A new manufacturing plant which operates on parameters such as temperature and pressure, has been procured by your company. In the operational manual is stated “if one or more than one parameter exceeds the safe value, a protective measure is needed to be done”. As an engineer, design a schematic diagram using an OR gate to detect the exceed parameter and explain how it will produce a command signal for the system to take the required action. Major Topic 12 Basic logic gates & its application AN

A new manufacturing plant which operates on parameters such as temperature and pressure, has been procured by your company. In the operational manual is stated “if one or more than one parameter exceeds the safe value, a protective measure is needed to be done”. As an engineer, design a schematic diagram using an OR gate to detect the exceed parameter and explain how it will produce a command signal for the system to take the required action. Major Topic 12 Basic logic gates & its application AN

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter13: Magnetic Induction

Section: Chapter Questions

Problem 1PA

See similar textbooks

Similar questions

This is a logic gate simplification with certain laws to be followed. Please read the instructions on the given image, I will like your answer if you answered it properly and accurately. Thank you in advance
Digital Logic Design Show the Diagrams, please as well. Must answer according to the Questions exactly.
Book used is Digital Logic with Verilog Design by Brown & Vranesic. Study the counting circuit diagram below and answer the following questions: a. Based on the circuit drawing, is the Clock Positive-Edge Triggered or Negative-Edge Triggered? b. How was this determination made? c. What are the minimum and maximum valkues of the circuit? Explain. d. There are 3 grayed out boxes we refer to this symbolic use as _____________. Why are these used in circuit design?
There are 5 gates in a metrobus, 1 of which is to get on and 4 to get off. The number of passengers inside is desired to be seen on the LCD connected to the P2 port. Get-on gate is controlled by the P0.2 while get-off gates are controlled by the P0.3, P0.4, P0.5, and P0.6. The sensors generate Logic-1 while passing passengers. Since the passenger carrying capacity of the metrobus is 294, if the number of passengers exceeds the number of 294, the warning LED connected to the P0.7 pin is required to light up. Since other pins of P0 are used for other purposes, it is not desired to be changed. Can you write the answer with assembly code using 8051 - AT89S8253 architecture?
Question 5(a)(i) Discuss in detail, the working of Full Adder logic circuit and extend your discussion to explain a binary adder, which can be used to add two binary numbers.(ii) With relevant logic diagram and truth table explain the working of a two input EX-OR gate.
Need Part B (a) Suppose a two-way switch logic needs to be implemented in a staircase of a building, where a lamp can be controlled by two switches. You are required to analyze below conditions, and provide a PLC based system capable of operating according to the below mentioned conditions • If both the switches are in same state, i.e., both are off or both are on, then lamp will be in "ON" state. If anyone of the switches is "ON" and other is "OF", then lamp will be in "OFF" state. When the lamp is OFF, users can turn it on by changing the state of either switch 1 or switch 2. • Likewise, when the light is ON, users can turn off the light by changing the state of one of the two switches. 2. Suppose you are required to control a motor ON, OFF operation with two push buttons using PLC. Control System should work according to following conditions: When motor is off, and 1" push button is pressed, motor will start and stay in on state even after release of push button. When 2nd push…
Provide at least 3 challenges experienced in designing a digital system with sequential logic circuit components. Explain each comprehensively.
State in detail the reason why logic circuits are minimized
This question contains info on Digital Systems Logic Design and requires: Truth Table, KMapping and the Logic Circuits Designs. SEND the accurate answers labelled please.
Create a synchronous counter utilising J-K flip-flops that may be utilised for a 7-story building's elevator system, as depicted in figure below. Assume the ground floor is considered the 0th floor. Assume that level 2 and level 7 cannot be reached because they are only accessible to authorised individuals. Provide the smallest number of logic gates in the logic circuit design.
is it possible to connect the outputs of a comparator to a logic gate (connected to an led)? The led connected to the logic gate lights up if the inputs of the comparator both satisfy a condition, for example, the voltage of both inputs are less than the reference voltages.
Implementation of Combinational Functions using various Logic Gates