A resistor with resistance 31.5 Q is connected to the terminals of a voltage source. (a) Calculate the current through the resistor when the voltage is set at 7.00 V. A (b) Calculate the power dissipated by the resistor when the voltage is set at 7.00 V. W (c) If the voltage is doubled, recalculate the power. W

A resistor with resistance 31.5 Q is connected to the terminals of a voltage source. (a) Calculate the current through the resistor when the voltage is set at 7.00 V. A (b) Calculate the power dissipated by the resistor when the voltage is set at 7.00 V. W (c) If the voltage is doubled, recalculate the power. W

Principles of Physics: A Calculus-Based Text

5th Edition

ISBN:9781133104261

Author:Raymond A. Serway, John W. Jewett

Publisher:Raymond A. Serway, John W. Jewett

Chapter21: Current And Direct Current Circuits

Section: Chapter Questions

Problem 33P: A battery has an emf of 15.0 V. The terminal voltage of the battery is 11.6 V when it is delivering...

See similar textbooks

Similar questions

A homemade capacitor is constructed of 2 sheets of aluminum foil with an area of 2.00 square meters, separated by paper, 0.05 mm thick, of the same area and a dielectric constant of 3.7. The homemade capacitor is connected in series with a 100,00- resistor, a switch, and a 6.00-V voltage source, (a) What is the RC time constant of the circuit? (b) What is the initial current through the circuit, when the switch is closed? (c) How long does it take the current to reach one third of its initial value?
A battery has an emf of 15.0 V. The terminal voltage of the battery is 11.6 V when it is delivering 20.0 W of power to an external load resistor R. (a) What is the value of R? (b) What is the internal resistance of the battery?
Three 100- resistors are connected as shown in Figure P21.41 The maximum power that can safely be delivered to any one resistor is 25.0 W. (a) What is the maximum potential difference that can be applied to the terminals a and b? (b) For the voltage determined in part (a), what is the power delivered to each resistor? (c) What is the total power delivered to the combination of resistors?
A typical cell phone consumes an average of about 1.00 W of electrical power and operates on 3.80 V. (a) What average current does the phone draw from its battery? (b) Calculate the energy stored in a fully charged battery if the phone requires charging after 5.00 hours of use.
A circuit contains a D-cell battery, a switch, a 20- resistor, and three 20-mF capacitors. The capacitors are connected in parallel, and the parallel connection of capacitors are connected in series with the switch, the resistor and the battery, (a) What is die equivalent capacitance of the circuit? (b) What is the KC time constant? (c) How long before the current decreases to 50% of the initial value once the switch is closed?
(a) What is the terminal voltage of a large 1.54-V carbon-zinc dry cell used in a physics lab to supply 2.00 A to a circuit if the cell’s internal resistance is 0.100 ? (b) How much electrical power does the cell produce? (c) What power goes to its load?
A 20.00-V battery is used to supply current to a 10-k resistor. Assume the voltage drop across any wires used for connections is negligible, (a) What is the current through the resistor? (b) What is the power dissipated by the resistor? (c) What is the power input from the battery; assuming all the electrical power is dissipated by the resistor? (d) What happens to the energy dissipated by the resistor?
(a) A defibrillator sends a 6.00-A current through the chest of a patient by applying a 10,000-V potential as in the figure below. What is the resistance of the path? (b) The defibrillator paddles make contact with the patient through a conducting gel that greatly reduces the path resistance. Discuss the difficulties that would ensue if a larger voltage were used to produce the same current through the patient, but with the path having perhaps 50 times the resistance. (Hint: The current must be about the same, so a higher voltage would imply greater power. Use this equation for power: P=I2 RP = .)
Lightbulb A is marked 25.0 W 120. V, and lightbulb B is marked 100. W 120. V. These labels mean that each lightbulb has its respective power delivered to it when it is connected to a constant 120.-V source. (a) Find the resistance of each lightbulb. (b) During what time interval does 1.00 C pass into lightbulb A? (c) Is this charge different upon its exit versus its entry into the lightbulb? Explain. (d) In what time interval does 1.00 J pass into lightbulb A? (e) By what mechanisms does this energy enter and exit the lightbulb? Explain. (f) Find the cost of running lightbulb A continuously for 30.0 days, assuming the electric company sells its product at 0.110 per kWh.
A flashing lamp in a Christmas earring is based on an RC discharge of a capacitor through its resistance. The effective duration of the flash is 0.250 s, during which it produces an average 0.500 W from an average 3.00 V. (a) What energy does it dissipate? (b) How much charge moves through the lamp? (c) Find the capacitance, (d) What is the resistance of the lamp? (Since average values are given for some quantities, the shape of the pulse profile is not needed.)
The duration of a photographic flash is related to an RC time constant, which is 0.100F for a certain camera, (a) If the resistance of the flash lamp is 0.0400 duringdischarge, what is the size of the capacitor supplying its energy? (b) What is the time constant for charging the capacitor, if the charging resistance is 800 k ?
Before a load is applied, the terminal (total) voltage of a power supply is measured to be 40 V. When a load of 500 Q is attached the voltage across the load is measured to be 36 V. Determine the following.. 40 V R E 500 N 36 V (no load) a. The current when the load is a applied: b. The internal resistance of the power supply Ω