A line is recorded as 472.90m long using a 30m tape. During measurement, the temperature is 32°C and the tape is laid on the ground under a 75N pull. The tape has the following properties: weight of 0.065kg/m, young modulus of elasticity is 200GPA, cross sectional area of the tape is 3mm? and the coefficient of linear expansion is 0.0000116/"C. The tape is 30.005m long at 40°C under a 20ON pull supported at both ends. Assume the standard pull is 50N, compute: a. The standard temperature in °C. b. The actual length of tape during measurement in meter. c. The true distance of the line in meter. If the survey are to be connected to the national mapping system of a country, the distances will need to be reduced to the common datum of the system, namely MSL (Mean Sea Level). The adjustment is expressed as H Reduction Factor = 1 R L' = L(1 d. If the height of measurement from the Mean Sea Level is 12km, determine the adjusted distance in meter.

A line is recorded as 472.90m long using a 30m tape. During measurement, the temperature is 32°C and the tape is laid on the ground under a 75N pull. The tape has the following properties: weight of 0.065kg/m, young modulus of elasticity is 200GPA, cross sectional area of the tape is 3mm? and the coefficient of linear expansion is 0.0000116/"C. The tape is 30.005m long at 40°C under a 20ON pull supported at both ends. Assume the standard pull is 50N, compute: a. The standard temperature in °C. b. The actual length of tape during measurement in meter. c. The true distance of the line in meter. If the survey are to be connected to the national mapping system of a country, the distances will need to be reduced to the common datum of the system, namely MSL (Mean Sea Level). The adjustment is expressed as H Reduction Factor = 1 R L' = L(1 d. If the height of measurement from the Mean Sea Level is 12km, determine the adjusted distance in meter.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.5P: The results of a tensile test are shown in Table 1.5.2. The test was performed on a metal specimen...

See similar textbooks

Similar questions

The results of a tensile test are shown in Table 1.5.2. The test was performed on a metal specimen with a circular cross section. The diameter was 3 8 inch and the gage length (The length over which the elongation is measured) was 2 inches. a. Use the data in Table 1.5.2 to produce a table of stress and strain values. b. Plot the stress-strain data and draw a best-fit curve. c. Compute the, modulus of elasticity from the initial slope of the curve. d. Estimate the yield stress.
Engr. Sova Ho used 30m length of tape in measuring a distance line. The measured length of the line was recorded to be 454.62 m. During the measurement the temperature reading was 11 oC and the tape was supported at both ends. The cross sectional area of the tape is 6.50mm2 and the modulus of elasticity is 200 GPa. The tape has a weight of 0.075 kg/m. K= 11.6 x10-6 m/c. If the engineer determined the Temperature correction, Pull correction, and Sag Correction lengths to be 1,640.01 μm, 588μm, and 1.71 mm respectively, per segment. Calculate the applied Pull of the 30m tape in kg.
ngr. Beleric measured a distance line using a 20m length of stainless steel tape measure. The line's length was determined to be 396.84meters.The temperature was 10 oC during the measurement, and the tape was supported on both ends.The tape has a cross sectional area of 7.20mm2 and a modulus of elasticity of 200GPa. The tape is 0.095 kg/m in weight. k = 11.6 x10-6 m/C If the engineer determined the lengths of the Temperature correction, Pull correction, and Sag Correction to be 1,197.23μm, 285.53 μm, and 2.23 mm, per segment, Calculate the 20m tape's standard pull in kilograms.
carculate the Youngs modulus for the material of the bar shown below, The bar has an initial length of 400 mm and is measured to extend by 0.22 mm under a tensile load of 75KN, When the force is released the bar returns to its original length. The bar has the rectangular cross-section shown below. (17p) 20 mm 75 kN 75 kN 25 mum 400 mm
Calculate 6 Calculate the tensile stress when applied force of 120OON on specimen of * diameter of 7mm 111 O 211 O 311 O 411 O
Question 8 The rigid, horizontal slab is attached to two identical copper rods. There is a gap A = 0.18 mm between the middle bar, which is made of aluminum, and the slab. Neglecting the mass of the slab, calculate the stress in each rod when the temperature in the assembly is increased by 85 °C. Use the following data: A (mm?) a (C) E (GPa) Each copper rod 500 16.8 x 10-6 120 Aluminum rod 400 23.1 x 10- 70 Copper unusunjv Copper 750 mm-
An aluminum pipe (modulus of elasticity 10.1x10^6 psi) is fixed at one end and is subjected to a tensile load of 127.5 kips at the free end. The length and cross-sectional area of the pipe is given as 36.1 in and 9.11 in^2. Assume that the aluminum pipe has clockwise torques (100 lb-in) acting at the midpoint and free end of the pipe. (a) Derive the element stiffness matrix
The shown circular bar is fixed to the left wall. It has a diameter of 0.5 in and length of 60 in at 50 °F when it is unloaded. There is a gap of 0.08 inches between the bar end and the right opposite wall. The bar was simultaneously loaded axially with a load P and heated such that the temperature was raised from 50 °F to 130 °F along all the bars. The bar material has a modulus of elasticity = 15 x 10° psi and coefficient of thermal expansion = 10.6x106 1/°F. Determine the maximum magnitude of the load P such that the right opposite wall remains stress free.
the solid circular shaft rod has an original diameter of 20mm. when the load of 50kN is applied the shaft stretches 1.4mm and it has a Poisson's ratio of 0.25. Calculate the change in diameter of the shaft?Assume shaft is in the elastic region.
The failure stress of a homogeneous steel bar having a diameter of 10 mm is 250 MPa. Using a factor of safety of 2.0 and if the elastic mođulus and length of the bar is 200 GPa and 2 m respectively, calculate the elongation in mm of the bar corresponding to the maximum load it can support. (А) 5 (в) 2.5 1.25 D) 0.625
A compound bar consisting of bronze, aluminum, and steel segments is loaded axially as shown in the figure. Determine the maximum allowable value of P if the change in length of the bar is limited to 2 mm and the working stresses prescribed in the table are not to be exceeded. Material Properties Material Area(mm2) E (GPa) Normal Stress(MPa) Bronze 450 83 120 Aluminum 600 70 80 Steel 300 200 140 Aluminum 3P Bronze Steel 2P 4P - 0.6 m →- 1.0 m 0.8 m
NOTE: The standard pull of the tape is 5kg while the team pulled only at 4kg The field temperature is 300 while the standard temp of the tape is 200 The cross sectional area of the tape is 0.05cm2. The coefficient of linear expansion is 0.000011610C and the modulus of elasticity of steel is given to be 2.0 x 106 kg/cm. The tape used here is a 50m steel tape. Determine the actual length of each lines