A mild steel specimen of Initial diameter of53.5 mm is turned to final diameter of 47 mmfor an initial length of 154 mm on a lathemachine.Using the given data find the following.(i) Feed of 0.4 mm/rev & Depth of cut is 0.5mm(ii) During machining the tool's approachlength is 5 mm, over run length is 2mm(iii) Total time required to complete theturning operation is 59.6 minutes(a) Find number of passes to finish the entireturning operation ((b) The actual length of the turning operationin mm ('

for solution refer below images.

Answered: A mild steel specimen of Initial…

A mild steel specimen of Initial diameter of 53.5 mm is turned to final diameter of 47 mm for an initial length of 154 mm on a lathe machine.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A mild steel specimen of Initial diameter of 51.5 mm is turned to final diameter of 48 mm for an initial length of 151 mm on a lathe machine. Using the given data find the following. (i) Feed of 0.1 mm/rev & Depth of cut is 0.5 mm (ii) During machining the tool's approach length is 7 mm, over run length is 2mm (iii) Total time required to complete the turning operation is 48.8 minutes (a) Find number of passes to finish the entire turning operation (b) The actual length of the turning operation in mm ( (c)The time required to complete one single turning operation in minutes (d) Spindle speed in rpm
A mild steel specimen of Initial diameter of 32.5 mm is turned to final diameter of 25 mm for an initial length of 154 mm on a lathe machine. Using the given data find the following. (i) Feed of 0.3 mm/rev & Depth of cut is 0.5 mm (ii)During machining the tool's approach length is 6 mm, over run length is 3mm (iii) Time required to complete one single turning operation is 2.3 minutes (a)Find number of passes to finish the entire turning operation (b) Total time required to complete the turning operation in minutes (c) Spindle speed in in rpm (d) Cutting speed in m/minutes
A mild steel specimen of Initial diameter of 30.5 mm is turned to final diameter of 27 mm for an initial length of 153 mm on a lathe machine. Using the given data find the following. (i) Feed of 0.4 mm/rev & Depth of cut is 0.5 mm (ii)During machining the tool's approach length is 5 mm, over run length is 2mm (iii) Time required to complete one single turning operation is 3.5 minutes (a)Find number of passes to finish the entire turning operation (b) Total time required to complete the turning operation in minutes
A mild steel specimen of Initial diameter of 30.5 mm is turned to final diameter of 27 mm for an initial length of 153 mm on a lathe machine. Using the given data find the following. (i) Feed of 0.4 mm/rev & Depth of cut is 0.5 mm (ii)During machining the tool's approach length is 5 mm, over run length is 2mm (iii) Time required to complete one single turning operation is 3.5 minutes (c) Spindle speed in in rpm (= (d) Cutting speed in m/minutes(=
The end of a large tubular workpart is to be faced on a NC vertical boring mill. The part has an outside diameter of 38.0 in and an inside diameter of 24.0 in. If the facing operation is performed at a rotational speed of 40.0 rev/min, feed of 0.015 in/rev, and depth of cut of 0.180 in, determine (a) the cutting time to complete the facing operation and the cutting speeds and metal removal rates at the beginning and end of the cut.
Q24. For the below figure please write its part program. The depth of the cut is 0.25 inches (Finishing operation), while the tool's diameter is 0.5 inches. Consider the speed and feed. -0.75- - - 1.0 60⁰ RO.25 (0, 0) 0.75-
The face milling cutter of D = 200 mm used to cut a block which is 200 mm H, 1=480 mm, if f- 0.7 mm/rev is used and the overrun of the cutter is 12 mm and cutting speed 320 mm/min. Calculate the machining time. Cuttin
Taper turning is performed on a mild steel specimen, using the given data determine the following. of () Large diameter of the taper is 31.5 mm (ii) Spindle speed is 190 rpm, feed is 0.2 mm/rev & Depth of cut is 0.5 mm tion (ii) 1.5 minutes and 17.7 minutes are respective time required to complete one single taper turning operation and total time required to complete the taper turning operation Find (a) Cutting speed in m/minutes - (* (b) Taper Length in mm - (1 (c) Taper angle in degree
Q1. Calculate the time required to machine a workpiece 170 mm long, 60 mm diameter to 165 mm long 50 mm diameter. The workpiece rotates at 440 rpm, feed is 0.3 mm/rev and maximum depth of cut is 2 mm. Assume total approach and overtravel distance as 5 mm for turning operation. Answer Q2. A gray cast iron surface 280 wide and 540mm long may be machined either on a vertical milling machine, using a 100mm - diameter face mill having eight inserted HSS teeth, or on a horizontal milling machine using an HSS slab mill with eight teeth on a 200-mm. diameter. Which machine has the faster cutting time? The values of feed per tooth and cutting speed for both processes are 0.4mm/tooth and 80m/min, respectively. The depth of cut = 3.0 mm and assume A and O equal to 5. Answer
Exercises 4 1. A 30 mm diameter mild steel bar is being turned at a spindle speed of 8 rev/s, on a multi-tool centre lathe having eight tools in operation. The feed is 0-3 mm/rev, the specific cutting pressure/tool is 2 000N/mm and the total power consumed for the operation is 14 kW. If the depth of cut is to be kept the same for each tool, calculate the depth of cut/tool in mm.
The surface finish specification in a turning job is 0.90 um. The work material is cast iron. The cutting conditions have been selected as follows: v =90 m/min, f -0.23 mm/rev, and d = 2.2 mm. The nose radius of the cutting tool must be selected. Determine the minimum nose radius that will obtain the specified finish in this operation. oichie 0 90. m The wok matedal i material is
A drilling operation is performed to create a through hole on a steel plate that is 20 mm thick. Cutting speed = 0.4 m/s, and feed = 0.20 mm/rev. The 18-mm-diameter twist drill has a point angle of 120°. Determine the following once the drill reaches full diameter: a. the machining time and, b. the metal removal rate Equation used Tm TD₂L fv