A lawn-sprinkling system is controlled automatically by certain combinations of the following variables. Season (S = 1, if summer; 0, otherwise) Moisture content of soil (M = 1, if high; 0, if low) Outside temperature (T = 1, if high; 0, if low) Outside humidity (H = 1, if high; 0, if low) The sprinkler is turned on under any of the following circumstances. 1. The moisture content is low in winter. 2. The temperature is high and the moisture content is low in summer. 3. The temperature is high and the humidity is high in summer. 4. The temperature is low and the moisture content is low in summer. 5. The temperature is high and the humidity is low. Use a K-map to find the simplest possible logic expression involving the variables S, M, T and H for turning on the sprinkler system.

A lawn-sprinkling system is controlled automatically by certain combinations of the following variables. Season (S = 1, if summer; 0, otherwise) Moisture content of soil (M = 1, if high; 0, if low) Outside temperature (T = 1, if high; 0, if low) Outside humidity (H = 1, if high; 0, if low) The sprinkler is turned on under any of the following circumstances. 1. The moisture content is low in winter. 2. The temperature is high and the moisture content is low in summer. 3. The temperature is high and the humidity is high in summer. 4. The temperature is low and the moisture content is low in summer. 5. The temperature is high and the humidity is low. Use a K-map to find the simplest possible logic expression involving the variables S, M, T and H for turning on the sprinkler system.

C++ for Engineers and Scientists

4th Edition

ISBN:9781133187844

Author:Bronson, Gary J.

Publisher:Bronson, Gary J.

Chapter3: Assignment, Formatting, And Interactive Input

Section: Chapter Questions

Problem 6PP: (Heat transfer) The formula developed in Exercise 5 can be used to determine the cooling time, t,...

See similar textbooks

Similar questions

(Civil eng.) The maximum load that can be placed at the end of a symmetrical wooden beam, such as the rectangular beam shown in Figure 2.20, can be calculated as the following: L=S1dc L is the maximum weight in lbs of the load placed on the beam. S is the stress in lbs/in2. I is the beam’s rectangular moment of inertia in units of in4. d is the distance in inches that the load is placed from the fixed end of the beam (the “moment arm”). c is one-half the height in inches of the symmetrical beam. For a 2” × 4” wooden beam, the rectangular moment of inertia is given by this formula: I=baseheight3=12=24312=10.674 c=(4in)=2in a. Using this information, design, write, compile, and run a C++ program that computes the maximum load in lbs that can be placed at the end of an 8-foot 24 wooden beam so that the stress on the fixed end is 3000lb/in2. b. Use the program developed in Exercise 9a to determine the maximum load in lbs that can be placed at the end of a 3” × 6” wooden beam so that the stress on the fixed end is 3000lb/in2.
(Automotive) a. An automobile engine’s performance can be determined by monitoring its rotations per minute (rpm). Determine the conversion factors that can be used to convert rpm to frequency in hertz (Hz), given that 1rotation=1cycle,1minute=60seconds,and1Hz=1cycle/sec. b. Using the conversion factors you determined in Exercise 7a, convert 2000 rpm into hertz.
Mixture Problems My Sol A 1500 gallon tank initially contains 600 gallons of water with 5 lbs of salt dissolved in it. Water enters the tank at a rate of 9 gal/hr and the water entering the tank has a salt concentration of (1 + cos(t)) lbs/gal. If a well mixed solution leaves the tank at a rate of 6 gal/hr, how much salt is in the tank when it overflows? Solve the equation via MATLAB making sure that you passed though the following: 1. Initialization of variables 2. Setting up the Volume Equation 3. Settimg Up the differential equation 4. Listing down initial Conditions 5. Plugging in Conditions. 6. Finding the resulting model 7. Finding the concentration when the tank overflows 8. Graph the solutions
Noted: I want to this answer in just simple C language program.THANK YOU An iron rod is graded based on the following criteria: (i) magnetite must be greater than 50 (ii) calcium carbonate content must be less than 0.7 (iii) other adulterants must be greater than 5600 The grades are as follows: Grade is A if all three conditions are met Grade is B if conditions (i) and (ii) are met Grade is C if conditions (ii) and (iii) are met Grade is D if conditions (i) and (iii) are met Grade is E if only one condition is met Grade is F if none of the conditions are met Write a program, which will require the user to give values of magnetite, calcium carbonate and other adulterants under consideration and output the grade of the iron.
Q3i design a program for estimate the type of fluid flow depending on Reynold mumber (Re). The type of flow can be estimated from the table below and (Re) can be cakculated from the following equation. Re- Pud Where: pis the density u is velocity d is pipe diameter u is viscosity Re no. Fluid flow type E 2300 Laminar 2300 Re-4000 Transition 24000 Turbulent
A motor runs when the start button is pressed and the following conditions are satisfied .Safety door is closed The level of the liquid in the tank is above a .certain level The motor stops and a lamp is to glow if any of the following conditions occur .The stop button is pressed 风 .The safety door is opened .The liquid level is below the satisfactory level The lamp stops glowing when the motor starts. One signal triggers an alarm bell and another one causes a flash-lamp to start flashing (on/off) when a fault occurs in the motor. The bell stops when the operator acknowledges the alarm, but the lamp continues to flash until the fault is .removed The designer needs for....... conditional output boxes for drawing the ASM-chart for the controller of the .aforementioned system 0 2 5 3 6 70
(Mechanical eng.) The minimum radius required for a cylindrical rod, such as one supporting a bicycle pedal (see Figure 2.22), to provide enough support for the pressure exerted by the rider’s foot yet not exceed the stress placed on the crank arm’s sprocket attachment, is given by this formula: r3=dPS r is the radius of the cylindrical rod in inches. d is the length of the crank arm in inches. P is the weight placed on the pedal in lbs. S is the stress in lbs/in2. Using this information, design, write, compile, and run a C++ program that computes the value of r for a crank arm that’s 7 inches long, accommodates a maximum weight of 300 lbs, and is able to sustain a stress of 10,000 lbs/in2.
(Heat transfer) The formula developed in Exercise 5 can be used to determine the cooling time, t, caused only by radiation, of each planet in the solar system. For convenience, this formula is repeated here (see Exercise 5 for a definition of each symbol): t=Nk2eAT3fin A=surfaceareaofasphere=4r2 N=numberofatoms=volumeofthespherevolumeofanatom Volume of a sphere sphere=43radius3 The volume of a single atom is approximately 11029m3 . Using this information and the current temperatures and radii listed in the following chart, determine the time it took each planet to cool to its current temperature, caused only by radiation.
(Practice) You’re given the task of wiring and installing lights in your attic. Determine a set of subtasks to accomplish this task. (Hint: The first subtask is determining the placement of light fixtures.)
2- The short circuit is defined as resistance, then the current is . .Amper.
Noise margin is the amount of O a. both signal and noise voltage that a logic gate can tolerate O b. noise voltage that a logic gate can tolerate Ос. None of the choices are correct O d. signal voltage that a logic gate can tolerate
Design logic circuits that controls an elevator door in a 3 story building. The circuit has a for input lines. M is a logic circuit that indicates when the elevator is moving (M = 1) or stopped (M = 0). F1, F2, F3 are floor indicator signals that are normally low, and they go hi only when the elevator is positioned at the level of the particular floor. For example, when the elevator is lineup level with the second floor F2=1 and F1 = F3 = 0 the circuit output is the OPEN signal which is normally Low and it is to go HIGH when the elevator door is to be opened