronous generators A & B of ratings 250 MVA and 500MVA with…

A: Given a power station consists of two synchronous generators A & B, Synchronous generator A…

Q: fa 5ettZ/u_4404/ nine slot Pek Phase Yoo tubastehase -300 KVA Cait Pitch 2slot Toad frind Als Luheh…

A: “Since you have posted a question with multiple sub-parts, we will solve the first three sub-parts…

Q: If the number of combinations to find unit commitment is 225 for two hours. Find the number of…

A: Unit commitment: It is a process of the decide when and which the generating units at a…

Q: The perunit value of acceleration power of 200 MVA generator is 0.15. What will be the actual…

A: as per our guidelines we are supposed to answer only one question. Kindly repost other questions as…

Q: i(t) (0360 mH i(),3240 mH

A: The given circuit diagram is shown below:

Q: ele 50 -j102 292 ww- ww 60/120° V j202 -20+87.7j None of the answers -89.5+59.1j

Q: The answers are in rectangle form

Q: X(s) Y(s) (s+2)

Q: The variation of the load is considered over a period of month in the monthly load curve.…

A: True The monthly load curve can be obtained from the daily load curves of that month. average values…

Q: FOR A Two TeRMIWAL DEVICE THE TOPGRAPIH SHOWN BELOw SiHows THe CORRENT TAROUCH TAG DEVICE Vs TimE 8…

Q: 15. Determine the nodal voltages for the networks ce" E = 50 V / 120° 10 Ω Μ -10 Ω 8 Ω moo 4 Ω ΖΩ Οι…

Q: A 1200 KW,60 Hz synchronous alternator A is in parallel with a 400 kW,60 Hz alternator B.Both…

A: The load supplied by the alternator A is three-fourth of the 1000 kW bus, the load supplied is,…

Q: For Figure 4 below, Van = 120 Vz0°. Compute the readings of each meter, then sum to determine total…

Q: S 25+3 XC+)

Q: An A.C. voltage represented by e= 170 Sin(377t) volts is applied to a resistor resulting in a…

Q: e. The rms value of the load current equals to O 3.715 A O 2.256 A O 5.656 A 4.015 A

A: Rms value of load current equal to ?

Q: 132 I2 1052 В Is (+ lov A 15S C 25A 2052

Q: What is the value of the equivalent admittance? 100 ww sa -20 j10 a

Q: tors with fiux per pole is 21 mwbD and the e m.f generated is 63 V, then the speed of the machine is…

Q: pop system, v 6.65

A: The control system is of two types, the one-loop control system or the close loop control system.…

Q: j100Ω -j500 ... ll 12 A (10+je)V 2000 (5-j5)V (2)

A: To determine the currents i1 and i2

Q: Question 3 To reduce the power consumption, the capacitors should be located Complete Marked out of…

A: Answer 3: Locating capacitor as close as possible to the Load end will help to reduce losses within…

Q: P A 500 V de generator supplies a load 800 A at point A through 0.025 2 distributor and a load of…

A: As per our guidelines , we are supposed to answer only one question at a time. Please repost the…

Q: Lift force is the basic driving force in a multi blade vertical axis wind turbine. Select one: O…

A: The ease of the arrangement and improvement of vertical turn contraptions allowed to join a power…

Q: (1)= 0.4 p.u. V₁ = 1.040⁰ #12 = 0.12 + j0.16 100 MW + 50 Mvar

A: Ans :(d) 0.8 p.u

Q: The concentration ratio of parabolic trough power plant is typically O a. from 30 to 40 O b. more…

A: Parabolic trough concentrator: It is a set of concave mirrors that concentrate solar rays on the…

Q: j 502 j 152 if 150 LOʻv(E1 100 Lov E2 E3 200Lo°v 1002 502 15052.

Q: Choose the voltage level reduced by Grid sub-station O a. 11 KV O b. 220KV O c. 33 KV O d. 66 KV

A: Choose the correct option What is voltage level reduced by grid sub station.

Q: Problem 3: Find the economic dispatch for each of the load demand values PD = 100 MW, 300 MW, 500…

A: In this question, Increment cost function is given. Constraints of the each Generation system is…

Q: QUESTION 4 A 200mH inductor, a 820 ohm resistor, and a function generator are all connected in…

Q: 15. R=10 ohms, L=0.056 Henry and C=50 microfarad are connected in series in a 20O V, 60 cycle…

A: The solution is given below.

Q: 23. Acurrent of i= 6+ 10sin(100rt) + 20 sin(200n) is llowing through a series combination of a PMMC…

A: we need to find out ratio of MI and PMMC meter.

