A local toy manufacturer is using a production line that runs 8 hours per day and produces a toy that requires a total to be performed. The daily demand is 90 toys. Times of the tasks are 2.73, 2.01, 2.13, 2.0, 2.61, 2.71, and 2.95 minute C, D, E, F, and G, respectively. However, due to the nature of the product there are precedence rules that must be obs Such that Task A does not need any predecessors; task B requires task A to be completed. To start task C and task D, require task B to be completed. Task C must be completed prior to stating task E. Task F needs both task Dand task E completed. Finally, task G can start only once task F is completed.What should be the calculated cycle time in minutes O a. None is correct O b. 4.80 5.33
Q: An assembly plant for the Blood Pressure RX, a portable blood pressure device, has 400 minutes…
A: Given - Task Performance Time (minutes) Task Must Follow Task Listed Below A 4 -…
Q: The City Commission of Nashville has decided to build a botanical garden and picnic area in the…
A: Gantt chart is a visual representation of a network diagram which helps to identify the starting and…
Q: A local toy manufacturer is using a production line that runs 8 hours per day and produces a toy…
A:
Q: A local toy manufacturer is using a production line that runs 8 hours per day and produces a toy…
A: Given- Available time per day = 8 hours × 60 minutes = 480…
Q: A local toy manufacturer is using a production line that runs 8 hours per day and produces a toy…
A: Given Data: Task Time taken A 2.73 B 2.01 C 2.13 D 2.0 E 2.61…
Q: Develop a solution for the following line balancing problem, allowing a cycle time of 5 minutes. a.…
A: Note: - Since we can answer only up to three subparts we will answer the first three subparts(a, b,…
Q: Illinois Furniture, Inc., produces all types of office furniture. The "Executive Secretary" is a…
A: Total duration during the day = 480 mins The average daily demand of chairs = 50 Desired output =…
Q: A local toy manufacturer is using a production line that runs 8 hours per day and produces a toy…
A: Given that: Task Duration (in mins) A 2.73 B 2.01 C 2.13 D 2 E 2.61 F 2.71 G 2.95
Q: The Action Toy Company has decided to manufacture a new train set, the production of which is broken…
A: Given- Available time over 40 hours work week = 40 hours×3600 seconds per hour…
Q: A local toy manufacturer is using a production line that runs 8 hours per day and produces a toy…
A: Required cycle time = Available time / No. of units to produce =…
Q: Using the information presented in the following table, identify the processing sequence that…
A:
Q: A local toy manufacturer is using a production line that runs 8 hours per day and produces a toy…
A: Given Data: Task Time taken A 2.73 B 2.01 C 2.13 D 2.0 E 2.61…
Q: A new surgical facility called Cut & Sew has opened in the United States. The branches of the…
A:
Q: evelop a solution for the following line balancing problem, allowing a cycle time of 5 minutes.…
A: The Precedence Diagram given below: A D F B C…
Q: A shoe assembly plant buys leather tops and soles from its suppliers. The leather tops have no color…
A: a) With B = 40, S = 30 mins, t = 0.25 mins. It takes S + tB minutes to color B leather tops.…
Q: A dress-making operation is being designed as an assemblyline. Table 10-22 shows the tasks that need…
A: Note- As per the Bartleby guidelines only the first three parts have been answered. For obtaining…
Q: This exercise only contains parts b, c, d, e, and f. b) Given the demand, the cycle time for the…
A:
Q: Stanford Rosenberg Computing wants to establish an assembly line for producing a new product, the…
A: Given - Task Time (Sec) Immediate Predecessor A 11 − B 15 A C 7 A D 4 B, C E 20 D
Q: Given the following line balance data in the table below. For eight hours of operating time per day…
A: Line balancing is a creation system that includes balancing administrator and machine time to…
Q: The City Commission of Nashville has decided to build a botanical garden and picnic area in the…
A: Precedence table-
Q: Pane Grammar As part of a major plant renovation project, the industrial engineering department has…
A: Given data: *As per guideline 3 subparts are answerable, repost the remaining part
Q: Five jobs are ready for processing at time zero through a workstation. The details of the processing…
A: SPT- Shortest Processing Time SPT states the job or customer arriving at the work station has…
Q: WorkPro is a small manufacturer. It uses a job process for production. The following sample of jobs…
A: "Since you have asked multiple questions, we will solve the first one for you. To get remaining…
Q: The tasks shown in the following precedence diagram are to be assigned to workstations with…
A: a) Available time =440 minutes Desired output = 275 units Desired Cycle time= 1.6 minutes =…
Q: An assembly line with 17 tasks is to be balanced. The longest task is 2.4 minutes, and the totaltime…
A: Minimum cycle time = length of the longest task Therefore, the minimum cycle time = 2.4 minutes
Q: The desired daily output for an assembly line is 540 units. This assembly line will operate 720…
