A pipe in a manufacturing plant is transporting superheated vapor at a mass flow rateof 0.3 kg/s. The pipe is 10 m long, has an inner diameter of 5 cm and pipe wall thicknessof 6 mm. The pipe has a thermal conductivity of 17 W/m.K, and the inner pipe surfaceis at a uniform temperature of 120 °C. The temperature drop between the inlet and theexit of the pipe is 7 °C, and the constant pressure specific heat of vapor is 2190 J/kg.°C.If the air temperature in the manufacturing plant is 25°C, determine the heat transfercoefficient as a result if convection between the outer pipe surface and the surroundingair.T(r) = 120°CSuperheatedAir, 25°Cr2vaporr10.3 kg/sL = 10 mTin-Tout = 7°C

Answered: A pipe in a manufacturing plant is…

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter7: Forced Convection Inside Tubes And Ducts

Section: Chapter Questions

Problem 7.4P

See similar textbooks

Similar questions

350 pipes are fixed as square in a pipe bundle used for condenser. PipeThe outer diameters are 8 mm and the steam at 0.2 bar is desired to be condensed on the pipes. pipe outer The surface temperature is kept constant at 30 °C. If the length of the pipes is 1.5 m, the heat transferred in the systemCalculate the amount of energy and the amount of condensed steam
A copper rod whose diameter is 2 cm and length 50 cm have one end in boiling water, the other end in a jacket cooled by flowing water which enters at 10oC. The thermal conductivity of the copper is 0.102 kCal/m-soC. If 0.20 kg of water flows through the jacket is 6 min, by how much does the temperature of the water increase?
HEAT TRANSFER,PLEASE GIVE COMPLETE WORKING Hot air at 80ºC enters an 8-m-long pipe at a rate of 0.15 kg/s. The pipe is considered as thin wall with diameter of 20 cm. The wall of the pipe is observed to be nearly at isothermal at 60ºC. The fluid properties of the hot air is as given on Table 1. Determine: The temperature of the air at the exit of the pipe. The heat loss from the hot air. Table 1: Thermo-physical properties for hot air k = 0.02953 W/m·K µ = 20.96×10-6 N·s/m2 Pr = 0.7154 cp = 1008 J/kg·K
43% uo 7:52 * ZAIN IQ I. sheet No.3.pdf Homework 01-03 -2021 one-dimensional heat transfer and disregarding radiation, determine the rate of heat transfer through the wall. Q4/ Steam at Te1-320°C flows in a cast iron pipe (k=80W/m.°C) whose inner and outer diameters are D =5cm, and D=5.5cm, respectively. The pipe is covered with 3 cm thick glass wool insulation with k=0.05W/m.°C. Heat is lost to the surroundings at T02=5°C_by natural convection and radiation, with a combined heat transfer coefficient to be h,=18W/m.C. Taking the heat transfer coefficient inside the pipe to be h,=60W/m.C, determine the rate of heat loss from the steam per unit length of the pipe. Also determine the temperature drops across the pipe shell and the insulation. 05/ Determine the overall heat transfer coefficient U based on the outer surface of a D=2.5cm, and D=3.34 cm steel pipe (k=54.0W/m.°C) for the following conditions: inside and outside heat transfer coefficients are 1200W/m."C. and 2000W/m."C…
Water is entering a heated tube at mass ow rate of 1.2 kg/s. The temperature at the inlet is 20 C and at the outlet is 80 C. Assume the surface temperature of the tube is 100 C. The convection coe cient of the water ow is 28 W=m2 C. The speci c heat and density of water can be assumed to be 4180 J=kg C and 990 kg=m3. What is the rate of heat transfer to water during this proces
Water flows in a 3.5-cm-diameter pipe so that the Reynolds number based on diameter is 2000 (laminar flow is assumed). The average bulk temperature is 10◦C. What would the heat transfer coefficient be in W/m2-°C for such a system if the tube wall was subjected to a constant heat flux and the velocity and temperature profiles were completely developed? Evaluate properties at bulk temperature.
