Consider a flask, as shown in Figure Q1. The flask wall is designed with an air layer sealedbetween the inner container and the outer case. The inner container has a diameter of 8.5 cm,and the case has a diameter of 9.5 cm. The flask is 17 cm tall and the outer case is made of avery thin steel material. The cap and base of the flask are well insulated.a) During a steady-state condition, the ambient air temperature is 20°C with theconvection heat transfer coefficient, ho of 4 W/m².K. Consider a uniform watertemperature Twater of 95 °C with the inner container surface at the same temperature asthe water temperature at any time. If the convection and the radiation heat transfer to benegligible within the air layer, obtain the temperature variation in the flask wall byusing the heat conduction equation.b) Determine the outer case temperature (°C) and the rate of heat loss (kW) from the flask.c) If the air layer of the flask is replaced with a vacuum layer, will the rate of heat losschange? Explain.Flask wallwaterAir layerFigure Q1A large plane wall is subjected to specified heat flux and temperature on the left surface and no conditions on the rightsurface. The mathematical formulation, the variation of temperature in the plate, and the right surface temperature are to bedetermined for steady one-dimensional heat transfer.k=2.5 W/m-°C.q=700 W/m²T;=80°CL=0.3 m

The heat flux through a plane wall in one-dimensional steady heat conditions can be calculated using…

A large plane wall is subjected to specified heat flux and temperature on the left surface and no conditions on the right surface. The mathematical formulation, the variation of temperature in the plate, and the right surface temperature are to be determined for steady one-dimensional heat transfer. k=2.5 W/m-°C. k =700 W/m? Tj=80°C L=0.3 m