A: Line balancing is a process which allocate activity to right workstation based on different…
Q: A local toy manufacturer is using a production line that runs 8 hours per day and produces a toy…
A: This problem can be solved using: Cycle time = Available time / Desired output
Q: A local toy manufacturer is using a production line that runs 8 hours per day and produces a toy…
A: Given - A local toy manufacturer is using a production line that runs 8 hours per day and produces a…
Q: A local toy manufacturer is using a production line that runs 8 hours per day and produces a toy…
A: The answer is below:
Q: The theoretical minimum number of workstations is ??? Were you able to assign all the tasks to the…
A: Line balancing refers to a strategy of production involving the balancing of machine time and…
Q: You have been asked to balance a flow shop assembly operation to achieve an output rate of 80 units…
A: Given data is,
Q: Managers at the First Community Bank are attempting to shorten the time it takes customers with…
A: Bottlenecks are basically the obstacles which can lead to slowing down of the whole process. At the…
Q: Sue Helms Appliances wants to establish an assem-bly line to manufacture its new product, the Micro…
A: Given information Activity Duration Immediate predecessors A 10 B 12 A C 8 A, B D…
Q: A local toy manufacturer is using a production line that runs 8 hours per day and produces a toy…
A: Given Data: Task Time taken A 2.73 B 2.01 C 2.13 D 2.0 E 2.61…
Q: A manufacturer is designing a product layout for a new product production. It plans to use a…
A: Production time= 8*60= 480 minutes Demand= 110 units Cycle time= production time/ demand = 480/110 =…
Q: A manufacturer needs to produce 300 coffee pots per 8 hour day. The discrete tasks required to…
A:
Q: A local toy manufacturer is using a production line that runs 8 hours per day and produces a toy…
A: Working hour = 8 hours per day The total task to perform =7 task Daily demand= 100 toys Total Task…
Q: What is the cycle time and what is the minimum number of workstations required Construct the…
A: Cycle time indicating the required time for producing single unit of item. Line balancing is a…
Q: A local toy manufacturer is using a production line that runs 8 hours per day and produces a toy…
A:
Q: A visa application process from a Tumaritis country can be described in the chart below. The head of…
A: a. The difference between bottleneck and constraints are: Sl. No. Bottlenecks Constraints 1…
Q: A local toy manufacturer is using a production line that runs 8 hours per day and produces a toy…
A: Demand is the total quantity of goods and services for which the consumers are ready to pay…
Q: The table below shows the time for each work element in an manual assembly process, along with the…
A: Given that: Work element A B C D E F G H I J Time (minutes) 0.7 0.4 0.2 0.3 0.5 0.4 0.6 0.5 0.3…
Q: Alocal toy manufacturer is using a production line that runs 8 hours per day and produces a toy that…
A: This problem can be solved using: Minimum no. of station = Total task time / Cycle time Cycle time =…
Q: A local toy manufacturer is using a production line that runs 8 hours per day and produces a toy…
A: Given Data: Task Time taken A 2.73 B 2.01 C 2.13 D 2.0 E 2.61…
Q: A local toy manufacturer is using a production line that runs 8 hours per day and produces a toy…
A: Given Data: Task Time taken A 2.73 B 2.01 C 2.13 D 2.0 E 2.61…
Q: A local toy manufacturer is using a production line that runs 8 hours per day and produces a toy…
A: The answer is as follows:
Q: A local toy manufacturer is using a production line that runs 8 hours per day and produces a toy…
A: Demand is the total quantity of products and services for which the consumers are willing to pay…
Q: The desired daily output for an assembly line is 540 units. This assembly line will operate 720…
A: workstation cycle time = Available Production time / Customer Demand Available Production time =…
Step by step
Solved in 2 steps
- A local toy manufacturer is using a production line that runs 8 hours per day and produces a toy that requires a total of 7 tasks to be performed . The daily demand is 100 toys . Times of the tasks are 2.73,2.01 ,2.13,2.0,2.61,2.71 and 2.95 minutes for A,B,C,D,E,F, and G, respectively . However , due to the nature of the product there are precedencerules that must be observed . Such that Task A does not need any predecessors ; task B requires task A to becompleted . To start task C and task Deach require task B to be completed . Task must be completed prior to stating task E. Task F needs both task and task E to be completed . Finally , task G can start only once task F is completed . Given we apply the most remaining tasks rule for balancing the assembly line , with ties broken according to longesttask time first , the tasks that will be assigned to the THIRD workstation are a. D and F b . None is the correct answer c. D only d. E only e. B, C , and DA local toy manufacturer is using a production line that runs 8 hours per day and produces a toy that requires a total of 7 tasks