A plaque assay is performed beginning with 1 mL of a solution containing bacteriophages. This solution is serially diluted 4 times by combining 0.1 mL of each sequential dilution with 9.9 mL of liquid medium. Then 0.1 mL of the final dilution is plated in the plaque assay and yields 21 plaques. What is the initial density of bacteriophages in the original 1 mL? Recall that initial phage density = (plaque number/mL) ×× (dilution factor).

A plaque assay is performed beginning with 1 mL of a solution containing bacteriophages. This solution is serially diluted 4 times by combining 0.1 mL of each sequential dilution with 9.9 mL of liquid medium. Then 0.1 mL of the final dilution is plated in the plaque assay and yields 21 plaques. What is the initial density of bacteriophages in the original 1 mL? Recall that initial phage density = (plaque number/mL) ×× (dilution factor).

Basic Clinical Laboratory Techniques 6E

6th Edition

ISBN:9781133893943

Author:ESTRIDGE

Publisher:ESTRIDGE

Chapter2: Basic Hematology

Section2.3: Microhematocrit

Problem 3RQ

See similar textbooks

Similar questions

Considering counting rules, calculate the initial titre of the sample viral stock if the following plaques were counted in a plaque assay. Show clear sample calculations. Table 1: Plaque assay counts for lambda phage stock titre enumeration of average concentration (PFU/mL) Total dilution of viral stock 1/13500000 1/135000000 1/135000000 plated Volume diluted viral stock 0.1 0.1 0.1 plated (mL) PFU replicate 1 TNTC 275 25 Calculated concentration (PFU/mL) replicate 1 PFU replicate 2 TNTC 239 23 Calculated concentration (PFU/mL) replicate 2 Average concentration (PFU/mL)
A plaque assay is performed beginning with 1 mL of a solution containing bacteriophages. This solution is serially diluted three times by combining 0.1 mL of each sequential dilution with 9.9 mL of liquid medium. Then 0.1 mL of the final dilution is plated in the plaque assay and yields 17 plaques. What is the initial density of bacteriophages in the original 1 mL?
A plaque assay is performed beginning with 1 mL of a solution containing bacteriophages. This solution is serially diluted 3 times by combining 0.1 mL of each sequential dilution with 9.9 mL of liquid medium. Then 0.1 mL of the final dilution is plated in the plaque assay and yields 12 plaques.What is the initial density of bacteriophages in the original 1 mL? Enter your answer to two significant figures ( for example: 1.1 * 10^2)
Please DESCRIBE, in outline form, the method you will use to select for bacterial cells that have taken up the pL311 plasmid, and to screen those cells for the presence of plasmids that are likely to contain a cloned gene. Be sure to mention the specific media you will use. In addition, please explain the rationale behind this specific selection and screening procedure. (Remember that you have available the following types of media: (i) media containing neither kanamycin nor X-gal, (ii) media containing BOTH kanamycin and X-gal, (iii) media containing tetracycline, and (iv) media containing ampicillin.
In a protocol for DNA sample preparation for agarose gel electrophoresis, what volume of 4X loading buffer must be added to 21 micro L of DNA to obtain a 1X buffer solution?
Elaborate on three (3) lysis methods used to disrupt bacterial cells. During DNA isolation using P: C: I technique, a precipitation step is required. What is the purpose of this step? How can sodium acetate and ethanol facilitate the precipitation step in DNA isolation?
What are DNA probes Describe three (3) methods that can be used to label DNA probes Describe 2 methods for detection of the hybridized probe List the advantages of using non-radioactively labeled probes vs radioactively labeled probes.
Choose two genes from Figure 4.6 and draw a graph to represent the change in transcription over time.
During incubation, prepare dilutions of the standard antiserum which constitutes the standard curve for the assay (concentration in ng/mL). Add 500 µL of PBS-milk to the supplied microtube containing 500 µL of standard antiserum to obtain Standard 1 [500 ng/mL]. Identify seven microtubes for standards 2 to 7 and place 500 µL of PBS-milk in each. Calculate how much of antiserum is used in each standard ?
A cloning vector map is shown below. EcoRI Bam Ban Hind P-galactosidase Amp Bam Bam EcoRI Ori C Which restriction site is best for inserting a DNA fragment for selection of chimeric plasmid containing colonies? 1) They're all equally good. 2) Hindll 3) EcoRI 4) BamHI
These are the results after running Agarose Gel Electrophoresis of the cut/uncut pUC19 plasmid and isolated Genomic DNA at 120 V for 30 minutes. Can you explain what this gel means?
A phagehunter performs a spot titer using standard techniques (3 ul of each dilution spotted to lawn) of a lysate obtained from an optimum webbed plate experiment. The phagehunter counts 8 plaques on the 10-7 dilution spot. Which of the following scenarios is the best choice for the phagehunter to do next? a.) The phagehunter has not achieved a high enough titer lysate to move forward with characterization experiments, so they should go back to the pick-a-plaque experiment. b.) The phagehunter has not achieved a high enough titer lysate to move forward with characterization experiments, so they should adopt a phage from direct isolation. c.) The phagehunter has not achieved a high enough titer lysate to move forward with characterization experiments, so they should try to make more optimum webbed plates. d.) The phagehunter has achieved a high enough titer lysate to move forward with characterization experiments.