A large plane wall is subjected to specified heat flux and temperature on the left surface and no conditions on the right surface. The mathematical formulation, the variation of temperature in the plate, and the right surface temperature are to be determined for steady one-dimensional heat transfer. k=2.5 W/m-°C. k =700 W/m? Tj=80°C L=0.3 m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Consider an experimental structure required to always have constant pressure. For this purpose, a collapsible compartment has been installed that expands and contracts to adjust the volume of air inside the structure for maintaining constant air pressure of 1 atm. Given the total volume of air inside the structure was 100,000 m' when the compartment was fully collapsed, solve the following: If a constant pressure is to be maintained while the temperature varies from 0°F to 150°F, find the volume of air that the compartment holds when it expands to the maximum. For the temperature transition mentioned above, find the change in internal energy undergone by the air in the structure. Also, find the work done by the compartment while it expands. Assume air to be an ideal gas.
In a concentrated solar power plant, molten salt tank is used to store the thermal energy from the sun during the day. The tank wall thickness is 3cm containing molten salt at a temperature of 390 degree Celsius. There is atmospheric air outside the tank at a temperature of 30 degree Celsius. Suppose heat is lost as a result of heat transfer from the molten salt to the atmospheric air. What is the mode of heat transfer in this condition? conduction then convection convection then conduction convection then conduction then convection conduction then convection then conduction
3.4 Estimate the rate of heat loss due to radiation from a covered pot of water at 95 ° C. How does this compare with the 60 W that is lost due only to convection and conduction losses? What amount of energy input would be needed to maintain the water at its boiling point for 30 minutes? The polished stainless steel pot is cylindrical, 20 cm in diameter and 14 cm high, with a tight-fitting flat cover. The air temperature in the kitchen is about 25 ° C. State any assumptions you make in deriving your estimates
1. ( 3-units. If the surrounding is held T = 0 and the base is held at T = 100r² sin30. Find the temperature distribution inside the cylinder. A smi-infinite cylinder in a steady state with the environment of radius
A pressure cooker cooks a lot faster than an ordinary pan by maintaining a higher pressure and temperature inside. The lid of a pressure cooker is well sealed, and steam can escape only through an opening in the middle of the lid. The pressure relief valve consists of a spring-loaded disk that is positioned over this opening. Consider that a certain portion of a pressure cooker is initially filled with water and put on top of a stove (State - 1). Heat is added just until the pressure relief valve opens (State 2). Heat continues to be added until all of the liquid disappears (State 3). Using the knowledge that you learned in the Thermodynamics-I Course, analyze the operation of this pressure cooker thermodynamically (i.e. find the intensive properties of water such as temperature, pressure and quality, mass of liquid water in the cooker, mass of water vapor that has passed through the pressure relief valve, and time passed for various stages of its operation). Operation and design…
A pressure cooker cooks a lot faster than an ordinary pan by maintaining a higher pressure and temperature inside. The lid of a pressure cooker is well sealed, and steam can escape only through an opening in the middle of the lid. The pressure relief valve consists of a spring-loaded disk that is positioned over this opening.Consider that a certain portion of a pressure cooker is initially filled with water and put on top of a stove (State - 1). Heat is added just until the pressure relief valve opens (State 2). Heat continues to be added until all of the liquid disappears (State 3).Using the knowledge that you learned in the Thermodynamics-I Course, analyze the operation of this pressure cooker thermodynamically (i.e. find the intensive properties of water such as temperature, pressure and quality, mass of liquid water in the cooker, mass of water vapor that has passed through the pressure relief valve, and time passed for various stages of its operation). Operation and design…
Q2:- A sphere made of pure copper, which is 13 mm in diameter, is 70 °C (at t=0) when it inserted into a gas having a temperature of 25 °C. After 65 s the temperature of the sphere reach 60 °C. Make the appropriate assumption to find the heat transfer coefficient of the gas. What is the temperature of the sphere after 80 s. (A;=TT D2, V= TT D³/6, Lc=V/ A,)
A pressure cooker cooks a lot faster than an ordinary pan by maintaining a higher pressure and temperature inside. The lid of a pressure cooker is well sealed, and steam can escape only through an opening in the middle of the lid. The pressure relief valve consists of a spring-loaded disk that is positioned over this opening. Consider that a certain portion of a pressure cooker is initially filled with water and put on top of a stove (State - 1). Heat is added just until the pressure relief valve opens (State 2). Heat continues to be added until all of the liquid disappears (State 3).
How long should it take to boil an egg? Model the egg as a sphere with radius of 2.3 cm that has properties similar to water with a density of = 1000 kg/m3 and thermal conductivity of k = 0.606 Watts/(mC) and specific heat of c = 4182 J/(kg C). Suppose that an egg is fully cooked when the temperature at the center reaches 70 C. Initially the egg is taken out of the fridge at 4 C and placed in the boiling water at 100 C. Since the egg shell is very thin assume that it quickly reaches a temperature of 100 C. The protein in the egg effectively immobilizes the water so the heat conduction is purely conduction (no convection). Plot the temperature of the egg over time and use the data tooltip in MATLAB to make your conclusion on the time it takes to cook the egg in minutes.
Sipho’s mother is making a fire in the stove inside a shack using coal. A fan is used to extract the flue gasfrom the fire via a chimney made of zinc material. The wall thickness of Chimney is L=4mm and the walltemperature of the chimney on the flue gas side is T_si=60˚C. Sipho, playing outside next to the chimneyexperiences an ambient temperature of 20˚C. The surrounding temperature is T_sur=35˚C and the emissivityis ε=0.95. Assume the convection coefficient is 20W/m2K and the chimney is grey material.Under these conditions determine the outer surface (air side) temperature T_so=? of the chimney.
Q1) A steel cylinder 10 cm in diameter and 10 cm long is initially at 300 °C. It is suddenly immersed in an oil bath that is maintained at 40 °C, with h =280 W/m² °C. Find: (a) The temperature at the center of the solid after 2 min, and (b) The temperature at the center of one of the regular faces after 2 min.
Q4/ A room on the second floor of a house with a balcony has a door. The door made of teak (wood) and it contains a large sheet of glass (outside winter type) in the middle and constitutes 80% of the area of the door. Door thickness is 40 mm and the temperature in the room 25. °C when the temperature is in the balcony 8 °C. Calculate the rate of heat loss from the room to the balcony through the door. The door dimensions 2m x 1m. Assume Inside and outside still air thermal resistance f= 8.29 W/m2 °C and f. 34.1 W/m2 °C respectively