to be performed. The daily demand is 100 toys. Times of the tasks are 2.73, 2.01, 2.13, 2.0, 261, 2.71, and 2.95 minutes for A, B, C, D, E, F, and G, respectively. However, due to the nature of the product there are precedence rules that must be observed. Such that Task A does not need any predecessors; task B requires task A to be completed. To start task Cand task D, each require task B to be completed. Task C must be completed prior to stating task E. Task F needs both task D and task E to be completed. Finally, task G can start only once task F is completed. What is the minimum number of workstations needed? O a. None of them O b. 8 O c. 4 d. 2 Oe. e to searchA local toy manufacturer is using a production line that runs 8 hours per day and produces a toy that requires a total of 7 tasks to be performed. The daily demand is 100 toys. Times of the tasks are 2.73, 2.01, 2.13, 2.0, 2.61, 2.71, and 2.95 minutes for A, B, C, D, E, F, and G, respectively. However, due to the nature of the product there are precedence rules that must be observed. Such that Task A does not need any predecessors; task B requires task A to be completed. To start task C and task D, each require task B to be completed. Task C must be completed prior to stating task E. Task F needs both task D and task E to be completed. Finally, task G can start only once task Fis completed.Given we apply the most remaining tasks rule for balancing the assembly line, with ties broken according to longest task time first, the tasks that will be assigned to the THIRD workstation are O a. Dand F O b. Eonly O c. Donly O d. None is the correct answer Oe. B, C, and D
- A local toy manufacturer is using a production line that runs 8 hours per day and produces a toy that requires a total of 7 tasks to be performed. The daily demand is 100 toys. Times of the tasks are 2.73, 2.01, 2.13, 2.0, 2.61, 2.71, and 2.95 minutes for A, B, C, D, E, F, and G, respectively. However, due to the nature of the product there are precedence rules that must be observed. Such that Task A does not need any predecessors; task B requires task A to be completed. To start task C and task D, each require task B to be completed. Task C must be completed prior to stating task E. Task F needs both task D and task E to be completed. Finally, task G can start only once task F is completed.Given we apply the most remaining tasks rule for balancing the assembly line, with ties broken according ?to longest task time first, What will the estimated idle time in minutes for FIRST workstation 0.06 .a O None is the correct anser .b O 0.09 .c O 1.00 .d O 1.85 .e O ace 近A local toy manufacturer is using a production line that runs 8 hours per day and produces a toy that requires a total of 7 tasks to be performed. The daily demand is 100 toys. Times of the tasks are 2.73, 2.01, 2.13, 2.0, 2.61, 2.71, and 2.95 minutes for A, B, C, D, E, F, and G, respectively. However, due to the nature of the product there are precedence rules that must be observed. Such that Task A does not need any predecessors; task B requires task A to be completed. To start task C and task D, each require task B to be completed. Task C must be completed prior to stating task E. Task F needs both task D and task E to be completed. Finally, task G can start only once task F is completed.What should be the calculated cycle time in minutes? O a. 0.9 O b. 4.4 O c. None is correct O d. 4.5 O e. 4.8 US PAGE NEXT PAGE MacBA local toy manufacturer is using a production line that runs 8 hours per day and produces a toy that requires a total of 7 tasks to be performed. The daily demand is 100 toys. Times of the tasks are 2.73, 2.01, 2.13, 2.0, 2.61, 2.71, and 2.95 minutes for A, B, C, D, E, F, and G, respectively. However, due to the nature of the product there are precedence rules that must be observed. Such that Task A does not need any predecessors; task B requires task A to be completed. To start task C and task D, each require task B to be completed. Task C must be completed prior to stating task E. Task F needs both task D and task E to be completed. Finally, task G can start only once task F is completed. Given we apply the most remaining tasks rule for balancing the assembly line, with ties broken according to longest task time first, What will the estimated idle time in minutes for FOURTH workstation? O a. 0.06 O b. None is the correct answer О с. 1.85 O d. 1.00 e. 0.09
