A roadway sign that weighs Py = 6 kN is supported by a structural pipe with an outside diameter of 335 mm and a wall thickness of 12.0 mm. Wind pressure on the sign creates a resultant force of P₂ = 21 kN, acting as shown. Using length dimensions of a = 5.2 m and b = 6.6 m, determine (a) the normal and shear stresses at point H. (b) the normal and shear stresses at point K. P₂ N b H K X

A roadway sign that weighs Py = 6 kN is supported by a structural pipe with an outside diameter of 335 mm and a wall thickness of 12.0 mm. Wind pressure on the sign creates a resultant force of P₂ = 21 kN, acting as shown. Using length dimensions of a = 5.2 m and b = 6.6 m, determine (a) the normal and shear stresses at point H. (b) the normal and shear stresses at point K. P₂ N b H K X

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

SITUATION 1: A roller at point C while hinged at A supports the frame shown below. AE =1x10° N 3m 600 N 400 N 4m 5m 1. Which of the following is the value of stress BC due to actual loads? a. 500 N с. 350 N b. 400 N d. 550 N 2. Which of the following is the value of the stress BC due to vertical one unit load applied at B? а. 1.0 с. 1.25 3. Which of the following is the value of vertical deflection at B? b. 0.75 d. 0.85 a. 6.75 mm c. 5.65 mm b. 7.85 mm d. 4.48 mm
2. If the bending stress at section 2=20 MPa. What are the bending stresses at sections 1, 3, and 4. 12 mm 12 mm 12 mm 276 mm N.A.. 12 mm 150 mm W213
1. *A propped cantilever has a 2m overhang. The beam has a load of 2W applied half way between the fixed support and the roller support and a load of W applied at the free end. What is the minimum value of W that will cause the beam to collapse? The beam has the cross-section shown below. The yield stress is 300 MPa. 75 mm 15 mm 300 mm 2W C D 15 mm 250 mm 15 mm, 2m B + 2m 2m
A rigid beam is being supported by three suspender bars made of bronze and loaded as shown in the figure. The cross-sectional area of each bar is 465 mm². Determine the average axial stress in each bar. 85 kN 56 kN 2 m D 1m 1 m E 1m 1m F LL
(See figure) A 20 mm x 120 mm beam is subjected to a load of 50 KN acting at the centroid of the cross section as shown in the figure. Point B is 20 mm below the centerline of the beam. Figure 20 300 mm 120 20 man B 50 kN a. Find the shearing stress at point B. Ans: -16.67 MRa b. Find the minimım principal stress component on the 30 degrees plane at point B. Ans: 2.98 MPa
Problem 2. Determine the minimum height h of the beam shown in the figure if the flexural stress is not to exceed 20 Mpa. 1m 2.6 kN/m R₁ 6 KN 3 m 2 m R₂ 80 mm h
8. The right-angled frame shown in the figure carries a uniformly distributed loading equivalent to 200 N for each horizontal projected meter of the frame; that is, the total load is 1000 N. Compute the maximum flexural stress at section a-a and section b-b if the cross-section is 50 mm square. 3m 4 m 5 m 3 m 2 m B
Problem 13.1. The aluminum machine part is subjected to a moment of M = 75 N.m. Determine the bending stress at points B and C on the cross section. 20 mm 10 mm 10 mm 20 mm 10 mm 10 mm 10 mm N- M= 75 N-m 40 mm Problem 13.2: For the beam shown in the figure below, determine the maximum bending stress. Misan Univers in.- 3 in. 4.0 kN 1.5 kN/m in. -1.0m-10m- 20m 2 in.
A 200 mm 50 mm Fixed to ground B 200 mm 2000 KN X A block of rubber 50 mm thick is sandwiched between two steel plates measuring 200 mm on each side as shown. A horizontal force of 2000 kN is applied to the top plate while the bottom plate is fixed to the ground. In response to the applied force, the top plate moves 5 mm in the direction of loading. a) Determine the average shear stress between the plate and rubber. b) What is the shear strain at point A and point B relative to the x-axis?
The column shown in the figure is loaded with a vertical load P = 3kN and lateral load H = 0.45kN. The column is 3m high and is made of steel with 300mm outer diameter, 6mm thick and weighs 150N/m. What is the maximum stress at the base due to the load P?
A rigid beam is being supported by three suspender bars made of bronze and loaded as shown in the figure. The cross-sectional area of each bar is 442 mm². Determine the axial stress in each bar. B 2 m O 1 m 5Q KN 1 m O E 1 m 8T KN 1 m LL
Q. No. 12: A roadway sign that weighs P,= 9 kN is supported by a structural pipe with an outside diameter of 325 mm and a wall thickness of 12.5 mm. Wind pressure on the sign creates a resultant force of P; = 21 kN, acting as shown in the Figure. Using length dimensions of a = 5.2 m and b = 6.4 m, analyse using the concepts of stresses under combined loadings to determine (a) the normal and shear stresses at point H. (b) the normal and shear stresses at point K. P, HK Q. No. 13: A 1.25-in.-diameter solid shaft is subjected to an axial force of P = 360 lb, a vertical force of V = 215 lb, and a concentrated torque of T = 430 lb-in., acting in the directions shown in the Figure. Assume that L = 4.5 in. Analyze using the concepts of stresses under combined loadings to determine the normal and shear stresses at (a) point H and (b) point K. H