Heat Transfer (Third year) 2020- 2021 Homework 01-03-2021 By Dr. Basil Noori Merzah one-dimensional heat transfer and disregarding radiation, determine the rate of heat transfer through the wall. Q4/ Steam at T01-320°C flows in a cast iron pipe (k=80W/m. C) whose inner and outer diameters are D,=5cm, and D,-5.5cm, respectively. The pipe is covered with 3 cm thick glass wool insulation with k=0.05W/m. C. Heat is lost to the surroundings at T2-5°C by natural convection and radiation, with a combined heat transfer coefficient to be h,=18W/m."C. Taking the heat transfer coefficient inside the pipe to be 2 0 h,-60W/m. C, determine the rate of heat loss from the steam per unit length of the pipe. Also determine the temperature drops across the pipe shell and the insulation. Q5/ Determine the overall heat transfer coefficient U based on the outer surface of a D=2.5cm, and D =3.34 cm steel pipe (k=54.0W/m. C) for the following conditions: inside and outside heat transfer coefficients are…
An coconut oil (considered as viscous fluid) must be pumped between two buildings in an agro-industrial plant through an AISI 304 stainless steel pipe spread on the ground that has an outside diameter of 22 cm and 110 m long. To facilitate pumping, the liquid will be heated to 40 ° C in order to reduce its viscosity. The oil flow rate will be 20 Kg / s and the specific heat will be 1300 J / Kg K. Determine the temperature drop that the liquid will experience along the pipeline under the following operating conditions:Ambient air temperature = 10 ° CWind speed = 14 m / sPipe surface temperature = 37 ° C
Palm oil with a density of 1200 kg/m3 and the specific heat of 2 kJ/(kg.K) is to be heated from 20oC to 80oC before further processing. The oilplaced in a vessel (vessel) cylindrical upright with a diameter of 2 meters.The height of the oil vessel inside is 2 meters. For this purpose, an electric heating element with an electrical resistance type of heat is used.The electrical resistance used is a 2 mm diameter conductor wire wrappedwith magnesium oxide material with a thermal conductivity of 0.4 W/(m.K) thick 2.5 mm, then coated with the outermost metal 0.5 mm thick. Occurring power density on the outermost metal layer should not be more than 25 kW/m2. Warm-up time is expected to be only about 1.5 hours. Calculate: a) Required electrical power? (in kW) b) Rating of the heater by meter length? c) Maximum temperature of the heater element?
Oil is flowing through a 50 mm-ID and 55 mm-OD pure iron pipe at 1 m/s. It is being heated by steam outside the pipe and steam film coefficient may be taken as 11 kW/m2°C. At a particular point along the pipe, the oil is at 50°C, its density is 880 kg/m³, its viscosity is 2.1 cP, its thermal conductivity is 0.135 W/m°C and its specific heat is 2.17 J/g°C. What is the overall heat transfer coefficient at this point, based on the inside area of the pipe? If the steam temperature is 130°C, what is the heat flux at this point, based on the outside area of the pipe?
Example: 0.5 kg of water per minute is heated from 20° to 40°C when passed through a tube of 2.5 cm diameter steel pipe. The pipe surface temperature is maintained at 110°C by condensing steam on its surface. Find out the length of the pipe required. The properties of water at mean temperature of 70°C are given below: p = 978 kg/m² k= 0.575 W/m. K Cp = 4200 J/kg. K v = 0.415 x 10-6 m²/sec
Shown in the figure,a card is cooled with water. To cool the cardWater 0.4 m / s in the circular pipe system placed on the bottomaverage speed and entering at a temperature of 20 oC, at a temperature of 24 oCcomes out. Electronic components on the board of 1.5 kWthey produce energy. At the same time, from the card surface to the mediumApproximately 0.05 kW of heat loss occurs by convection. Continuous flowFind the mass flow rate of the water for the conditions. Specific heat of waterYou can get = 4.22 as ?? / ???.

SEE MORE QUESTIONS

Recommended textbooks for you

Principles of Heat Transfer (Activate Learning wi…

Mechanical Engineering

ISBN:

9781305387102

Author:

Kreith, Frank; Manglik, Raj M.

Publisher:

Cengage Learning