A pipe tapers over 60m from 450mm in diameter to 675mm in diameter. The gauge pressure at the inlet is 75 kN/m2 and the gauge pressure at the outlet is 90 kN/m2. If the centreline of the pipe rises at a gradient of 1 in 80 and the energy loss due to friction is 0.01m per metre length determine the flowrate in the pipeline and the velocity at entry and exit.

A pipe tapers over 60m from 450mm in diameter to 675mm in diameter. The gauge pressure at the inlet is 75 kN/m2 and the gauge pressure at the outlet is 90 kN/m2. If the centreline of the pipe rises at a gradient of 1 in 80 and the energy loss due to friction is 0.01m per metre length determine the flowrate in the pipeline and the velocity at entry and exit.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

4. A pipe carries oil of density 800 kg/m³. At a given point (1) the pipe has a bore area of 0.005 m² and the oil flows with a mean velocity of 4 m/s with a gauge pressure of 800 kPa. Point (2) is further along the pipe and there the bore area is 0.002 m² and the level is 50 m above point (1). Calculate the pressure at this point (2). Neglect friction. (374 kPa)
Water (ρ = 1000 kg/m3) is flowing vertically in the pipe shown below. The top, middle, and bottom parts have radii of r1 = 3 cm, r2 = 1 cm, and r3 = 3 cm, respectively. The speed of water flow and the gauge pressure at point 1 are v1 = 20 cm/s and P1 gauge = 200 Pa. The height difference between point 1 and 2, point 2 and 3 is 10 cm. Use g = 10 m/s2 for the acceleration due to gravity. What is the speed of the water flow at point 2? What is the gauge pressure at point 2? What is the speed of the water flow at point 3? What is the gauge pressure at point 3?
Water is transported in a pipe, at an average flow rate of Q = 50 L/s. Calculate the pressure difference p between the 2 manometers. We can assume that the energy losses by friction are negligible, and that there are only singular energy losses (be careful to identify ALL the singularities). The pump adds an energy of HP = 10 m to the system. "GATE VALVE" P2 OUVERTURE COMPLÈTE do = 150 mm Q = 50 L/s • 2) 2 m Q = 50 L/s COUDES À POMPE RAYONS COURTS do = 150 mm (Hp = 10 m)
please answer asapWater flows downwards in a vertical pipeline of gradually varying section from point 1 to point 2, which is 1.5m above point 1, at the rate of 0.9m^3/s. At section 1 the pipe diameter is 0.5m and pressure is 800 kPa. If pressure at section 2 is 600 kPa, determine the pipe diameter at that location. Neglect losses
Oil flows from a tank through a 50 mm diameter pipe. If the average velocity is 1,3 m/s, determine how long it will take for 2,5 tons of oil to flow out? Take Peil = 780 kg/m.
Find an expression for the velocity of water leaving the sprinkler. Find an expression for the gauge pressure at point A, a distance L1, upstream of the narrow pipes. Express the answer in terms of the flowrate, Q. The inner diameter of the first segment of the pipe is d1=10mm, the inner diameter of the second set of pipes is d2=1mm, with N=25. The flowrate through the sprinkler is Q=0.2 L/s. Flow in pipes typically becomes turbulent when the Reynolds number exceeds 2000. Comment on the accuracy of the assumption that the flow could be treated as laminar everywhere. May be assumed water has a density of 1000kg/m^3 and a viscosity of 1mPa s.
Flow takes place between three reservoirs, as shown in Figure 1. The volume flow rate out of reservoirs A and B is 0.15 m3/s and 0.25 m 3 /s respectively. If the coefficient of friction for the three pipes is 0.008, determine the relative elevations of the free surfaces. Neglect all losses other than friction. Below attached is the sketch
Water is pumped at a rate of 21.4 m/s from tank (A) and out through a 300.5 m pipe to tank (B). The surface roughness of the pipe is 0.046 mm. When the water levels are as shown in the given figure, the head provided by the pump is 70 m, Calculate the pipe diameter (mm) if the water temperature is 10°C (do not assume the water mass density and the ViScosity), Usef 0.02 for the first iteration and try only one more iterations (two in total) by using Swamee and Jain formula. Elevation 135 Elevation 140 m Tank (B) Tievation 100m Tank LA) Jund: Elevitions in Write the answer for any numbers after the declmal
Consider the wind tunnel shown below. The diameter at section 1 is 0.9 m and the diameter at section 2 is 0.4 m. A manometer is used to determine the pressure difference between the two sections. The manometer liquid has a specific gravity of 0.82. Determine the change in height in the manometer if the velocity at section 2 is 66 m/s. Assume incompressible flow and standard sea-level conditions. Provide answer in centimeters. Round-off answer to the nearest whole number.
In a tapered horizontal pipeline, the seawater's speed is 3.75 m/s and the gauge pressure is 21 kPa at the first point. Find the gauge pressure at a second point in the line if the cross-sectional area at the second point is thrice that at the first.
In the following figure, a machine is installed in the water drainage system. Knowing that the machine's efficiency is 75%, obtain the flow direction, whether the machine is a pump or a turbine and its power.The pressure measured by the manometer above the machine is equal to 150 kPa and the pressure loss is given by lw= K* u2b / 2(m2/s2). Between sections (1) and (2), K1-2 = 3.0, and between sections (2) and (3), K 2-3 = 1.5. D = 15 cm, ρ= 103 kg/m3 and 1HP = 745,7 W (watt)
= 4.33 9.74m/ seć n/ 4(0.2)2 HOMEWORK Q1l A (30 N/s) flow throw the reducer of the proceeding problem ,the air in the (300mm) pipe having weight density of (9.8 N/m' ) in the flowing through the reducer producing a redaction of density .assuming that the weight density of the air in the (200 mm) pipe is (7.85 N/ m'). Calèulate the mass and volume flow rate. Q2/ (2) Water enters a conical diffusing passage (see Figure below). With a flow rate of 10ft'/s, and if the entrance cross-section area is 2 ft, what's the average velocity at the entrance to the diffuser? What must the diffuser exit area be to reduce the velocity to 0.5 ft/s? 4 = 2 f Q = 10 cfs - m = AQ: oiclooleo or boon ow.matve binl to sinsb omit letot odi stum hn th .C