A pulley system is carrying a 90 kg object as shown in Figure Q5. The total weight and the radius of gyration of wheel A are 50 kg and 15cm. The motor produces a torque of M = 70 Nm while pulley B is attached to the motor. Draw the free body diagram and determine the velocity if the box after 5 revolutions is made by pulley B. 20 cm 8 cm 10 cm

A pulley system is carrying a 90 kg object as shown in Figure Q5. The total weight and the radius of gyration of wheel A are 50 kg and 15cm. The motor produces a torque of M = 70 Nm while pulley B is attached to the motor. Draw the free body diagram and determine the velocity if the box after 5 revolutions is made by pulley B. 20 cm 8 cm 10 cm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In a four bar mechanism the link AB rotates with angular velocity of 20rad/s and angular acceleration of 100 rad/s both in clockwise direction when it make an angle of 45° with link AD which is fixed .The length of various linkages are AB=CD=400 mm,BC=500mm and AD=750mm .Neglect the gravitational effect and friction.The mass of link is 5kg/m. Find the torque on output link E (2) (4) A (1) (1)
An engine is fitted with a flywheel that has a mass of 22.5 kg and has a radius of gyration of 0.2 m. The load torque is constant and the crankshaft torque can be represented by the expressionTorque = 4a + a sin θ + a sin 2θwhere θ is the crank angle.When the engine develops 7.5 kW at 600 revs/min, find:(a) The crank angle at which the engine torque is equal to the loadtorque(b) The coefficient of cyclical speed fluctuation(c) The maximum angular acceleration of the flywheel.
The slender-bar assembly B (Figure 4) has a mass per unit length of 5 kg/m and is mounted on the shaft A. The shaft is subjected to a torque of M = 0.5/t N•m (where t is in seconds). Calculate the angular velocity of the assembly B when t=3 s, starting from rest. Neglect the mass of shaft A. 500 mm A M 100 mm 100 mm Figure 4.
Q1: The turning-moment diagram for a petrol engine is drawn to a vertical scale of 1mm = 500 N.m and horizontal scale of 1mm = 3. The turning moment diagram repeats itself after every half revolution of the crankshaft. The areas above and below the mean torque line are 260, -580, 80, -380, 870, and -250mm². The rotating parts have a mass of 55 Kg and radius of gyration of 2.1m. If the engine speed is 1600 rpm, determine the coefficient of fluctuation of speed. 34x139 2
A gear of mass m = 10 kg and radius R=0.25 m may rotate about its center of mass C, which is fixed. A rack of mass m = 10 kg is subjected to a constant force Fo = 20 N, as shown. The rack and gear are geared together (gear teeth not shown), so that the force Fo drives the rack to the right and rotates the gear. Find the angular ácceleration a of the gear and find the force f exerted by the rack on the gear. The gear is to be modeled as a uniform circular disc. Fixed Fo3 20 N Rack
A constant torque of 2kN-m is exerted on a crankshaft to start the engine.The flywheel has a mass of 1800kg and a radius of gyration 1m .If there is a resisting torque of 1kN-m,find the speed of the engine after 1 minute.
1. The 60-lb flywheel has a radius of gyration about its shaft axis of ko = 15 inches. Starting at 1 = 0 with a speed of 90 rpm, the flywheel is subjected to a torque that will stop the flywheel in 10 s. The torque M ramps up from 0 to Mmax in 3 s, then holds steady at Mmar until stopped. What must be the value of Mmar?
The turning-moment diagram for an engine consists of two isosceles triangles each with a height equivalent to a torque of 16kNm. The bases of the triangles lie between ? = 0 ? and ? = 180? , and ? = 180? and ? = 360? Sketch the turning-moment diagram and add the mean torque line. If the engine is to rotate with a mean speed of 130 rpm, calculate the following: the power developed the mass of the flywheel having a radius of gyration 1.1m to restrict the fluctuation of speed to +1.5% of the mean speed. Demonstrate which would be most effective to reduce the fluctuation of speed, a change in diameter of or a change in mass of the flywheel.
Gear A on the drive shaft of the outboard motor has a radius ra=9 in. and the meshed pinion gear B on the propeller shaft has a radius rg-53 in. The point P is located on the propeller's tip at a distance 4 in. from the neutral axis of the propeller's shaft. نند P B At the beginning of the propulsion, the drive shaft rotates with an angular acceleration a = A. t 2.0 rad.s2 where t is in seconds. what must be the value of A to have, while starting from rest, vp=24 in.s¹¹ in 6 seconds ?
The two 1-kg gears A and B are attached to the ends of al 3-kg slender bar. The gears roll within the fixed ring gear C, which lies in the horizontal plane. (Figure 1) Figure 150 mm 400 mm- 150 mm Part A If a 10-N m torque is applied to the center of the bar as shown, determine the number of revolutions the bar must rotate starting from rest in order for it to have an angular velocity of WAB = 22 rad/s. For the calculation, assume the gears can be approximated by thin disks. Express your answer using three significant figures. ►View Available Hint(s) the number of revolutions = Submit Provide Feedback VAE vec ? Next >
5. The pendulum shown below consists of a 30 kg point mass at the end of a uniform bar with mass m = 45 kg and length L = 2 m. The pendulum moves in a vertical plane while acted upon by a 500 N-m torque as shown. If the pendulum's angular velocity is 4 rad/s when 0 = 90 degrees, how much force is exerted on the pendulum by the pin at point A when 0 = 330 degrees? 500 N-m B F = 2470 N Z -52 degrees
In the mechanism shown below, the wheel is pinned at the center. The radius from O to C is 0.2 m and link CB is 0.55 m long. CB makes an initial angle of 25° with the horizontal as shown. The hydraulic ram at B is moving left at 7 m/s. At the moment shown, what is the angular velocity of link BC and the wheel pivoted at 0? 0000 Ninbet tatis rad/s