Q: If a Load absorbs 10 kVA at a leading power factor of 0.6. Then the complex power is: Select one: O…

A: Apparent power/Complex power, S=VI VAActive power/Real power, P=VI×Cosϕ KWReactive power, Q=VI×Sinϕ…

Q: Simplify Z=AB'C+B(A+C') using Karnaught table.

A: In this answer we will try to simplify the given Boolean expression using the K-map as shown below

Q: A 450nF capacitor, a 820 ohm resistor, and a function generator are all connected in parallel. The…

Concept explainers

Magnetic Moment

The magnetic moment is defined as the alignment of a magnet and its strength when the magnet is creating a magnetic field. There are number of examples of the magnetic moment, few are a current carrying conductor in the form of coil, elements at microscopic levels like electrons and many more.

Question

shown in the below figure. The reserve capacity
in the plant at 70% capacity factor is
bne
MW4
90
50
puig
7.2
lust
% Time
100
500 0
(а) zero
(b) 10 MW
(d) 50 MW
(c) 30 MW

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Unit commitment if the spinnind reserve not there in the power system what will happen?
What effects are produced by change in voltage? 1. Iron los..........varies approximately as V². 2. Cu loss..........it also varies as V² but decreases with an increase in voltage if constant kVA output is assumed. 3. Efficiency...........for distribution transformers, efficiency at fractional loads decreases with in- crease in voltage while at full load or overload it increases with increase in voltage and vice- versa. 4. Regulation..........it varies as but decreases with increase in voltage if constant kVA output is assumed. 5. Heating.........for constant kVA output, iron temperatures increase whereas Cu temperatures decrease with increase in voltages and vice-versa.
A Single Area consists of 3 generating units (G1/G2/G3) with the following characteristics: G1: 250 MVA rating, R1 = 0.02 pu (on the 250 MVA base), initial output P1 = 200 MW. G2: 350 MVA rating, R2 = 0.015 pu (on the 350 MVA base), initial output P2 = 300 MW. 0.03 pu (on the 300 MVA base), initial output P3 = 150 MW. G3: 300 MVA rating, R3 = The frequency of the system is 60 Hz. Assuming D = 1 pu on a common base of 1000 MVA, what is the new generation output for G3 for a load increase of 75 MW? Select one: O a. 190.55 MW O b. None of these O c. 203.38 MW d. 166.01 MW
Draw the circuit diagram of Two quadrant chopper which is having average load voltage might be positive or negative. Explain each quadrant operation with neat sketch. I want more than 350 words and I do not want it in handwriting
A 500 MVA synchronous machine has H, = 5.6 MJ/MVA and a 1200 MVA machine has H₂ = 2.0 MJ/MVA. The two machines operate in parallel in a power station. What is the equivalent. H constant for the two, relative to a 100 MVA base?
7. TY Hat CHICL Ans. 1. Iron los.........varies approximately as V². 2. Cu loss..........it also varies as ² but decreases with an increase in voltage if constant kVA output is assumed. 3. Efficiency...........for distribution transformers, efficiency at fractional loads decreases with in- crease in voltage while at full load or overload it increases with increase in voltage and vice- versa. 4. Regulation..........it varies as but decreases with increase in voltage if constant kVA output is assumed. 5. Heating.........for constant kVA output, iron temperatures increase whereas Cu temperatures decrease with increase in voltages and vice-versa. quems
The indication of a lagged demand meter approaches the value of the actual load at a rate which is proportional to A. Quotient of the load and the meter indication. B. product of the load and the meter indication C. Difference between the load and the meter indication D. sum of the load and the meter indication
I just got confused with the unit. Why is it mW? And not just W? Or maybe this solution is wrong? I based it off a youtube video. Please, I need clarification as whether the unit is just "W" or "mW".
What is the purpose of power factor correction to a given load? O To reduce the amount of voltage to the load. O To reduce the amount of dependence on automated machinery. O To reduce the amount of current to the load. O To reduce the amount of resistance of the load.
State Kirchhoff’s Current Law.
reactance of G3 in per unit on a base of 100 MVA, 35 KV is Ο Ο Ο Ο Three generators rated as follows: G1: 100 MVA, 33 KV, sub-transient reactance of 10%; G2: 150 MVA, 32 KV, sub-transient reactance of 8% and G3: 110 MVA, 30 KV, sub transient reactance of 12%. O O O 10% 18% 8% 12% 9% 7% 14% reactance of G2 in per unit on a base of 50 MVA, 35 KV is 16% 1.88% 2.12% 2.23% 1.93 % 2% 1.75% 2.64% 2.25%
Hoover Dam has a nameplate capacity of 2080 MW[] and an annual generation averaging 4.2 TW·h. (The annual generation has varied between a high of 10.348 TW·h in 1984, and a low of 2.648 TW·h in 1956.) Determine the capacity factor. Ans. 23% (Show the Solutions)