A mass of 5 kg of saturated liquid-vapor mixture of water is contained in a piston- cylinder device at 100 kPa. Initially, 2 kg of the water is in the liquid phase and the rest is in the vapor phase. Heat is now transferred to the water, and the piston, which is resting on a set of stops, starts moving when the pressure inside reaches 200 kPa. Heat transfer continues until the total volume increases by 30 perrent Dotormino

A mass of 5 kg of saturated liquid-vapor mixture of water is contained in a piston- cylinder device at 100 kPa. Initially, 2 kg of the water is in the liquid phase and the rest is in the vapor phase. Heat is now transferred to the water, and the piston, which is resting on a set of stops, starts moving when the pressure inside reaches 200 kPa. Heat transfer continues until the total volume increases by 30 perrent Dotormino

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

(b) A frictionless piston-cylinder device as shown in Fig. Qlb contains water at 300 kPa and the water is heated at constant pressure from saturated liquid to saturated vapor. Then, the heating process is continued in an isobaric manner until its specific volume reaches the value of 0.7 m'/kg. Water Heat Figure Qlb i) What is the initial temperature of water in the cylinder? ii) What is the final temperature of water in the cylinder? iii) Calculate the total boundary work during the processes, kJ/kg. iv) Calculate the total amount of heat transferred during the processes, kJ/kg. v) Sketch both processes on a T – v diagram with respect to saturation lines.
(b) A frictionless piston-cylinder device as shown in Fig. Qlb contains water at 400 kPa and the water is heated at constant pressure from saturated liquid to saturated vapor. Then, the heating process is continued in an isobaric manner until its specific volume reaches the value of 0.5 m²/kg. Water Heat Figure Q1b i) What is the initial temperature of water in the cylinder? ii) What is the final temperature of water in the cylinder? iii) Calculate the total boundary work during the processes, kJ/kg. iv) Calculate the total amount of heat transferred during the processes, kJ/kg. v) Sketch both processes on a T – v diagram with respect to saturation lines.
A frictionless piston-cylinder device as shown in Fig. Qlb contains water at 400 kPa and the water is heated at constant pressure from saturated liquid to saturated vapor. Then, the heating process is continued in an isobaric manner until its specific volume reaches the value of 0.5 mkg. Water Heat Figure Qlb i) What is the initial temperature of water in the cylinder? ii) What is the final temperature of water in the cylinder? iii) Calculate the total boundary work đuring the processes, kJ/kg. iv) Calculate the total amount of heat transferred during the processes, kJ/kg. v) Sketch both processes on a T – v diagram with respect to saturation lines.
A friction-free, weighted piston-cylinder device contains 2.0 kg of water in a mixed state at a pressure of 150kPa and a quality of 0.60. As it sits there, heat is lost until the mixture becomes entirely a saturated liquid. How much heat is lost jn the process?
Piston Water A piston cylinder system initially contains 2.0 kg of water at 0.3 MPa ad 20% quality. Water is heated at the constant pressure until the piston hits the stops. At this instance, the total volume in piston cylinder system is 1.0 m. Heat addition is continued until water is saturated vapor. Calculate the heat transfer during this process, in kJ.
H.W: - 0.8m of gas at 8bar and 27°C is compressed isothermally until its volume is ¼ time the original volume, then its heated at constant pressure to original volume, finally its cooled at constant volume to original condition. Find: - a- the heat transferred. b- Work done c- Change in internal energy. (draw the processes on p-v diagram) Take cp=1.01kj/kg.k, R=0.28kj/kg.k
2. Saturated liquid water at 250 kPa is contained in a piston-cylinder device as shown in the figure below. The total initial volume is 0.012m'. As the water is heated, the pressure inside the cylinder remains constant until the piston hits the stops. When the piston hits the stops the specific volume is 0.47443 m/kg. Heat transfer to the water continues until the pressure doubles. NOTE: If needed use the closest value in tables 3 to avoid interpolation. Use 5 decimal digits when using specific volume. a.) Plot the process in a P-v-diagram with respect to saturations lines. b.) Fill de table below c.) Determine the total mass P(kPa) T(°C) v(m'/kg) h(kJ/kg) Phase 2 3.
The tank of a leaky air compressor originally holds 90 L of air at 33deg C and 225 kPa. During a compression process, 4 grams of air is lost; the remaining air occupies 42 L at 550 kPa. What is the temperature of the remaining inair in degree centigrade.
The tank of a leaky air compressor originally holds 90 L of air at 33deg C and 225 kPa. During a compression process, 4 grams of air is lost; the remaining air occupies 42 L at 550 kPa. What is the temperature of the remaining in air in degree centigrade.
A 2.8 m^3 rigid tank is filled with saturated liquid vapor mixture of water at 300C. If 2% of its volume is liquid and the rest is vapor, the total mass in the tank in kg is?
A piston-cylinder set up contains 0.015 kg of an ideal gas at a volume of 1 liter, a temperature of 5.5 degrees Celcius, and a pressure of 685 kPaa. The gas is heated at constant pressure to 1.75liters. If the total heat input for the process was 2.78 kJ, Find: а. Ср b. R c. Cv
1.A piston-cylinder containing air expands at a constant pressure of 150 KPa from a temperature of 285 K to a temperature of 550K.The mass of air in the cylinder is .05 Kg. Determine the system heat and work for the process