- A local toy manufacturer is using a production line that runs 8 hours per day and produces a toy that requires a total of 7 tasks to be performed. The daily demand is 100 toys. Times of the tasks are 2.73, 2.01, 2.13, 2.0, 2.61, 2.71, and 2.95 minutes for A, B, C, D, E, F, and G, respectively. However, due to the nature of the product there are precedence rules that must be observed. Such that Task A does not need any predecessors; task B requires task A to be completed. To start task Cand task D, each require task B to be completed. Task C must be completed prior to stating task E. Task Fneeds both taskD and task E to be completed. Finally, task G can start only once task F is completed. Given we apply the most remaining tasks rule for balancing the assembly line, with ties broken according to longest task time first, What will the estimated idle time in minutes for SECOND workstation? Oa. None is the correct answer O b. 0.09 Oc 1.85 O d. 1.00 O e. 0.06A local toy manufacturer is using a production line that runs 8 hours per day and produces a toy that requires a total of 7 tasks to be performed. The daily demand is 100 toys. Times of the tasks are 2.73, 2.01, 2.13, 2.0, 2.61, 2.71, and 2.95 minutes for A, B, C, D, E, F, and G, respectively. However, due to the nature of the product there are precedence rules that must be observed. Such that Task A does not need any predecessors; task B requires task A to be completed. To start task C and task D, each require task B to be completed. Task C must be completed prior to stating task E. Task F needs both task D and task E to be completed. Finally, task G can start only once task F is completed. Given we apply the most remaining tasks rule for balancing the assembly line, with ties broken according to longest task time first, What will the estimated idle time in minutes for THIRD workstation? O a. 1.00 O b. 0.06 O c. None is the correct answer O d. 1.85 e. 0.09A local toy manufacturer is using a production line that runs 8 hours per day and produces a toy that requires a total of 7 tasks to be performed. The daily demand is 100 toys. Times of the tasks are 2.73, 2.01,2.13, 2.0, 2.61,2.71, and 2.95 minutes for A, B, C, D, E, F, and G, respectively. However, due to the nature of the product there are precedence rules that must be observed. Such that Task A does not need any predecessors; task B requires task A to be completed. To start task C and task D, each require task B to be completed. Task C must be completed prior to stating task E. Task F needs both task D and task E to be completed. Finally, task G can start only once task F is completed.Given we apply the most remaining tasks rule for balancing the assembly line, with ties broken according to longest task time first, the tasks that will be assigned to the THIRD workstation are О a. В. С, and D O b. Donly Oc Eonly O d. Dand F None is the correct answer
- A local toy manufacturer is using a production line that runs 8 hours per day and produces a toy that requires a total of 7 tasks to be performed. The daily demand is 100 toys. Times of the tasks are 2.73, 2.01, 2.13, 2.0, 2.61, 2.71, and 2.95 minutes for A, B, C, D, E, F, and G, respectively. However, due to the nature of the product there are precedence rules that must be observed. Such that Task A does not need any predecessors; task B requires task A to be completed. To start task C and task D, each require task B to be completed. Task C must be completed prior to stating task E. Task F needs both task D and task E to be completed. Finally, task G can start only once task F is completed. Given we apply the most remaining tasks rule for balancing the assembly line, with ties broken according to longest task time first, the tasks that will be assigned to the THIRD workstation are O a. E only O b. D and F OC. B, C, and D d. None is the correct answer O e. D onlyA local toy manufacturer is using a production line that runs 8 hours per day and produces a toy that requires a total of 7 tasks to be performed. The daily demand is 100 toys. Times of the tasks are 2.73, 2.01, 2.13, 2.0, 2.61, 2.71, and 2.95 minutes for A, B, C, D, E, F, and G, respectively. However, due to the nature of the product there are precedence rules that must be observed. Such that Task A does not need any predecessors; task B requires task A to be completed. To start task C and task D, each require task B to be completed. Task C must be completed prior to stating task E. Task F needs both task D and task E to be completed. Finally, task G can start only once task F is completed.Given we apply the most remaining tasks rule for balancing the assembly line, with ties broken according to longest task time first, the tasks that will be assigned to the SECOND workstation are, O a. Conly b. None is the correct answer O c. Cand E O d. Eonly O e. A, B, and CA local toy manufacturer is using a production line that runs 8 hours per day and produces a toy that requires a total of 7 tasks to be performed. The daily demand is 100 toys. Times of the tasks are 2.73, 2.01, 2.13, 2.0, 2.61, 2.71, and 2.95 minutes for A, B, C, D, E, F, and G, respectively. However, due to the nature of the product there are precedence rules that must be observed. Such that Task A does not need any predecessors; task B requires task A to be completed. To start task C and task D, each require task B to be completed. Task C must be completed prior to stating task E. Task F needs both task D and task E to be completed. Finally, task G can start only once task F is completed. Given we apply the most remaining tasks rule for balancing the assembly line, with ties broken according to longest task time first, the tasks that will be assigned to the THIRD workstation are O a. E only O b. Dand F O c. None is the correct answer O d. B, C, and D O e. Donly