A roadway sign that weighs Py = 14 kN is supported by a structural pipe with an outside diameter of 340 mm and a wall thickness of 10.5 mm. Wind pressure on the sign creates a resultant force of P₂ = 21 kN, acting as shown. Using length dimensions of a = 5.4 m and b = 6.3 m, determine (a) the normal and shear stresses at point H. (b) the normal and shear stresses at point K. P₂ Py b H y K

A roadway sign that weighs Py = 14 kN is supported by a structural pipe with an outside diameter of 340 mm and a wall thickness of 10.5 mm. Wind pressure on the sign creates a resultant force of P₂ = 21 kN, acting as shown. Using length dimensions of a = 5.4 m and b = 6.3 m, determine (a) the normal and shear stresses at point H. (b) the normal and shear stresses at point K. P₂ Py b H y K

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A roadway sign weighs 5 kN and is supported by a structural pipe that has an outside diameter of 295 mm and a wall thickness of 10 mm. The resultant force of the wind pressure acting on the sign is 12 kN, as shown. Assume a = 9 m, b = 5.2 m, P₂ = 12 kN, and Py = 5 kN. (a) Determine the normal and shear stresses σH, Txy at point H. (b) Determine the normal and shear stresses OK, Tyzk at point K. Answers: OH TxyH OK = TyzK || HK = i i i i b P₂ x a MPa. MPa. MPa. MPa.
A roadway sign weighs 5.3 kN and is supported by a structural pipe that has an outside diameter of 220 mm and a wall thickness of 14.5 mm. The resultant force of the wind pressure acting on the sign is 13 kN, as shown. Assume a = 8.1 m, b=4m, P₂ = 13 kN, and Py = 5.3 kN. (a) Determine the normal and shear stresses. Txy at point H. (b) Determine the normal and shear stresses Ok Tysk at point K. Answers: 0|| = Tryll = 0k = Tyck= i i MPa. MPa. MPa. MPa.
3. An axial pull of 35000 N is acting on a bar consisting of three lengths as shown below. If the Young's Modulus is 2.1 x 105 N/mm2. Determine (i) Stresses in each section, and; (ii) Total extension of the bar. Section 3 Section 2 Section 1 35000 N 35000 N 2 cm DIA 3 cm DIA 5 cm DIA k-20 cm- 25 cm -22 cm-
A standpipe with an inside diameter of 108 in. contains water, which has a weight density of Y=62.4 Ib/ft³. The column of water stands h=30 ft above an outlet pipe, which has an outside diameter of 6.625 in. and an inside diameter of 6.065 in. (a) Determine the longitudinal and hoop stresses in the outlet pipe at B. (Pressure at the outlet is P=Y*h) (b) If the maximum hoop stress in the standpipe at point A must be limited to2,500 psi, determine the minimum wall thickness that can be used for the standpipe.
At a point in a stressed body, the cartesian components of stress are sigma xx = 60 MPa, sigma yy= -40 MPa, sigma zz = 20 MPa, tau xy = -40 MPa, tau yz = 20 MPa, and tau zx= 30 MPa. Determine: (a) The normal and shear stresses on a plane whose outer normal has the following direction cosines: cos (n, x) = 0.429 ; cos (n, y) = 0.514; cos (n, z) = 0.743
A thin cylinder of inner radius 500 mm and thickness 10 mm subjected to an internal pressure of 5 MPa. The average circumferential (hoop) stress in MPa is
Extensometers attached to the external surface of a pressure vessel indicate that a = 0.002 and & = 0.005 along the longitudinal and transverse directions, respectively. Determine the corresponding stresses for E= 210 GPa and v = 0.4. What would be the error in these stresses if Poisson's ratio were not considered?
5. Segment AB of the bar is a tube with an outer diameter of d1 and a wall thickness of 0.125 in. Segment BC is a solid rod of diameter d2. The average normal stresses must not exceed 3400 psi in rod AB and 6500 in rod BC, respectively. Use P1 = 3,600 lb. and P2 = 5,500 lb. 0.125 in. di В A 6 in.- 6 in. Determine the smallest allowable value of d1 (in inches). Round-off to 2-decimal places. Your answer Determine the smallest allowable value of d2 (in inches). Round-off to 2-decimal places. Your answer Вack Next Clear form Never submit pas swords through G0ogle Forms
An advertising sign located along a city street is cantilevered from a pole as shown below. The pressure due to the wind impinging on the sign is uniformly distributed over its area and equal to p= 13.5 lb/ft² in the x- direction. The pole is fabricated from a tube with an outside diameter of d = 9.5 in. and a wall thickness of t = 0.31 in. Determine the stresses at points Cand B located at the base of the pole. Given: L₁-32 ft L₂-9.3 ft L3 CONSE TC TB = 14.4 ft Incity L₂ L₁ number (rtol-0.01, atol-Te-05) number (rtol-0.01, atol=1e-05) number (rtol-0.01, atol=1e-05) - number (rtol-001, atol-le-05) L3 → MAMA y C Ø A D ksi e -B
The stresses shown act at a point in a stressed body. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are S, = 20 MPa, S, = 24 MPa, and Sy = 29 MPa. Assume ß = tan = 21.8°, a = 5, and b = 2. Using the equilibrium equation approach, determine the normal and shear stresses o (positive if tensile, negative if compressive) and z (magnitude only) at this point on the inclined plane shown. Answers: i MPa, T = i MPа.
The thin rectangular plate (Fig. 1, not to scale) with sides 6 m and 4 m of thickness 112 mm is subjected to the stresses ox, Oy and txy. An Airy stress function is proposed to be: $(x, y) = Ax° + Bx'y+Cxy, with A=B=C =1 (a) Determine the values of stresses (ox, Oy and txy) at point (x_y) which satisfy the stress function (b) Draw a stress element showing the stresses on the four faces of the element (Use the face bounded by the X- and Y-axes with a line representing a face, that is, a 2-D stress element). (c) Neglecting body forces, determine the resultant normal and shearing forces on the right face of the plate that are consistent with o (Use the face bounded by the X- and Y-axes with a line representing a face, that is, a 2-D stress element). 112 mm 4 m 6 m Fig. 1 Biharmonic Equation ô*o(x, y) ôx o*o(x.y) ô*¢(X.y)=v*o(x,y) =0 +2 where o(x.y) is defined as: ô*o(x,y) o o(x, y) ôxcy
In a plane stress condition, the components of stress at point are ox = 20 MPa, ơy = 80 MPa and Txy = 40 MPa. The maximum shear stress (in MPa) at the point is